齒鍵 的英文怎麼說
中文拼音 [chǐjiàn]
齒鍵
英文
alligator-
Keyway broach with chamfer types and dimensions
帶倒角齒鍵槽拉刀型式與尺寸Driving system consists of synchronous belt ( optibelt, made in germany ) and round arc gear combined with gear case ; the key parts adopt nsk bearing ( made in japan ) for smooth transmission, prolonging the lifetime of the machine
傳動部位，可採用德國歐皮特同步帶，圓弧齒輪，齒輪箱相結合，關鍵部位採用了日本nsk軸承，實現設備傳動平穩，壽命延長。Based on the analysis of the advantage and disadvantage of both overseas and domestic closed cold forging equipment, closed cold forging equipment consisting of a nc precise forging hydropress and a set of hydraulic drive female die has been developed, hence realization of the precision die forging of key parts for car, such as bevel gears
摘要在分析了國內外現有閉式冷精鍛裝備的優缺點的基礎上，開發研製了數控精鍛液壓機和液壓傳動凹模模具裝置，構成閉式冷精鍛設備，實現了圓錐齒輪等轎車關鍵零件的精密模鍛生產。Gear and spline drawing standards - part 2 : bevel and hypoid gears
齒輪和花鍵制圖標準.第2部分:傘齒輪和準雙曲面齒輪Straight cylindrical involute splines measuring pin
圓柱直齒漸開線花鍵量棒Straight cylindrical involute splines inspection methods
圓柱直齒漸開線花鍵檢驗方法For the 30. 2mm shaft, there are still larger over measure to load. the strength is increased by optimization. for ? 17. 4mm shaft, the strength is increased by enlarge the inner dimension of the spline ; for 30. 2mm shaft, the strength is increased by adjust the structure at the boundary between the key groove and the ring groove, the highest stress of the shaft is at bottom and terminal of the spline after optimization
其中對17 . 4mm泵軸的優化，通過增大花鍵內徑，提高了花鍵齒底的強度，降低了應力集中點附近的應力；對30 . 2mm電機軸的優化，通過在軸承鍵的環槽端增加倒角，有效降低了該位置的應力集中，使軸的最大應力點從軸承鍵與環槽的交界處轉變到花鍵根部與收尾的交界處，提高了電機軸整體結構強度的合理性。Specification for straight - sided splines and serrations
直邊花鍵與鋸齒形花鍵規范Technical drawings - representation of splines and serrations
技術制圖.花鍵和鋸齒形花鍵的畫法Technical drawings. representation of splines and serrations
技術圖紙.花鍵和鋸齒形花鍵的表示方法Serrations for surgical instruments ; profile angles, groove distances
外科器械的細花鍵連接.齒形角槽的間距Undercuts for splines - design standard
花鍵齒的牙底削平.設計標準Size and obliquity of tooth directly influence clutch whether normal operating. it is a key part for ensuring normal operating of aira too. this article fully deduces their compute formula
該齒形的大小、傾角直接影響離合器是否能正確地嚙合和分離，也是保證機構進行正確工作的關鍵部分，本文詳盡推導了它們的計算公式。By means of analytical methods based on upper bound element technique ( ubet ), non - axisymmetric element, simulates the forming process of non - axisymmetric involute teeth spline has been introduced, formula of speed fields been derived and the deformation regularity of steady extrusion on the forming process successly described
摘要本文運用上限單元技術（ ubet ） ，引入非完全軸對稱單元，模擬了非完全軸對稱零件漸開線齒外花鍵的成形過程，推導出了成形過程中的速度場公式，並成功地描述了擠壓過程中的變形規律。Author keywords biomechanical analysis ; cerical spine ; atlas ; axis ; arthrodesis ; instrumentation ; odontoidectomy ; spinal instability
關鍵詞：生物力學分析；頸椎；樞椎；軸；關節固定術；器械；齒突切除；脊柱穩定。These may seem trivial points, but as the first wave of replacement organs start to make their way toward the clinic, teeth will serve as a crucial test of the feasibility of different tissue engineering techniques
這看起來或許沒什麼了不起，但在第一批替代器官進入臨床之前，牙齒實驗將會是關鍵，可檢視各種組織工程技術是否可行。Three key milestones must therefore be reached to establish whether engineering replacement biological teeth is possible
因此，要確定是否能夠成功製造出生物性替代牙齒，必須先達到三個關鍵的里程碑。Side and face cutters with straight teeth with key drive
鍵傳動的直齒三面刃銑刀Side and face cutters with staggered tooth with key drive
鍵傳動交叉齒的三面刃銑刀Interlocking side and face cutters with staggered tooth with key drive
帶鍵傳動的交錯齒的互聯的三面刃銑刀分享友人