air jet velocity 中文意思是什麼
air jet velocity
解釋
空氣射流速度-
We can use the mm5 model in definite time, definite area weather forecasting. we conclude that : : the moving route of this necw in its developing progress was direct - south along latitude, the cold air is rough, and just this made the rough vertical velocity ; the necw southern moving and conflicting with the west pacification sub - tropical high makes rough jet steam. the plenty south - west warm and wet air made by the jet stream gave the rainstorm demanded vapor ;. the rough vertical velocity by jet stream is a main reason in this rainstorm ; the mm5 model uses four - direction analysis data as its input, this avoids some errors occurred in observe and transfer, thus made the result more useful
綜合分析認為： （ 1 ） 、這次冷渦在其發生發展過程中，其移動路徑是沿經圈直線南壓，攜帶的冷空氣勢力較強，形成槽后較強的垂直運動； （ 2 ） 、西太平洋副熱帶高壓偏北位置與東北冷渦南壓形成的急流軸，把源源不斷的西南暖濕氣流輸送到遼西地區，也就是急流軸的左前方位置，為這次暴雨的產生提供了充足的水汽來源； （ 3 ） 、低空急流不但為暴雨輸送水汽，其造成的較強的垂直環流也是產生強降水的一個主要原因； （ 4 ） 、 mm5模式以四維同化資料作為初始場，最大限度地避免了觀測誤差可能造成的積分不穩定，提高了模擬結果的參考價值。 -
Air is entrained as water jetting into water cushion pool, the gas - liquid two phase flows field are formed. the every phase velocity field are measured by using piv and ptv ( particle tracking velocimetry ) method in the course of jet angle 75and60 in gas - liquid flows of water cushion pool. image house of two phase flows are set up
西安理工大學碩士學位論文使用數字圖像處理技術中的piv和ptv測速技術就射流入水角75度和60度兩種情況分別測量了水墊塘模型水氣兩相流流場的各相速度場，建立了相應的兩相流流態圖像庫。 -
A reasonable position of driving nozzle helps to achieve the maximum material flow that also depends on other parameters such as backpressure, properties of conveyed material and driving gas. it is observed that, an increase of convergent section angle is harmful to the pneumatic conveying system, and also influences on the mass flow rate of conveyed material, the distribution of static pressures in injector and the pressure drops of conveying pipe. in addition, within a reasonable scope of air mass rate, increasing the driving jet velocity is more advantageous than enlarging the dimension of driving nozzle
試驗研究發現，氣體噴嘴位置對氣固噴射器的輸送能力影響最大，氣體噴嘴存在某一最佳位置，而這一最佳位置與背壓、輸送物料特性和輸送風特性相關聯；氣固噴射器的收縮角對其輸送能力、內部靜壓分佈和輸送管阻力特性均有適量影響，收縮角增大對整個輸送系統均不利；在適當的輸送風范圍內，提高氣體噴嘴出口速度比擴大氣體噴嘴尺寸更為有利，但氣體噴嘴出口速度過高會增加氣固噴射器和輸送管內的能量損耗，給輸送帶來不利的影響；系統背壓與氣固噴射器的氣體噴嘴出口速度的選取有關。 -
The ratio of the length to the depth of scour hole decreases with the increasing scour depth, in spite of the reason is the increase of the air concentration, the decrease of the jet velocity or the decrease of the jet thickness. 5. governing equations of the aerated jet flow are established
摻氣對沖坑形態並沒有實質性的影響，沖坑的寬深比隨沖坑深度的減小而增大，無論造成沖坑深度減小的原因四） 1大學i學博士學位論文是摻氣、降低流速還是減小入射水舌厚度，其變化規律都可用相同的直線關系表示。
分享友人