齒根線 的英文怎麼說
中文拼音 [chǐgēnxiàn]
齒根線
英文
dedendum line-
Analyse the tooth geometry of klingelnberg cyclo - palloid spiral bevel gear., according to the relative position and kinematic relation of the cutter heads, virtual crown gear and the processed wheel blank, established the system of coordinates of the gear cutting, dedcuced the tooth face equation of the virtual crown gear, according to relations of the gear cutting and space theory of engagement, deduced the tooth face equation of klingelnberg cyclo - palloid spiral bevel gear, and drawing the three - dimensional graphs of the virutal crown gear and klingelnberg cyclo - palloid spiral bevel gear according to the design and setting parameters
對克林貝格擺線齒錐齒輪進行齒面幾何分析。根據銑齒加工中刀盤、搖臺和輪坯的相對位置和相對運動關系建立了切齒嚙合坐標系，由矢量的旋轉推導了產形輪齒面方程;根據空間嚙合原理和切齒嚙合關系推導了被加工齒輪的齒面方程;由設計參數和銑齒調整參數計算得到齒面離散數據，繪制了產形輪和擺線齒錐齒輪的三維齒形。In order to solve the problems of which the spiral bevel gear of oerlikon type is necessary to out and modify repeatedly, a new method was developed to predict the contact pattern and greatly reduce the cost for manufacturing by means of building a tooth contact analysis model of prolate epicycloids bevel and hypoid gears for oerlikon skm2
摘要為解決奧利康錐齒輪加工過程中需要反復試切、修正的問題，根據奧利康skm2機床建立了加工延伸外擺線齒錐齒輪和準雙曲面齒輪的齒面接觸分析模型，提出了一種可預測齒面接觸質量、降低設計加工成本的新方法。Auto trimming / colop change / stitch change machine can be set to auto or manually trim the upper / lower thread ( under thread only for lock stitch chenille ) and change color, auto or manually change among embroidery, taping, cording, zigzag or coiling
自動換色、自動選擇刺繡方式根據花樣數據及機器設定，可進行自動或手動剪線（特種繡僅剪底線）及換色、自動或手動進行平繡、鋸齒、盤帶等不同方式的刺繡組合。The thesis developed the optimization design software of geometric parameter for the worm gear including strength check module, the drawing contact lines module, the change lines of tooth thickness of worm, and the parametric modelling software for the reducer which includes parametric modelling of parts and assembly. the cad prototype system is very convenient because of its accessible interfere, simple operation and written in chinese. by input design parameters ， the cad system can make optimization design and strength check for the worm gear ， draw contact lines of tooth flank of worm - gear and change line of tooth thickness of worm ， judge if the tooth flanks of worm undercut and if the sideward tooth of worm - gear hob come to a point ， make project design and structure design for the reducer and draw its 2d parts and assembly
研究和開發了平面二次包絡環面蝸桿傳動的參數優化設計和校核軟體系統：包括幾何參數設計計算模塊，強度校核模塊，繪制齒面接觸線模塊，蝸桿齒厚變化曲線模塊和蝸桿根切判別模塊；開發了平面二次包絡環面蝸桿減速器外形與結構尺寸數據庫以及傳動效率數據庫，建立了平面二次包絡環面蝸桿傳動公差及極限偏差數據庫；開發了平面二次包絡環面蝸桿減速器參數化建模軟體：包括零部件的參數化建模模塊和裝配圖的參數化建模模塊，其中零部件的參數化建模包括蝸桿軸系的參數化建模、蝸輪軸系的參數化建模、箱體的參數化建模、端蓋的參數化建模、軸承的參數化建模和其它零部件的參數化建模軟體模塊。Abstract : the therortical calculation of the bending stress of the root and experimental stress analysis on the modified profile and the standard involute tooth profile were made with the finite element method and the electric resistance strain film method. this indicated that the modified profile was supe rior to the standard involute profiles in terms of the bending strength
文摘:分別用有限元和電阻應變片法對修形齒形和漸開線齒形進行齒根彎曲應力計算與實驗應力分析.結果證明在彎曲強度方面修形齒形比標準漸開線齒形更優越The undercut controlling of involut cylinder gear shaving
