air-spraying 中文意思是什麼
air-spraying
解釋
飛機噴霧-
We soon realized that the black mark was baba grugru oil spraying up into the air above the derrick.
不久我們就意識到那黑色的東西正是噴過井架射入高空的巴巴古爾古爾的石油。 -
The structure of air - blast pipe was improved on. an orienting object was installed based on theoretical analysis, that increase the spraying span. it has been found that both spraying span and droplets uniformity improved, by installing the orienting object. according to the results of a great number of experiments, orderliness of droplets diameter along the spraying span was researched, and rational spraying span of air - assisted sprayer was suggested
通過試驗檢驗噴霧機樣機的噴霧性能，並提出對各項參數的優化設計方案。通過正交試驗和對比試驗對霧滴取樣，證明導流器的安裝不僅增加了噴幅，而且還提高了霧滴均勻性系數。根據大量試驗的結果分析，找出了霧滴直徑在噴幅方向上所呈現的變化規律，並提出了合理的噴幅范圍。 -
Through the special studies on impacts to atomizing and humidifying effect from such factors as the firing pin type, centrifugal structure, higher spraying pressure, less aperture, initial water temperature and original state of the air, some conclusions are obtained, such as : the centrifugal nozzle with firing pin type, high pressure and little aperture has bigger air eddy and atomizing angle. the spaying liquid has high velocity. the droplet is small, and the heat and mass transfer velocity is high
通過對撞針型結構、離心式結構、較高的噴水壓力、較小的噴嘴孔徑、噴水初溫及待加濕空氣初狀態對霧化加濕效果的作用原理的重點分析，得到：撞針型高壓小孔徑離心式噴嘴具有較大的空氣渦與霧化角，噴出的液體流速高、液滴小、水與空氣傳熱傳質速率高，撞針型結構提高了霧化加濕效率，高壓小孔徑的特點為霧化加濕提供了較大的能量，而噴水初溫的升高會減小水的粘性力和表面張力，從而優化加濕效果。 -
The characteristics of high pressure gyratory sprayed pumping discusses is presented, which is applicable in wide range of scope and ground layers, convenient for construction, long durability, wide source of materials. mechanism for subgrade strengthening : complex foundation of cement solid and earth between piles was formed by pulsant load of flowing pressure and spraying flow, water wallop, cavitation phenomenon, water wedge effect, extrusion force and air flow agitation etc so as to enhance foundation bearing force and reduce settlement and deformation
高壓旋噴注漿技術具有適用范圍、適用地層較廣，施工方便，耐久性好，材料廣闊等特點；其加固地基機理主要是通過流動壓、噴射流的脈動負荷、水塊的沖擊力、空穴現象、水楔效應、擠壓力、氣流攪動等效應形成水泥固結體與樁間土的復合地基，從而提高地基承載力，減少沉降變形。 -
Was established in 1996, grows fast as the development of the econnomy, we mainly research, develop and produce plastics, metal dustless coating macbine, transmission equipment, cprintedilk production line and all kinds of nonstandard industrial equipments, such as automatic constant temperature and constant humidity uv ray solidified production line, we also provide automatic electrostaric cleaning system and reciprocator, and piastic of coating cine mobile phone, camera, pda, dvd. stereos coating line, single or double core - strained powder - recycling system, full stainless steeled spraying. overflowing pre - treatmentsystem, gas or oil combustion machine, electric heat drying stove, workshop cleaing, air supplier cleaning equipment etc
其中包括恆溫恆濕及全自動uv光固化生產線；全自動靜電除塵設備系統及往返系統；手面、相機、掌上電腦、 dvd 、多媒體音箱等塑膠外殼塗裝生產線『單、雙回收濾芯式粉體系統；全不銹鋼噴淋式、游浸式前外理；燃氣、燃油、電熱風烘乾爐；凈化車間、凈化供風設備等。 -
Spraying method whether by air spray, airless spray, hot air spray or hot airless spray should be in accordance with the following
空氣噴塗，無空氣噴塗，熱空氣噴塗或無空氣熱噴塗均應遵循以下原則。 -
The condensed water separated from the air - conditioning system of an airplane is sprayed in the cold side of the radiator, and the heat transfer and the state change of water in the process of its spraying to the ram air are analyzed
摘要將飛機空調系統中水分離器分離出的游離水噴到散熱器的冷邊，並對水噴到沖壓空氣中的狀態變化過程和傳熱過程進行分析和計算。 -
The total area of the corporation covers about 200 chinese acres and the length of coastline is about 1, 140 meters, the auxiliary facilities have taken shape the main facility and the equipment include the 30, 000 dwt dry dock which is 192 meters long by 40 meters wide the gate width 32 meters and 10 meters deep, is to date the biggest dry dock in fujian province ; one fitting wharf length 65 meters, width 17 meters ; 16 tons portal crane 1 set, 16 tons gantry crane 1 set, mobile cranes 50t1 25t1 12t2 8t4 and other necessary transportation, coatings, the precision work equipment supplying air 120 m min, spraying grit more than 4, 000 m day, renews the steel plate 12 15 t day we can finish repairing all kinds of ships under 40, 000 dwt within 7 to 10 days our corporation obtains the first - class dockyard to repair and build steel - made ships lisence in 2001, passed the national environmental protection appraisal in august 2002, was designated shipbuilding in fujian for maintaining foreign ships in octobet 2002, the dry dock, passage channel, the turning area, fitting wharf are passed by passage safety appraisal in march, 2003
