aging time 中文意思是什麼

aging time 解釋
成熟期；老化期；老熟期
  • aging : n. 1. 陳釀。2. 熟化。
  • time : n 1 時，時間，時日，歲月。2 時候，時刻；期間；時節，季節；〈常pl 〉時期，年代，時代； 〈the time ...
  1. The effects of main process factors such as feeding mode, reaction ph values, and ratio of ammonia and nickel ion, reaction time, agitation, reaction temperature and aging et al on the crystallization course and physical properties of nickel hydroxide were studied in detail. at last, we acquired the optimal preparation parameters, the spherical nickel hydroxide with high tap density and crystalloid degree, perfect flow ability were prepared

    在研究加料方式，氨水的加入量，反應時間、體系ph值、反應溫度、攪拌、陳化等主要工藝條件對ni （ oh ） _ 2結晶過程和物理性能影響的基礎上，確定了較優的工藝參數，制備出了堆積密度和結晶緻密程度較高、流動性較好的球形ni （ oh ） _ 2 。
  2. 90 % uv below 400nm could be shielded by the nano - sio2 sol. the time of the artificial aging of nano - sio2 - modified coatings prepared by the way of in - situ dispersion method was about twice as long as that of the nano - sio2 - modified coatings prepared by dispersing the nano - sio2 powder in the coating directly. on the other hand, the fadeproof time ( reaching the second level of color aberration ) of the nano - sio2 - modified coatings was 1. 83 times as long as that of the national standard for the super coatings

    實驗證明:納米510 :溶膠具有很強的紫外散射屏蔽性能，對400nm以下的紫外光能屏蔽90 %以上;在位分散法納米510 :改性塗料的耐人工老化粉化時間比直接分散法納米510 :改性塗料提高了近1倍，耐變色時間（達到色差2級的時間）是國標優等品要求的1 . 83倍，較相應的未改性塗料提高了約25 % 。
  3. There was an increase in the fadeproof time of 25 percent over the common coatings. both the nano - tio2 - modified coatings prepared by the way of in - situ sythesising method and the nano - sio2 - modified coatings prepared by the way of in - situ dispersion were strong weatherability coatings, which could resist 18 years " weathering if we calculated the result with the standard which argued that 100h of the artificial aging process was equal

    通過原位生成法制備的納米tio :改性塗料和在位分散法制備的納米510 :改性塗料具有超強的耐候性能，以人工老化100h大約相當于室外曝曬一年計算，納米改性的塗料在室外的使用壽命可超過18年。
  4. Many sandwich generation couples are being stretched to the limit by the necessity of caring for both their aging parents and their children at the same time

    既要照顧年邁的父母，同時又要撫養孩子，許多夾心一代的夫妻因此而緊張不堪。
  5. What the yankees have here, it appears, is a throwback : a one - time ace in the twilight of his career, aging naturally

    目前洋基所有的，看起來就像個回傳球；一個曾經的王牌進入生涯的尾聲，自然的老化。
  6. The time taken to reach maximum hardness decreased and the corresponding maximum hardness decreased with increasing aging temperature. the better properties of al - mg - si - mn - cr alloy were obtained after 8h at 175 ' c. the al - mg - si - mn - cr alloy resembles al - mg - si alloy in the way of the age hardening mechanism

    在同一溫度下，隨著時效時間的延長，合金硬度逐漸上升，在達到時效硬度峰值后又逐漸降低，隨著時效溫度的升高，中南大學碩士學位論文川mg st mn cr合金組織與性能的研究合金達到時效硬度峰值的時間縮短，而相應的時效硬度峰值在減小。
  7. Conclusions ( 1 ) subacute senile mouse model can be used in immunosenesence reseach. ( 2 ) cd 137 may be an marker of aging. ( 3 ) the protection to aicd of cd137 decreased, indicate the function of cd137 was unusual. ( 4 ) the effect of d - galactose can modelling the different stage of aging. ( 5 ) the decrease of cd 137 expression on t cell from subacute senile mouse model and the aging mouse were due to the declining of their mrna. ( 6 ) the expression of cd 137 on t cells from from subacute senile mouse model and the aging mouse have a time dependently derease and the peak of cd 137 expression appeared earlier while the aging keep going on

