齒狀結構 的英文怎麼說

中文拼音 [chǐzhuàngjiēgòu]
齒狀結構 英文
dentalation
  • 齒 : Ⅰ名詞1 （牙; 牙齒） tooth 2 （物體上齒形的部分） a tooth like part of anything 3 [書面語] （年齡...
  • 狀 : Ⅰ名詞1 （形狀） form; shape 2 （情況） state; condition; situation; circumstances 3 （陳述事件或...
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 構 : Ⅰ動詞1 （構造; 組合） construct; form; compose 2 （結成） fabricate; make up 3 （建造; 架屋） bui...
  • 結構 : 1 （各組成部分的搭配形式） structure; composition; construction; formation; constitution; fabric;...
  1. Because of the lower rock fragmentation efficiency and defective geometrical shape of chisel bit, sweden has replaced chisel bit with taper connecting cross chisel bit and button bit since the mid - seventies

    因一字形釬頭破巖效率低和幾何形狀結構缺陷等問題，瑞典從70年代中期就用錐體連接的十字和球齒釬頭取代了一字形釬頭。
  2. Abstract : through the structure character of the chain pulley on the plow, this paper discusses the manufacturing principle and the gear - plane shape of the chain pulley when it is milled with cyclinder milling blade. it not only introduces in detail the structure and using method of the chain pulley surface tyre when it milled, but also analyzes gear - shape error which generates in the during milling

    文摘:就刨煤機鏈輪的結構特點論述了用圓柱銑刀銑削鏈輪齒面的加工原理及所形成的齒面形狀，詳細介紹了銑削鏈輪齒面胎具的結構及使用方法，並對加工過程中產生的齒形誤差進行了分析和闡述。
  3. The situation and development of domestic and foreign manufacture, especially in the europe, america and asia, have been summarized and researched in the article, so the following work has been finished, and the conclusions and results are obtained as follows : through analyzing the features of movement, power and construction for the high - speed cnc gear hobbing machine in 6 - axis with four coordinated, the design methods of general arrangement, kinetics and kinematics are put forward. 1. by analyzing the severe challenge to the machine manufacture in the market, developing and managing methods of serial modular products are posed

    為了給我國汽車工業和其它行業提供先進的齒輪加工設備，本文在總結、研究國內外特別是歐美國家齒輪機床現狀與發展的基礎上，進行了以下研究工作，並得出相應的結論與成果：分析了六軸四聯動數控高速滾齒機的運動、動力、結構特點，提出了六軸四聯動數控高速滾齒機的總體布局設計、動力設計、運動學設計方法；分析並根據市場對機床製造業提出的嚴峻挑戰，提出了數控滾齒機系列產品的模塊化開發方法與管理方法；在分析了六軸四聯動數控高速滾齒機模塊化設計的技術先進性與經濟性間辨證關系的基礎上，提出了產品開發過程中以邊際成本法進行經濟分析的方法。
  4. In this paper, the cold die forging technology of the counter gear was analysed, the cold die forging was designed, the blank dimensions and the figure were calculated and choosed, the allowable deformation degree was checked, the equipment for the deformation was selected, the blank treatments before the cold die forging were draw up and the die structure of the cold die forging was designed

    分析了計數器齒輪的冷模鍛工藝，設計了冷模鍛件圖，計算及選用了毛坯尺寸及形狀，驗算了許可變形程度，選擇了變形用的設備，擬制了冷模鍛前的毛坯處理及設計了冷模鍛模具結構。
  5. Abstract : in this paper, the cold die forging technology of the counter gear was analysed, the cold die forging was designed, the blank dimensions and the figure were calculated and choosed, the allowable deformation degree was checked, the equipment for the deformation was selected, the blank treatments before the cold die forging were draw up and the die structure of the cold die forging was designed

    文摘:分析了計數器齒輪的冷模鍛工藝，設計了冷模鍛件圖，計算及選用了毛坯尺寸及形狀，驗算了許可變形程度，選擇了變形用的設備，擬制了冷模鍛前的毛坯處理及設計了冷模鍛模具結構。
  6. Rotating machines ( i. e. gear - box ) are always assembly of many associated parts, such as gears and bearings. commonly, high rate of fault isolation for such machines need enough test points. since the machines are always too compact to fix enough sensors, it is significative to study on how to use fewer sensors for machine monitoring and fault diagnosis by vibration analysis of rotating machine groups

    復雜的旋轉機械往往由軸承、齒輪等大量零件構成，在對這樣的設備進行狀態監控和故障診斷時，為提高故障隔離率，通常需要為每個零件就近安裝傳感器，但由於機械結構的緊湊性和性價比的限制，這一點往往難以實現。
  7. Taking a rotor shape parameter as a variable, the minimum volumes of rotor cavity and pump flow as the design objectives, as well as some constraints on rotors and gears cavity structures, an optimization design model of un - contact rotor pump was constructed

    摘要以轉子形狀參數為變量，以流量和轉子腔體積最小為設計目標，考慮齒輪腔和轉子腔結構的有關約束，建立了非接觸式轉子泵的優化設計模型，給出了優化設計步驟。
  8. Abstract : the paper presents the research into the stress state of roller teeth using fem ( finite element method ). the results show that different structure parameter causes a change in roll stress

    文摘:採用有限單元法對軋輥輥齒的應力狀態進行了研究，得出了不同結構參數對軋輥應力變化的影響。
  9. Anatomical integration of newly generated dentate granule neurons following traumatic brain injury in adult rats and its association to cognitive recovery

    外傷性腦損傷后成年老鼠新生齒顆粒狀神經細胞結構整合與認知力恢復的聯系。
分享友人
分享到 Line

分享到臉書