漸開線圓柱齒輪剃齒過程中的根切控制Based on the fact of driven gear moving prior to normal locality when driving gear pair moving from upper dead center to lower dead center, considering all influential elements, the maximum backlash of gear pair can be controlled to satisfy the special driving requirement through controlling the length and deviation of its common normal without increasing its manufacture precision
摘要根據換向傳動齒輪副從上止點向下止點運動時被動齒輪運動超前的實際，從影響齒輪副側隙的各種因素出發，在不提高齒輪副製造精度的前提下，通過拉制齒輪副公法線長度及其偏差從而有效地控制齒輪副的最大齒側間隙，以滿足傳動的特殊要求。This article uses advanced cad / cae software - - - ug, adams and ansys to build the integrated system platform based on theory of dynamics of multibody system for the purpose of resolving the engineering problems of general retarder design, and analyses the performance of xw - 8175 - 11 planet - cycloid retarder
本論文針對行星齒輪減速機構設計中存在的問題並根據實際工程需要，在多體動力學理論基礎上，利用cad cae軟體ug 、 adams以及ansys構建了集成的系統平臺，並在此基礎上，對xw - 8175 -型擺線針輪減速機構進行了性能模擬。On the condition of “ many - head ” and “ small drive ratio ” ， the plane double enveloping hourglass worm can not settle the problem of undercutting and sharpening simultaneously. it has devoted to a new type hourglass worm _ sphere double enveloping hourglass worm. the coordinate system is established according to the frock. the meshing equation and the tooth equation of worm and gear have been developed and the distribution of contact line on gear tooth is analyzed. to evaluate the meshing quality ， four meshing quality indexes and five original parameters are put forward. through mass programming computing ， the relations between meshing quality and original parameters are derived and depicted by graphs
考慮到平面二次包絡環面蝸桿傳動在多頭小傳動比條件下根切與齒頂變尖的矛盾很難同時解決且嚙合性能較差，介紹了一種新型環面蝸桿傳動? ?球面二次包絡環面蝸桿傳動.在研究過程中，根據工裝建立了坐標系，根據一二包過程的運動關系推得了嚙合方程和蝸桿與蝸輪的齒面方程，分析了蝸輪齒面上的接觸線分佈.為了評價嚙合性能，提出了4項性能指標和5項原始參數，通過大量編程計算得到了嚙合性能指標與原始參數之間的關系，並以圖表直觀的表示Established the system of coordinates of roll testing, getting the parameters of equation of tooth face by solving the non - linear equations set ; according to the differential geometry and meshing principle, deduce the curvature parameters of tooth face and tooth profile, and get the parameters of instantaneous contact ellipse. emulate the contact trace and contact area of the working tooth face, and drawing the instantaneous drive ratio error curve
建立了克林貝格擺線齒錐齒輪嚙合分析的對滾模型，通過對非線性方程組的迭代求解，得到齒面方程的各個參數;由微分幾何和切齒嚙合原理推導了齒面上齒廓和齒線方向的曲率參數，得到了瞬時接觸橢圓的參數。根據設計參數和機床調整參數繪制了工作齒面的接觸軌跡和接觸區圖形，並求得了瞬時傳動比的誤差曲線。As both the meshing point and ball ' s center are on the given cylinder, a general method for developing the cam ' s profile is studied. it is proved that the profile of positive and negative transmission is unique if the face gear, the difference between face tooth number and ball number and the diameter of ball are the same. the concrete expression of meshing cam on given spatial cycloid profile, and the characteristics of the profiles are discussed
論文的主要工作包括： 1 、根據嚙合點和鋼球中心軌跡均在同一圓柱面上的特點，研究了給定端齒齒廓條件下求解凸輪齒廓的一般方法；論證了在給定端齒、齒差數和鋼球直徑相同的條件下，正負齒差嚙合齒廓的唯一性；討論了端齒為球面擺線時，凸輪齒廓的具體表達式，並研究了該齒廓的性質。A mathematical model for gear shaping was presented for machining of externally meshed non - circular gears with shaping procedure in terms of the positional relationship between the tool ( cutter ) and gear ' s pitch curve
