abrasion 中文意思是什麼

音標 [ə'breiʒən]
abrasion 解釋
n. 名詞 1. 磨去；擦去。
2. 擦傷，磨損。
3. 磨蝕；【地質學；地理學】沖蝕，海蝕。

  1. Abrasion also abets wind erosion.

    磨損作用也助長了風的侵蝕。
  2. Abrasion tests are universally carried out under atmospheric conditions.

    耐磨試驗通常在常壓條件下進行。
  3. Erosion of pipes and vessels from abrasion by particles can be serious.

    由於固體顆粒的磨蝕作用，管子和容器的磨損嚴重。
  4. Tumble abrasion of a fabric is highly dependent on the inherent fiber toughness.

    織物耐滾磨的能力與纖維固有韌度相關密切。
  5. There have been attempts to modify the fiber chemically to resist abrasion enhancement.

    過去曾設法用化學變性方法，提高纖維的抗磨損性能。
  6. For measuring abrasion of catalyst particles, three basic attrition test apparatus are used.

    為了測定催化劑顆粒的磨損，可使用三種基本磨損測試裝置。
  7. For extrudates there are side crushing strength tests, bulk crushing strength tests, abrasion tests.

    對擠條產品有側壓強度的測試，堆積強度測試和耐磨測試。
  8. The fibers with moderate abrasion resistance include wool, cotton, and the high wet-modulus rayons.

    具有中等耐磨損性能的纖維有羊毛、棉花和高濕模量粘膠纖維。
  9. Frosting occurs when two fibers differing in both color and abrasion resistance are combined in a fabric.

    兩種顏色和耐磨損性能不同的纖維組合的織物也會出現霜花色。
  10. Fabrication of high aluminia abrasion - resistent castable

    高鋁質耐磨澆注料的研製
  11. Test method for abrasion resistance of pipeline coatings

    管道塗層耐磨性的試驗方法
  12. Testing method of abrasion resistance of paperboard

    紙板耐磨強度的測試方法
  13. Natural stones - determination of abrasion resistance

    天然石料.耐磨性測定
  14. Footwear - test methods for insoles - abrasion resistance

    鞋靴.鞋墊試驗方法.耐磨損性
  15. Footwear - test methods for outsoles - abrasion resistance

    鞋靴.外底試驗方法.耐磨損性
  16. Test method for abrasion resistance of organic coatings by air blast abrasive

    鼓風磨蝕試驗測定有機塗料耐磨性能試驗方法
  17. The welding performance of homemade wear - resistant cast steel has been studied base on the weldability tests, the repair welding procedures of wean - resistant cast steel ( abrasion - plates ) have been made up, the results show that satisfying repair welding quality can be attained with such welding conditions as the low hydrogenous alkalescent welding rod, preheating and slow cooling, strictly maintaining the interbedded temperature of 250 ~ 300 and controlling welding technique

    通過對其焊接性能的試驗研究，制定了該類鑄鋼件（磨耗板）的補焊工藝：低氫型堿性焊條，預熱與緩冷相結合的工藝措施，嚴格控制層間溫度（ 250 ~ 300 ）及焊接工藝規范，可獲得滿意的修復質量。
  18. The research results show that when the fly ash content is under 30 %, the strength of rcc can be increased but the effect is a little ; and with the fly ash content increased the dry shrinkage of the rcc reduced straightly, and the abrasion resistance and freeze resistance increased obviously. ( 3 ) fly ash can increase durability of the rcc and under the experiment condition, the perfect mixing content is 30 %

    試驗結果表明： （ 1 ）粉煤灰摻量小於30 %時能提高碾壓混凝土強度但影響度不大； （ 2 ）隨著粉煤灰摻量的增加，碾壓混凝土的干縮呈直線降低，且抗磨性和抗凍融能力明顯提高； （ 3 ）粉煤灰能有效提高碾壓混凝土的耐久性，且在試驗條件下的最佳摻量為30 % 。
  19. Determination for attrition and abrasion of fertilizer catalyst

    化肥催化劑磨耗率測定
  20. The research results show that, from the viewpoint of second phase morphologies, there exist quite differences between the grain - type materials ( such as wc / bcu brazing deposit material, wrs1000 and 1zt tungsten carbide strengthening overlaying material, as well as the wear - resistant material of polymer adhesive coating etc. ), and the aggregation - type as well as dispersion - type ones ( such as zg35simn, wrd - 1 and khc - k2 depositing material ) in the wear - resistance and sand slurry abrasion mechanism. the sand slurry abrasion mechanisms are brought forward, of new wear - resistant materials with the features of grain - type second phase morphologies

    研究發現，與聚合型、彌散型第二相的材料（如zg35simn 、 wrd ? 1和khc ? k2熔敷材料等）相比，顆粒型第二相的材料（如wc bcu釬焊熔敷耐磨材料、 wrs1000型耐磨材料、 1zt碳化鎢顆粒增強熔敷材料及ktc ? 1耐磨膠粘塗層材料等）在耐磨性能和磨損機理等方面均有不同，總結提出了以「顆粒型第二相」為特徵的耐磨新材料泥沙磨損機理。
分享友人
分享到 Line

分享到臉書