齒的彎曲強度 的英文怎麼說

中文拼音 [chǐdewānqūqiángdù]
齒的彎曲強度 英文
beam strength of tooth
  • 齒 : Ⅰ名詞1 （牙; 牙齒） tooth 2 （物體上齒形的部分） a tooth like part of anything 3 [書面語] （年齡...
  • 的 : 4次方是 The fourth power of 2 is direction
  • 彎 : Ⅰ形容詞（彎曲） curved; bent; crooked; flexuous; tortuous Ⅱ動詞1 （使彎曲） curved; bend; flex 2 ...
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 強 : 強形容詞（強硬不屈;固執） stubborn; unyielding
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  1. After being improved, the gear surface contact fatigue strength obeys weibull distribution and stress obeys normal distribution, the gear bottom bend fatigue strength and stress obey logarithm normal distribution, according to the relation of average safe rate and reliability, then the gear strength reliability design and check equations can be deduced

    將齒面接觸疲勞強度按威布爾分佈、應力按正態分佈處理，將齒根彎曲疲勞強度和應力均按對數正態分佈處理，再根據平均安全系數和可靠度之間的關系，推導出了齒輪強度可靠性設計和校核公式。
  2. Among the results of these researches, cylindrical gears with curvilinear tooth trace have merits as follows : higher bending stress, low noise, better lubrication conditions, and no thrust forces. so this kind of gear can be considered to substitute the helical gear and herringbones

    本文提出的弧齒線圓柱齒輪是一種新型齒輪傳動形式，具有傳動平穩、噪聲低、潤滑性能良好、輪齒彎曲疲勞強度大的特點，因此該齒輪可以作為斜齒輪和人字齒輪的替代品用於高速重載場合。
  3. This paper mainly discussed the optimization design of two - stage star - type gear transmission system. it covered the two sides : one - stage gear transmission and two - stage gear transmission. on the basis of their analysis and research, the mathematic models are created which include the objective functions of minimum volume and minimum center distance, the constraints of contact strength, bend strength and scuffing strength

    本文主要研究了航空發動機星型齒輪傳動系統的優化設計，對單級齒輪傳動和兩級星型傳動都進行了深入的分析和探討，分別以系統體積最小和中心距最小為目標函數，以齒輪的接觸強度、彎曲強度、膠合強度等為約束條件，建立了完整的數學模型。
  4. The results indicate that if the value of press stress is over certain figure, press stress and al plate ’ s thickness have little influence on sawtooth distortion for the same kind of sawtooth ; sawtooth distortion is well - regulated under static press, while it is irregular under impact press. bottom coating make great influence on bond strength of samples which can improve the value remarkably ; bonding mechanism of clad steel is mechanism of mechanical effect that sawtooth which is hooked occludes with al plate

    結果表明：同種齒型，當壓應力大於一定的值時，壓應力和覆板的厚度對齒形的變化影響不大；靜壓下齒形變化比較規則，鋸齒頂端向一側彎曲成鉤狀；沖壓下齒形比較凌亂，鋸齒的頂端沒有明顯的變形；后處理對試樣的結合強度影響很大，打底試樣由於粘結層的作用，結合強度較高；機械作用機制是復合鋼板的主要復合機理，鋸齒彎曲成鉤狀和鋁板形成機械咬合。
  5. Beam strength of tooth

    齒的彎曲強度齒輪
  6. Calculation of load capacity of spur and helical gears - calculation of tooth bending strength

    正齒輪和斜齒輪承載能力的計算.第3部分:齒牙彎曲強度計算
  7. 3. base on the numeric method of finite element, the influence of interrelated shift coefficient and tooth number z to bend intensity of gear is studied. with the increase of the tooth number, tooth root maximum pull stress decrease ; with the increase of the interrelated shift coefficient, tooth root maximum pull stress increase

    3 、基於有限元數值計算方法，分析了不同關聯變位系數和齒數z對齒輪彎曲強度的影響：隨著齒數的增大，齒輪最大拉應力減小；關聯變位系數越大，齒輪最大拉應力越大。
  8. Compared with a standard involute gear, the unsymmetric involute gear could efficiently improve the tooth root bending strength by finite element analysis

    對實例的有限元分析表明非對稱漸開線齒輪的齒根彎曲強度比對稱齒輪有較大提高。
  9. 5. software designing about planetary - gear transmission. it consists of calculation of equivalent error of the averaged load component, force and deformation analysis of component, contact stress and bending strength analysis. 6

    用vb6 . 0自行開發了行星變速箱計算機輔助分析程序設計，該分析程序主要功能包括均載件的等效誤差、各部件的受力及變形分析及齒輪彎曲強度及接觸強度校核6
  10. Rating the pitting resistance and bending strength of generated straight bevel, zerol bevel and spiral bevel gear teeth

    直齒傘齒輪齒，弧齒傘齒輪齒，螺旋傘齒輪齒的耐點蝕性和彎曲強度的評定
  11. Research on wear - resistance and bending strength of modified tooth profile involute gear

    修形齒輪耐磨性和彎曲強度的研究
  12. An application of finite element method on bending fatigue strength calculation of the teeth of a standard straight spur gear

    有限元法在標準直齒圓柱齒輪輪齒彎曲疲勞強度計算中的應用
分享友人
分享到 Line

分享到臉書