齒輪圈 的英文怎麼說

中文拼音 [chǐlúnjuān]
齒輪圈 英文
gear rim
  • : Ⅰ名詞1 (牙; 牙齒) tooth 2 (物體上齒形的部分) a tooth like part of anything 3 [書面語] (年齡...
  • : Ⅰ名1 (輪子) wheel 2 (像輪子的東西) wheel like object; ring; disc 3 (輪船) steamer; steamboa...
  • : 圈名詞1. (養豬羊等牲畜的建築) pen; fold; sty 2. (姓氏) a surname
  • 輪圈 : rim section; rim (of a wheel)
  1. Tooth profiles and structural characteristic of ring gear of epicyclic drive with eccentric wheel and push rod

    偏心推桿行星傳動內廓及其結構特性研究
  2. For the first time, the internal gear is manufactured in nc machine

    首次在數控機床上完成了中心廓的加工。
  3. The construct of the parts of swing movable teeth reducer is studied, renovating design of eccentric gear, moveable teeth and internal gear is given

    探討了擺動活減速器中各零部件的結構,從提高傳動效率出發,對擺動活減速器的偏心激波器、活、中心的結構進行了改進設計。
  4. The relative speed between movable tooth and internal gear, the coordinates of points of internal gear are calculated by matlab. then a new method of calculating the gear curve of internal gear is put forward

    並利用matlab軟體編程,求出了活與中心的相對速度,中心形點的坐標,從而提出了一種中心形求解的新方法。
  5. Set up the following 2d parametric models : ( dinitial contour of cone. ( 2 ) six types of inserts : cut insert, conical insert, ovoid insert, chisel insert, gage insert and scoop chisel insert. ( 3 ) twelve types of slots : six slots between the rows of inserts ; six slots on the head of cone

    建立了以下幾種二維參數化模型: ( 1 )牙初始廓; ( 2 )六種牙,包括平頂、錐形、球形、楔形、邊楔和勺形; ( 3 )十二種槽,其中六種牙之間的槽、六種牙頂端的槽。
  6. Flywheel ring gear

  7. 3. solve the key problem during the 2d engaging design of the tri - cone rock bit. if you move or rotate any insert with mouse, the other two inserts in the same cycle change same positions

    解決了三牙鉆頭二維嚙合設計中的關鍵技術?聯動布,通過鼠標移動和旋轉任意一個牙,同一上的其它兩個牙做相同的位置變動。
  8. The points of internal gear are fitted into spline curve by spline function, then the internal gear is manufactured in nc wire - cut machine. the process of manufacturing the internal gear in wire - cut machine is studied. compared to the traditional method of manufacturing in special machine this process is a breakthrough

    利用樣條函數對中心形點進行擬合,利用軌跡法在數控線切割機床( bkdc )上實現了中心形的加工,並對在數控機床上加工的工藝進行了研究。
  9. The precision of the non - contact testing of flywheel gear ' s contour and location error of light electricity inspection machine based on virtual instrument has been carried on theory analysis in this paper. various contour and location tolerances of the part have been distributed depending on the result of the analysis, and the data handling method of measurement has been studied to find a data handling method of getting rid of the system error under one kind of condition of the big sample space

    本文對飛形位誤差光電檢驗機的精度進行了理論分析,依據分析的結果分配了零件的各種形位公差,並對測量結果的數據處理方法進行了研究,找到了一種在大樣本空間的條件下依概率排除系統誤差的數據處理方法,同時為了驗證其可靠度對其進行了計算機模擬實驗。
  10. For the first time, the internal gear is measured on three - coordinate measuring machine, gear error of internal gear is calculated and analyzed by comparing the measuring data with the desired data. the result of analyzing reveals the correctness of math model and manufacturing method

    首次在三坐標測量機上實現了中心形的檢測,並把檢測數據與理論數據進行比較,求出了中心形誤差,通過對形誤差的分析,證明了以上數學模型是正確的,加工方法是可行的。
  11. Translation modes are similarly independent of the rotational support stiffnesses. large contact ratio do not mean lower mesh force. if either the number of sun or ring gear is not multiple of planet gear, system will run effectively, with lower impaction of tooth mesh in and out

    研究表明:扭轉支撐剛度的變化影響系統的轉動模態,徑向支撐剛度(行星架的除外)的變化影響系統的位移模態;間重合度大並不等於間的受力情況好;行星與內數不為行星個數的整數被時,的嚙入、嚙出對系統的沖擊小,系統的效率高。
  12. Cup, pinion rear bearing

    主動后軸承外
  13. Cup, pinion front bearing

    主動前軸承外
  14. The babbitt adjustable sprocket rim will provide for remote operation of butterfly valves in high, normally out - of - reach locations

    巴比特合金可調節鏈齒輪圈,可用於位於高處,通常難于接近的蝶閥的遠程操作。
  15. The main work and results are as followings. according to gear engagement principle, the math model of swing movable teeth drive is established. the engagement curve, engagement equation, relative speed between eccentric gear and movable teeth, and between movable teeth and internal gear are presented, and the gear equation of internal gear is presented

    取得了以下研究成果:根據嚙合原理,建立了基於嚙合原理的擺動活傳動的數學模型,推導了偏心激波器與活、活與中心的接觸線方程、嚙合方程、相對速度和中心形方程。
  16. The " calendar round " is like two gears that inter - mesh, one smaller than the other

    「歷法圓」就像兩個互相嚙合的,一個比另一個更小。
分享友人