齒輪架 的英文怎麼說

中文拼音 [chǐlúnjià]
齒輪架 英文
wheel brace
  • 齒 : Ⅰ名詞1 （牙; 牙齒） tooth 2 （物體上齒形的部分） a tooth like part of anything 3 [書面語] （年齡...
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 架 : Ⅰ名詞1 （用來放置東西或支撐物體等的東西; 架子） frame; rack; shelf; stand 2 （毆打; 爭吵） fight;...
  • 齒輪 : gear [rack; toothed] wheel; （toothed） gear; wheel gear
  1. Vertical motion of the carriage is provided by a pulldown gear case coupled by two pinions to racks on the mast

    滑架的垂直移動是由一個下拉齒輪箱提供的，該下拉齒輪箱則通過兩個小齒輪連接到支架上的齒條上。
  2. Bevel pinion shaft carrier

    小錐齒輪軸架
  3. Abstract : the effect of different carburizing programs on the microstructure and thick of carburized layer of screw bevel gears has been studied, meanwhile the fatigue life of these gears has also tested

    文摘:本文研究了不同滲碳淬火工藝對螺傘齒輪組織及滲層深度等影響，並對螺傘齒輪進行了臺架疲勞測試。
  4. It is shown from results that increasing carburizing time further in the normal technology can not obviously deep the carburizing layer, but can cause nonmartensite microstructure at the bottom of the gear and coarse grain across the gear, these will heavily decrease the fatigue life of the gear

    結果表明：在正常滲碳淬火工藝基礎上再延長滲碳淬火1小時，齒輪滲碳層深度變化不大，但其齒根局部表面處有非馬組織，且晶粒尺寸易產生異常長大現象，從而致使臺架疲勞壽命明顯下降。
  5. Change gear bracket

    交換齒輪架
  6. The combine harvester is overall 3 packets of period of efficacy are 1 year ; 3 packets of period of efficacy are main part 2 years, main part is to point to internal - combustion engine airframe, cylinder housing of casing of lid, flywheel, frame, gear - box, clutch, change gear case of machine, final drive to body

    聯合收割機整機三包有效期為1年；主要部件三包有效期為2年，主要部件是指內燃機機體、汽缸蓋、飛輪、機架、變速箱箱體、離合器殼體、轉向機、最終傳動齒輪箱體。
  7. Abstract : this paper introduced the induction hardening experiment of components ? the gear - park and the drive support sprocket. give some advise on the pearlitic malleable iron ' s induction heat - treatment, and show coil design intending to meet the harden profilc according to the drawing

    文摘:本文介紹變速箱零件? ?駐車齒輪和鏈輪支架的感應淬火試驗工作，提出對可鍛鑄鐵感應淬火中值得注意的問題及針對這兩種零件的特殊硬化層要求而設計的感應器。
  8. The existence of a c - c ( crank - crank ) type of geared five - bar linkages linked with the ground link, the classification and the range of gear ratio and phase angle in the fully rotatability of geared five - bar linkages were mainly studied in this dissertation

    本論文主要研究了齒輪?五桿機構中與機架相連的兩連架桿的雙曲柄的存在條件、齒輪?五桿機構的分類以及在每一分類中齒輪?五桿機構能夠整周轉動時其相位角和傳動比的范圍。
  9. The utility model belongs to the material processing machinery, which comprises mountings, bearings, gears, revolving axles, cutting tools, radial adjusting devices, and angle adjusting devices etc

    它包括機架、軸承、齒輪、回轉軸、刀具、徑向調整裝置、角度調整裝置等。
  10. The changing carbon potential carburization - hot oil matrempering technology of helical bevel gear for automobile driven axle is introduced in this article. the board test and production application show that the technology not only quenchs directly gear after carbrization, but also decreases the heat treatment deformation and raises the contact fatigue life of gear

    介紹了汽車驅動橋螺旋錐齒輪的變碳勢滲碳一熱油分級淬火工藝，臺架試驗及生產應用表明，該工藝與專用滲碳淬火掛具相結合，不僅可實現齒輪滲碳后直接淬火，而且熱處理變形小，齒輪接觸疲勞壽命也有所提高。
  11. Simple single yoke construction eliminates outside gearing and bearings

    簡單的單軛架結構，避免採用外部齒輪和軸承。
  12. Gear bracket support

    齒輪托支架
  13. Planetary gear carrier

    行星齒輪架
  14. At the same time, we research the data remote transfer, and realize the remote computing of gear

    在系統結構框架的基礎上，結合齒輪的基本設計要求，初步實現了齒輪的遠程計算和設計。
  15. It consists of a car - riage, a rotary gear reducer and a hoist gear reducer

    它由一個滑架、一個轉動齒輪減速器和一個提升齒輪減速器組成。
  16. We go all out to provide various reliable upper - and - lower ball joint for independent suspension, or rack end for rack - and pinion steering

    我們竭誠提供始終為中外新老客戶值得信賴的各種結構形式的獨立懸架用上下球較節，和齒輪齒條轉向機構的齒條接頭。
  17. Any special requirements such as gear operation, motor operation, hydraulic or pneumatic cylinder operation, anti - friction bearing yoke sleeve, by - pass of drain, etc. must also be specified on purchase orders

    如果有特殊要求，如齒輪操作機構，馬達執行機構，液動或氣動缸體執行機構，耐摩擦軸承軛架套管，排泄旁路，等等，在訂購時都必須特別註明。
  18. The differential pinions mounted on the legs of the spider revolve around the center axis of the spider as the differential case rotates

    差速器小齒輪安裝在方向節十字軸支架上，在差速器齒輪箱旋轉時，它會繞著方向節十字軸的中心軸一起旋轉。
  19. Translation modes are similarly independent of the rotational support stiffnesses. large contact ratio do not mean lower mesh force. if either the number of sun or ring gear is not multiple of planet gear, system will run effectively, with lower impaction of tooth mesh in and out

    研究表明：扭轉支撐剛度的變化影響系統的轉動模態，徑向支撐剛度（行星架的除外）的變化影響系統的位移模態；齒輪間重合度大並不等於輪齒間的受力情況好；行星輪與內齒圈齒數不為行星輪個數的整數被時，輪齒的嚙入、嚙出對系統的沖擊小，系統的效率高。
  20. Planetary pinion carrier

    行星齒輪機構的行星架
分享友人
分享到 Line

分享到臉書