air-inlet system 中文意思是什麼
air-inlet system
解釋
進氣道系統-
Brief introduction for gas turbine inlet air cooling system
淺述燃氣輪機的進氣冷卻技術 -
Second, the starting and stopping behaviors under disturbed condition are analyzed and calculated by using the dynamic concentrative parameter model, which gives some advice to better prescribe refrigeration system and set theoretic foundation for carrying out automatic control of refrigeration system. third, the normal running process is analyzed and calculated by means of rational matching theory, which gives some advice on how to better understand the parameter change under steady state and the affection of inlet - parameter on evaporator. fourth, the simulation software with dynamic characteristic is designed, which can be applied to calculate thernio - parameter of cryogen, air humidity and frost thickness under different initial and boundary conditions, and to carry out dynamic simulation under conditions of dryness, wetness and frostiness, at the same time, to achieve detection and simulation at any stage from starting to stopping
本文的主要內容如下： 1 ）對翅片管蒸發器結構特點進行分析，選取適當的微元控制體，就干、濕和霜工況下對每個微元分別進行傳熱傳質分析，基於經驗關系式確定霜的有關參數，對于霜工況下的霜生長建立模型，經適當假設，運用質量守恆、能量守恆和動量守恆方程建立適合動態模擬的蒸發器數學模型，為系統模擬奠定基礎； 2 ）對蒸發在大擾動下的開、停機過程，運用動態集中參數模型進行分析和計算，為更好地描述製冷系統運行的全過程奠定基礎，同時也為製冷系統實現自動控制提供一定的理論基礎； 3 ）對蒸發器正常運行過程，運用動態分佈參數和參數間定量耦合的觀點來分析和計算，為更好地了解穩態工況下各點參數的變化情況及各入口參數對蒸發器動態特性的影響即蒸發器性能對各參數變化的敏感性； 4 ）編寫翅片管蒸發器動態特性模擬計算程序，可以計算不同邊界條件和初始條件下的製冷劑熱力參數、空氣溫濕度和霜厚度分佈場，實現對翅片管蒸發器在干、濕和霜工況下的動態模擬。 -
Realization of the economical evaluation system for gtcc inlet air cooling based on numerical integration
進氣冷卻經濟評價系統程序實現 -
Thirdly, radiator performance test - bed thermal system control modeling and rule self - organizing fuzzy control simulation were studied. the water supply temperature, radiator inlet temperature, test room temperature based on water temperature regulation, air supply average temperature and test room temperature based on air temperature regulation total five controlled processes transfer function were set. finally, rule self - organizing fuzzy control simulation for two
通過試驗，辨識了散熱器實驗臺熱工系統中供水溫度、散熱器進水溫度、基於熱水系統調節的測試室溫度、送風平均溫度及基於送風系統調節的測試室溫度共5個被控過程的傳遞函數，並對基於熱水系統調節和基於送風系統調節的測試室溫度響應過程進行了規則自組織模糊控制模擬。 -
Great difference in pressure for two flow made pressure wave system and it help to extend the delay time for gas in chamber, which increases combustion effusion. second, to increase combustion effusion, the inlet temperature of air and gas should be enhanced in the range of heat releasing in chemical reaction. third, the first work condition is unburned absolutely and the second work condition is burnt in shear layer of inlet and the end of down wall zone in straight segment
對于壓力差很大的兩股氣流，所形成的壓縮波系的結構可以增加燃氣駐留時間，提高燃燒穩定性;為了提高擴散燃燒的效率，在保證能放熱的化學反應溫度范圍之內，應適當提高燃氣及空氣的來流入口溫度;燃氣噴嘴應居於燃燒室軸線上，是改進超音速燃燒室結構的一種思路。 -
There is no thoroughly rounded theory about displacement ventilation system in our country at present and our research begins recently. the study work of this paper will be useful for further optimization design of displacement ventilation system. this dissertation includes five parts. the first part introduces the development of the displacement ventilation and the background of research in domestic and oversea. in the second part, it gives working principle of displacement ventilation system and it ’ s advantages to the mixture ventilation. the study also gives a series of indexes to evaluate displacement ventilation system and specifies air supply terminal device and so on. it is needed to simulate and analyse the velocity field, temperature field and distribution of flow field. this is the third part. the forth part specifies the simulative method for thermal stratification of displacement ventilation system. it gives some factors affecting thermal stratification height such as inlet temperature, inlet velocity, heat transfer of wall body, distance of heat source and so on
本文的研究工作主要包括以下幾個方面的內容: （ 1 ）綜述了國內外相關的研究現狀和研究背景; （ 2 ）簡介了置換通風的工作原理，並分析了它相對于混合通風的優良特性及評價指標、末端裝置等; （ 3 ）對採用置換通風方式房間的溫度場、速度場和氣流分佈進行了模擬計算與分析; （ 4 ）對採用置換通風方式房間的熱力分層高度進行了模擬計算，並分析其影響因素，如:送風溫度、送風速度、圍護結構傳熱和熱源分佈等; （ 5 ）擬合了無量綱熱力分層高度相應于送風溫度t 、送風速度v 、熱源間距離l和圍護結構傳熱q的經驗公式。 -
Air - inlet system
進氣道系統 -
The emission control system incorporates both inlet port ， induced air motion and compression ， induced turbulence for fast and complete combustion
可譯為：發射（或推進）控制系統混合來自進氣口的空氣，引起空氣運動和壓縮，並引發空氣湍流以加速並完全燃燒。 -
Talking about the inlet air heating system of pg9351fa gas turbine
燃氣輪機的進氣加熱系統 -
The test simulation system include simulation cabin, air inlet system, exterior ambient simulation system, indirect pneumatic pressure regulator and data acquisition system
整個試驗內容包括壓力調節器阻力特性試驗、車外壓力為負壓時的靜態試驗、車內壓力為正壓時的靜態試驗及車外壓力變化的動態試驗。
分享友人