    結論（ 1 ） d -半乳糖致亞急性衰老小鼠模型t細胞cd137分子表達變化規律與自然衰老小鼠相似，造模兩個月後的大劑量組小鼠即可用於衰老個體cd137分子的相關研究。 （ 2 ）模型小鼠cd137分子表達隨衰老的發生發展呈規律性變化，提示該分子可能為t細胞衰老的分子標志。 （ 3 ）即使在衰老狀態下，機體對cd137分于的表達依然具有調控作用，提示兔疫系統的代償能力仍然存在。
  8. A reliability experiment of thermal aging was carried out for the two types of joints, scanning electron microscopy, energy dispersive x - ray spectrometer and micro x - ray diffractomer were adopted to investigate the interfacial evolution behavior of joints, and kinetics model of imc formation was established. the results show that imc growth follows the parabolic law as a function of aging time at certain aging temperature, imc growth is more sensitive to the aging temperature than the aging time, the activation energy of cu - al imc growth is 97. 1kj / mol and the major forming cu - al imc are cual2 and cu9al4, the activation energy of au - al imc growth is 40. 1kj / mol and the main au - al imc are au4al and au5al2, with au2al and aual at the interfacial periphery of joints, the rate of cu - al imc growth is about 1000 times slower than that of au - al imc, and kirkendall voids and cracks are easily appeared during thermal aging in gold ball bonds while voids and cracks are absent in copper ball bonds even after aging at 200 for 2900 hours and 250 for 169 hours

    研究結果表明:金屬間化合物厚度與老化時間的關系符合拋物線法則，金屬間化合物的生長對老化溫度比老化時間更加敏感; cu - al金屬間化合物生長的激活能為97 . 1kj / mol ，老化后金屬間化合物呈層狀分佈，主要相為cual2和cu9al4 ; au - al金屬間化合物生長的激活能為40 . 1kj / mol ，主要相為au4al和au5al2 ，同時在界面周邊區域生成了au2al和aual ;老化過程中cu - al金屬間化合物生長速率比au - al金屬間化合物生長速率小103數量級;金絲球鍵合點200老化96小時出現了明顯的kirkendall空洞和裂紋，但銅絲球鍵合點200老化2900小時和250老化169小時都沒有形成空洞和裂紋。
  9. The useful life curves of gan - based blue led with al2o3 and sic substrate is fit single exponential function [ i = i1 + i2exp ( - t / ) ]. fron this function, we could get aging information of led about stable inteneity 1, decay intensity i2 and decay time. the novel method of evaluating aging properties of leds was put forward

    用單指數函數擬合了發光二極體的光衰減曲線[ i = i _ 1 + i _ 2exp （ t / ） ] ，這個關系式可以給出三個信息：穩定光強、衰減光強、衰減速度，提出了更加合理的評價led老化性能的方法。
  10. At the same time, the results show that the minimum pd quantity and its discharge numbers also add along with the aging time increasing. and the craggedness degree of - q figure of pd becomes steep along with ageing time too

    局部放電的最小放電量隨著老化時間的增大其值也逐漸增加，而且放電次數也不斷增加，因此，這也可以作為一個特徵量來進行絕緣監測。
  11. The peak of cd 137 expression on t cells from aging mouse appeared earlier compared with normal, and the appearance of the early peak was time dependently with aging. ( 2 ) the expression pattern of cd137 from subacute senile mouse was similar to that of the aging mouse. ( 3 ) the death ratio of t cells from aging mouse were higher than that of the normal level. ( 4 ) mrna of t cells from aging mouse and subacute senile mouse was decreased, and mrna from t cells of model mouse seem have a lower quantity than the aging mouse

    提取總rna ，應用rt - pcr方法檢測cd137的mrna水平變化。結果（ 1 ） d -半乳糖致衰老模型小鼠和自然衰老模型的脾臟t細胞上cd137分子表達水平低於正常水平，表達高峰提前出現，隨后表達水平下降遲緩。 （ 2 ）在造模過程中，亞急性衰老模型小鼠cd137分子表達水平逐漸降低，分子表達峰逐漸前移。
  12. In the third chapter, the influence of current density, solution concentration, erosion time and aging in ambient air on the pl spectra of ps suggests that peak would blue shift with current density increasing, and with erosion time and aging time prolonging ; with the increasing of solution concentration, peaks would red shift when solution concentration less than 1 : 1 but blue shift when solution concentration greater than 1 : 1. above phenomena can be explained by quantum confinement and light center model, but do not deny the action of si - h bonding and defect on the surface in the process of photoluminescence. at present, radiation mechanism is still one of the primary problems in the study of ps

