air oxidation process 中文意思是什麼

air oxidation process 解釋
空氣氧化法
  • air : n 1 空氣，大氣。2 天空，空中。3 微風，和風。4 態度，樣子，風度，氣派；〈pl 〉高傲的架子。5 傳播，...
  • oxidation : n. 【化學】氧化（作用），正化。
  • process : n 1 進行，經過；過程，歷程；作用。 2 處置，方法，步驟；加工處理，工藝程序，工序；製作法。3 【攝影...
  1. Emtric exhibits good oxidation stability even under the conditions of elevated temperatures at the spark gap and exposure to air found in emtric process

    Emtric具有極佳的抗氧化性，使得它在放電間隙的高溫與曝氣環境下，仍能保持穩定。
  2. Experimental parameter was optimized in synthesizing cnts process and the temperature and time for the air oxidation were ascertained

    通過反復實驗優化制備實驗參數，並確定了空氣氧化提純的溫度和時間。
  3. Bell type furnace is mainly used to steel strips, steel plantes, copper strips, copper plates and other metal parts for bright anneal and normal anneal heat treatments. according to the technics, the process of preevacuation. heating, protecting atmosphere gew or non oxidation heating, air cooling, fast colling and slow cooling treaments can be executed

    罩式爐主要是用於鋼帶、鋼盤圓、銅帶、銅盤圓及其它金屬材料及零件的光亮退火和一般退火工藝，根據熱處理工藝的要求，可對熱處理工件進行預抽真空、加熱、保護氣氛少無氧化加熱、空冷、快冷及緩冷處理。
  4. A process approaching 3 - and 4 - chlorophthalic anhydride in high purity via chloriation of o - xylene, oxidation of monochloro - o - xylene by air in gas phase, and separation of 3 - and 4 - chlorophthalic anhydride afterwards by distillation is described

    摘要介紹由鄰二甲苯氯代，再經空氣氧化及異構體分離合成氯代苯酐中試規模的合成路線。
  5. In chapter three, the mechanism responsible for scanning probe field - induced oxidation in ambient air is attributed to an electrochemical process, i. e., anodic oxidation or anodization, after the analyses is given of a surface of a sample exposed to air. the effects of biases, tip speeds on morphology of field - induced oxidation, are introduced and deduced in the form of kinetics formula of oxidation growth

    第三章首先通過分析大氣環境下掃描探針場致氧化加工的基本特性，得出掃描探針場致氧化的加工機理為電化學陽極氧化反應；引進大氣狀態下場致氧化的動力學方程，推導出偏置電壓與場致氧化物的幾何形態兩者之間的關系、掃描探針移動速度與場致氧化物的幾何形態兩者之間的關系。
  6. Ground on the knowledge of the form mechanisms of the coating defects, the research work proposed some thoughts related to preparation / deposition process to control the coating defects. based on observation of micro - morphologies of the coatings, combined with relative weight change in oxidation, the effects of these modifications on coating defects control and the behaviors of 2d c / sic at constant temperatures in air condition were investigated. the main contents and conclusions are as follows : 1

    本文從多層cvdsic塗層缺陷形成的根源出發，通過塗層制備工藝進行塗層缺陷控制；以對塗層顯微形貌的觀察為基礎，結合氧化重量變化率，研究了不同塗層改性工藝對多層cvdsic塗層面缺陷的影響以及對2dc sic復合材料恆溫氧化行為的影響，主要研究內容與研究結果如下： （ 1 ）研究了多層cvdsic塗層的2d和3dc sic復合材料在空氣中的恆溫氧化行為，表明2d和3dsic ? c sic在空氣中表現出類似的氧化動力學行為。
分享友人
分享到 Line

分享到臉書