齒條 的英文怎麼說

中文拼音 [chǐtiáo]
齒條 英文
[機械工程] rack; gear [pinion; ratchet; toothed] rack; rack rod; rackwork; teeth [toothed] bar; spline
  • : Ⅰ名詞1 (牙; 牙齒) tooth 2 (物體上齒形的部分) a tooth like part of anything 3 [書面語] (年齡...
  • : Ⅰ名詞1 (細長的樹枝) twig 2 (條子) slip; strip 3 (分項目的) item; article 4 (層次; 秩序; 條...
  1. Vertical motion of the carriage is provided by a pulldown gear case coupled by two pinions to racks on the mast

    滑架的垂直移動是由一個下拉輪箱提供的,該下拉輪箱則通過兩個小輪連接到支架上的齒條上。
  2. Horology. involute toothing gears. basic racks

    鐘表業.漸開線輪.基本齒條
  3. Contro1 of deformation of nodular cast iron rack during manufacture

    球墨鑄鐵齒條變形的控制
  4. The four main types of gears (spur, helical, worm, and bevel)and a rack and pinion are shown in figure 7.

    圖7所示是四種主要的輪(巨輪,斜輪,蝸輪和傘輪)以及齒條和小輪。
  5. Tabular layouts of article characteristics for racks, cylindrical gears, pinion shafts, bevelgears, bevel pinion shafts, worms and worm wheels

    齒條圓柱輪小輪軸傘輪圓錐輪軸蝸
  6. Abstract : requirements for hydraulic steering rack cylinder are very high, the rack cylinder should be durable, lubricants preservable and of seal. so, finish machining and parameter - set are necessary

    文摘:液壓轉向機對齒條桿部表面有很高的耐磨、儲油、封存要求,為此需要一套表面超精加工工藝及加工參數設定。
  7. The basic data for rack pusher of furnace in rolling mill

    軋鋼車間加熱爐齒條式推鋼機.基本參數
  8. Recirculating ball - rack and sector steering gear

    循環球齒條扇式轉向器
  9. Witch has worked out the tooth shape of datum rack and computer simulation of gear manufacture. pointedness, undercut and tooth tip becoming sharp are analysed. tooth thickness calculation and measurement, superposition coefficient calculation and belt length calculation are resolved

    2 、給出了基準齒條廓形狀,進行了輪加工計算機模擬,分析了可能出現的稜角問題,進行了輪內頂圓的求解、根切問題分析、厚計算與測量、頂變尖的分析、重合度的計算、帶長度的計算及輪設計的程序編制等。
  10. Finally, the three dimensional configurations are imported to 3dmax software. making great use of powerful entity rendering and animating ability in 3dmax software realizes gear - spline mesh, gear - gear mesh and cam - block moving dynamic simulation

    最後,將三維實體傳遞到3dmax中,利用3dmax強大的實體渲染和動畫製作功能,實現了齒條嚙合、輪嚙合和凸輪滑塊運動的動態模擬。
  11. Through analysis of the change of the specifications of the clothing wires made of alloy steel before or after the tempering process, the paper puts forth that installation of tempering device after the punching and quenching process is helpful to better quality of clothing wires, improving the color difference of clothing and prolong the service life of clothing

    摘要通過分析合金鋼針布齒條回火前後各項指標的變化,指出在沖淬工藝后加裝回火裝置有助於提高金屬針布性能,改善針布齒條色差,延長其使用壽命。
  12. Specification for generating racks for synchronous belt drive pulleys

    皮帶同步傳動輪齒條規范
  13. Abstract : with pc - controlled liquid drop counter, protective atmospher es of ball annealing of wires is strictly kept. pickling is easily gained in proc ess of ball annealing of wires and quality wires are produced

    文摘:採用電腦液體滴速計數儀,嚴格控制針布齒條用規格鋼絲球化退火的保護氣氛,防止和消滅針布齒條在球化退火過程中出現的表面不易酸洗現象,提高了鋼絲的表面質量。
  14. The fuel rack requires little force to accomplish its motion.

    油泵齒條幾乎毋須費力就能使之移動。
  15. New metallic clothing for wool cayding

    精紡梳毛機用新型針布齒條探析
  16. Specification for rack type gear cutters, metric module

    米制模數齒條式銑刀規范
  17. The moment of inertia, damp and comeback can be adjusted. two electro - hydraulic servo systems analog rolling moment and swaying force of wave respectively. the two systems both use electro - hydraulic servo valves, in which the analog rolling moment system adopts gear - rack swing hydraulic - pressure oil vat with torque sensor, while the analog swaying force system employs double shanks hydraulic - pressure oil vat with two pressure sensors and a placement sensor

    兩套電液伺服系統均使用流量電液伺服閥(採用外供油方式) ,其中模擬橫搖力矩的伺服系統採用齒條擺動液壓油缸,配有扭矩傳感器,模擬橫蕩力的伺服系統採用雙出桿液壓油缸,配有兩個壓力傳感器和一個位移傳感器。
  18. Gear drawing standards - part 1 : for spur, helical, double helical and rack

    輪制圖標準.第1部分:正.螺旋.雙螺旋齒條
  19. We proposed four kind of it and analyzed their structure. this kind of new actuating mechanism can realize the going around a turn under the condition of steady and smoothing, so it can realize the transmission continuous and long distance round about movement with the whole equipment

    同時,為了使該機構能夠實現正常的曲線嚙合,在漸開線柱鼓形輪和空間齒條機構之中引入了一個導引機構,並對其進行了結構設計和樣機製造,從而使這種空間齒條機構實現了平穩的空間曲線嚙合傳動。
  20. In this paper, we designed the structure of the gear and rack in this actuating mechanism, elaborated the theory of its formation, and deduced the profile function and gearing function of the gear and rack. furthermore, we deduced the inherent radius of going around a turn under certain circumstance, the condition of the correct gearing and the continuous transmission. in order to make the mechanism move steady, we designed the derivation mechanism and manufacture the modle

    本文對該傳動機構中的漸開線柱鼓形輪和空間齒條的結構進行了設計,並給出了輪和齒條的成型原理,推導出了漸開線柱鼓形輪和空間齒條廓參數方程、嚙合方程;進一步分析並確定了漸開線柱鼓形輪、空間齒條在給定嚙合傳動件下所能實現的固有轉彎半徑和運動約束件,並對其側隙及效率進行了計算和分析。
分享友人