    在第z三章中；通過對比，分析了電流密度、陽極化時間、溶液濃度以及自i然氧化時間對多孔硅光致發光光譜的影響，認為在一定的范圍內，多i孔硅的發光峰位會隨電流密度的增大而藍移，要獲得較強的發光，需z要選擇合適的電流密度；隨著腐蝕時間的延長，多孔硅的發光峰位會i發生藍移；當f酸的濃度較小q ： 1 ）時，峰位隨濃度的增大表現為向i低能移動；而當f酸的濃度較大河山時，峰位隨濃度的增大則表現z為移向高能；多孔硅在空氣中自然氧化；其發光峰位發生藍移，而強i度隨放置時間的延長而降低。
  13. This paper introduces the aging theory that can be used in the production of workstation, and points out that the rate of the unqualified product is influenced by the setup of the aging time

    摘要本文介紹了服務器生產過程中，老化拷機這個生產工藝過程的理論，說明了老化時間設定對產品出廠不良率水平的影響及老化時間的推算方法。
  14. It was found that the linear characteristic of two kinds of conductive silicone rubber was improved with the increase of aging time

    結果表明， 2種線性導電硅橡膠的線性特性是隨自然老化時間的延長，其線性提高。
  15. Theory analysis and experimental results show that the rate of the unqualified product can be decreased and the life time can be lengthened when the aging time, set scientifically

    理論分析與試驗數據都表明，科學設定老化時間，對降低服務器產品的出廠不良率，提高服務器產品的使用壽命都起著關鍵性作用。
  16. The influences of w0 ( molar ratio of water to surfactant ), the concentration of the reactants and the aging time on the morphologies and the sizes of the nanoparticles were studied

    研究了微乳液中水與表面活性劑的摩爾比（ _ 0 ） 、反應物濃度及濃度比、陳化時間等條件對產物形貌的影響。
  17. Results show that when the ratio of the ion concentration is 1. 707, ph of the reaction is 10. 0, reaction temperature is 45 and the aging time is ih, the ultra fine mn - zn ferrite precursor particle can be obtained

    得到粒度最小的參量值如下：離子濃度比為1 . 707 ，溶液ph值為10 . 0 ，水浴溫度為45 ，陳化時間為1h 。
  18. In order to obtain the mn - zn ferrite precursor particle which has itra - fme property, the optimum technological condition was obtained through the orthogonal experiments in this paper. in the co - precipitation procession of preparation the leading factors that affect the size of the particle are ratio of the ion concentration ( a ), ph of the reaction ( b ), temperature of reaction ( c ), and aging time ( d )

    本文通過拉丁正交試驗，以粒徑尺寸為考察目標，將離子濃度比（ a ） ，反應ph值（ b ） ，水浴溫度（ c ）和陳化時間（ d ）作為四參量，利用每一參量為變量進行試驗確定各參量值，從而確定製備超細錳鋅鐵氧體前驅體粉末的條件。
  19. According to the general principles of biomineralization, we used many functional organic templates, which can efficiently interact with caco3 crystal, to control the crystal form and the morphology of caco3. many systematic studies o f the influence of various experimental parameters, such as ph of solution, concentration of additives and caco3, temperature, aging time, etc., on the morpho - logy and size of caco3 crystals are investigated

    我們系統地分析了各種實驗參數，例如溶液的ph值、有機大分子的濃度、碳酸鈣的濃度、環境溫度、陳化時間等對碳酸鈣粒子形貌及大小的影響，合成出了一系列具有奇異形貌的碳酸鈣材料，豐富了碳酸鈣形貌的種類，並對這類材料的礦化機理進行了較深入的研究。
  20. At the same time, isothermal aging and impact testing are used to study the variations of impact energy ak with aging time of the sn - doped steel

    同時，採用等溫時效和沖擊等試驗方法研究了含sn低碳鋼在保溫過程中沖擊功a _ k隨時間的變化規律。
分享友人
分享到 Line

分享到臉書