摘要根據范成法加工外嚙合非圓齒輪時刀具和齒輪節曲線間的位置關系，提出了插齒加工的數學模型。Abstract : in this paper, the kinematically admissible velocity fields are established by using the metal flow patterns based on the experiments, and the configuration dimensions of billet and the curves of load - stroke in precision forging process for spur gear from solid billet are simulated on computer by upper bound method. the results acquired in the simulation are in good agreement with those obtained in the experiments
文摘:本文利用有實驗根據的變形流動模式建立動可容速度場，利用上限法模擬用實心坯料精鍛直齒圓柱齒輪時坯料的外形尺寸變化和力?行程曲線，所得結果與實驗測定值很一致，可供沖擠精鍛工藝設計參考。Equations of mesh, shorting contact line, undercutting limit line, meshing limit lines and the existence conditions, angle between the direction of relative speed and the direction of contact line, induced normal curvature about every point on the contact line are established. moreover, the paper also theoretically analyzed the error of the grinded gear surface. on the basis of the theory, the computer program is worked out to automatically produce the contact line and the boundary curves of mesh. analysis of meshing circs under different parameters can be done so that we can gain the best process condition
首先對漸開面二次包絡理論進行了深入的探討，推導出了兩次嚙合的嚙合方程式、瞬時接觸線方程式、根切界限線方程式、嚙合界限線的方程式及其存在條件，相對運動速度方向與接觸線方向的夾角及接觸線上各點的誘導法曲率；此外，還對磨齒后工件的齒面誤差進行了理論分析；並在理論基礎上編制了相應的計算機程序，自動生成接觸線族及嚙合界限線，對不同參數條件下的嚙合情況進行分析，可以使工藝條件達到最佳狀態；最後研究了磨齒裝置，設計了磨齒機的傳動系統。Tooth surface equations and contact line equations of the involute worm gearing are established according to its machining methodology. meshing characteristics in rigidity condition are studied. these characters include the inductive normal curvature along the contact line on the worm surface, the first and the second limit lines during the engage of the worm gear, and the influence of the intersect angle between the contact line the relative velocity of the worm and the gear on transmission performance
根據漸開線圓柱蝸桿傳動的創成方法，建立了漸開線圓柱蝸桿和蝸輪的接觸線方程式、齒面方程式，分析了漸開線圓柱蝸桿傳動的剛性嚙合特性，如蝸桿與蝸輪嚙合時的誘導法曲率、一類界限曲線、二類界限曲線和蝸桿與蝸輪間相對速度方向和接觸線方向的夾角對傳動性能的影響； 2The effect of the corner radius on root stress of involute gear
刀尖圓弧半徑對漸開線齒輪齒根應力的影響A calculation research on the tooth root bending stress of asymmetrical involute gear
非對稱漸開線齒輪齒根彎曲應力的計算分析After thoroughly analyzing the influence of each pump parameters on the gear pump performance, the paper developes the criterion for optimum gear parameters, which can be utilizied in practice easily for gear manufacturing using normal involute gear hob with two - fillet type. the conclutions studied by the paper are : 1. both the addendum coefficient and the deddendum coefficient of the pump gear should be 1. 125
以目前國內普遍使用的雙圓弧頭全齒高為2 . 5倍模數漸開線標準滾刀作為泵齒輪的加工刀具，通過對齒輪加工原理的分析，提出了欲使泵齒輪參數達到最佳，泵齒輪的齒頂高系數和齒根高系數都為1 . 125 ；對變位系數的確定應考慮到泵齒輪的根切、齒頂厚、重合度以及側隙因素；泵齒輪為避免過渡曲線干涉，必然要存在根切現象。Gear form is precisely, plotted by portray point. for friendly user interface, the dialog - box is given, using dcl language to compile dialog box program. because the given program can not only output all the optimum basic parameters of pump gear, but also simulate the meshing process of a pair of pump gears, gear pump can be designed and manufactured economically
精確繪出泵齒輪的輪齒幾何形狀，尤其精確繪制出了標準齒輪滾刀切出的齒根過渡曲線，演示了國標雙圓弧頭標準滾刀加工泵齒輪的過程，並實現了泵齒輪副的嚙合模擬，這些對檢查輪齒干涉以及確定齒輪泵的卸荷槽位置和形狀提供了依據。Compared with a standard involute gear, the unsymmetric involute gear could efficiently improve the tooth root bending strength by finite element analysis
對實例的有限元分析表明非對稱漸開線齒輪的齒根彎曲強度比對稱齒輪有較大提高。分享友人