adjustment plate 中文意思是什麼

adjustment plate 解釋
調整板
  • adjustment : n. 1. 調整；調節（裝置）；校正。2. 調節。3. （賠償損失的）清算。
  • plate : n 1 厚金屬板 〈cf sheet〉 板（片）；（記有姓名等的金屬）牌子，（尤指醫生的）招牌，藏書牌；【印刷...
  1. Move pedal adjustment plate 3 to the right or left until motor control lever 1 is leveled and link rod 2 is vertically positioned

    請左右移動踏板調節板3 ，讓馬達控制桿1和連接桿2呈一直線狀態。
  2. This set of equipment includes : auto - stirring, aerating - and - conveying system, system of automatically sucking cups, oil - blasting system, material - padding system, cloth - spreading system, swerving - and - passing system, system of automatically separating raw material from plates, cooling system, and auot - washing system. additionally, if you replace the mould plate and the die in the equipment of the auto - material plate and give a proper adjustment, you can make various cakes

    全套設備包括：自動攪拌、充氣連體送料系統、自動吸紙杯系統、噴油系統、注料系統、撒布系統、轉彎送盤系統、熱風循環烘爐系統、冷卻輸送系統、轉彎自動送盤系統、自動注料系統、自動料盤分離系統、冷卻系統、烤盤自動清洗系統等組成，該設備只要更換模盤及自動料盤分離設備中模具和適當調整其中設備，就可生產多種花色蛋糕食品。
  3. Based on analysis and comparison of existing test data applied to existing ultimate strength prediction models, interfacial stress at the end of plate is deduced. after formulas for calculating the effective moment of inertia for frp - strengthened beams being revised and adjustment coefficient related to nominal main steel reinforcement ratio and curtailment length ratio being put forward, strength prediction formulas of compound beams under plate end debonding failure are established. in analysis of strength of compound beams under intermediate crack induced interfacial debonding failure mode, several bond strengths and their relation are introduced

    對于板端剝離破壞，在總結現有承載力模型的基礎上，利用已有試驗數據對各承載力計算公式進行了分析比較，進一步採用分階段分析法，推導了板端界面應力的計算公式，在此基礎上，採用加固復合梁有效慣性矩的修正公式，建立了考慮名義配筋率和板端偏移比影響的板端剝離破壞梁承載力的計算公式；對于跨中受彎裂縫導致的粘結破壞，闡述了常見的幾種粘結強度之間的區別和聯系，並基於拉剪粘結強度，提出了跨中受彎裂縫導致粘結破壞的承載力計算公式，並利用現有試驗結果確定了模型中的一些參數；最後，利用試驗數據對本文建立的兩種粘結破壞承載力計算公式進行了檢驗，結果基本吻合。
  4. The factors influencing the regular and irregular longitudinal and transverse misregister were analyzed, and the corresponding solutions to the problems on plate, printing pressure adjustment, tension control of paper tape, printing technology, the machining precision, and installation precision of press were put forward

    摘要針對柔版印刷中有規律性和無規律性的周向套印不準、橫向套印不準故障的影響因素進行了詳細的分析，並從印版、印刷壓力調整、紙帶的張力控制、印刷工藝、印刷機的加工精度和安裝精度等方面提出相應的解決方法。
  5. Taking drawing of tail lamp strength plate in a car for example, the characteristics of drawing complex components with thin steel sheet has been described with some solutions for quality defection during the process of tooling adjustment

    摘要以一款轎車尾燈加強板為例，說明了薄板復雜拉深類沖壓件在拉深時的特點，同時提出了模具調整過程中相關缺陷問題的解決措施。
  6. The pad - lock ? washer system has been improved by incorporating the convex pivot adjustment into the backing plate ; thus allowing for the reduction in the number of washers needed to achieve all spacing requirements

    墊板鎖墊圈?系統已得到改善，納入凸樞軸調整到底板;從而使人數減少后的墊圈，以實現所有間距要求。
  7. Circumscribing the signal adjustment plate, stepping motor drive mold piece, spindle inverter mold piece and i / o mold piece constitute the total hardware construction

    外接信號調理板、步進電機驅動模塊、主軸變頻調速模塊、 i o模塊等構成硬體總體結構。
分享友人
分享到 Line

分享到臉書