主要設施和設備有： 3萬噸級干船塢一座長192米寬40米塢門凈寬32米深10米是福建省目前最大的干船塢舾裝碼頭一座長65米寬17米16噸門座起重機1臺10噸門吊1臺汽車吊8臺50噸1臺25噸1臺12噸2臺8噸4臺以及與其相配套的運輸噴塗精加工設備。每分種供氣120立方米，日噴砂面積4000多平方米，日換鋼板15 20噸。一般修船工期為7 10天。 -
As to the work about experiment study, at first, the paper makes certain the prominent affecting factors to the automating and humidifying property of this kind of nozzle by orthogonal experiment. by jicha analysis method and fangcha analysis method, the paper got that the nozzle aperture, the initial water temperature and the spraying pressure have prominent effect to the humidifying property while the effect of the original air state is small
試驗工作方面，首先通過正交試驗確定對撞針型高壓小孔徑離心式噴嘴霧化加濕性能影響顯著的因素，運用極差分析法和方差分析法，得到噴嘴孔徑、噴水初溫和噴水壓力對噴嘴的加濕性能影響顯著，而待加濕空氣初狀態的影響相對較小。 -
Later, the paper ascertains how the prominent factors influence the humidifying effect by single factor experiment and got such solutions : when other situations do n ' t change, the nozzle flux will enhance with the increase of the nozzle aperture and spraying pressure. air ' s changing quantity of enthalpy and absolute humid, valid humidified quantity, humidifying efficiency and saturation efficiency will enhance with the increase of the initial water temperature. with the enhance of the praying pressure, the valid humidified quantity and air ' s changing quantity of enthalpy will increase first and decrease later, while the humidifying efficiency will drop
然後通過單因素試驗確定影響顯著的因素如何作用加濕效果，得到：在其他條件不變的情況下，噴嘴流量隨噴嘴孔徑和噴水壓力的升高而增大，空氣焓變量、絕對濕度差、有效加濕量、加濕效率及飽和效率隨噴水初溫的升高而提高，有效加濕量和空氣焓變量隨噴水壓力的升高先增加然後有所下降，而加濕效率隨噴水壓力的升高而下降，焓變量和絕對濕度差隨水氣比的增加而增大。 -
To research the energy transformation and utilization orderliness of the new proposed system is the main objective and content of this dissertation, as follows : about two thirds of the work output of the turbine is consumed by the compressor. traditionally, every way of inter - cooling adopted in gas turbine decreases the work consumption of compressor in some degree. through the spraying of water at the entrace of compressor, the air can be continuously cooled in compression so that the work consumption can be reduced greatly
本論文從以下幾個方面進行了研究：由於燃氣輪機循環中壓氣機消耗近2 3的透平出功，傳統上採用的各種間冷方式都一定程度地降低了壓氣機耗功；而壓氣機入口採用注水方式，可以對壓縮空氣進行連續冷卻，以達到大幅度降低壓氣機耗功的目的。 -
Silvery white, powder spraying aluminum alloy, doors and windows aluminum shaped materials, four rush pith stick shaped materials, cold storage reveal cupboard shaped materials, radiator shaped materials air conditioner, solar energy, furniture, carpentry machinery and so on, various kinds of aluminum shaped materials
各種系列銀白色、靜電噴塗鋁合金、鋁合金門窗型材，裝飾材料、酒類包裝型材、純鋁型材、電信四芯棒型材、冷藏展示櫃傢具、木工機械等各種工業型材。 -
Spraying urethane foam for blocking air leakage in the area of roadway roof fall in wangcun coal mine
王村礦煤巷高冒區聚氨酯泡沫堵漏風技術 -
Aimed at some problems such as short spraying distance, electricity - leaking and reverse ionization among electrostatic nozzles existing in the country, a induction charging and pneumatic energy electrostatic nozzle was designed. the basic designing theories, structure and working process of this nozzles were theoretically specified in the paper. and then the atomization quality and charge performances of this nozzle and its affecting factors were studied by carrying out performance experiment and statistic analysis. result of the studies indicate : ( 1 ) some progress were made in solving the problems list above ; ( 2 ) from this nozzle, droplet were minute and uniform, and higher charge - mass ratio can be obtained under lower electrostatic voltage, thus the atomization quality and charge performance of this nozzle were both better ; ( 3 ) within the experiment extend, air pressure at 0. 2mpa, electrostatic voltage at 2400v were the most suitable parameters for the nozzle ; ( 4 ) the regression equations for describing droplet size, intensity of spray current and charge - mass ratio of this nozzle obtained from the experiment data had higher forecast precision ; ( 5 ) cross - effect of all factors were not significant, the atomization quality and charge performance were relative dependency affected by the factors
諸試驗因素中，充電電壓和噴孔直徑對霧滴荷質比均有極顯著的影響；氣體壓力和液體流量對霧滴荷質比的影響均不顯著；影響霧滴荷質比的主要因素依次為充電電壓和噴孔直徑; （ 8 ）在300v 、 600v 、 1200y 、 1800y 、 2400v 、 3000v六種充電電壓t ，霧滴荷質比先隨充電電壓的增加而增大， 2400v后荷質比減小，推測:對于所研製的噴頭可能存在一個最佳充電電壓; （ 9 ）由充電電壓和噴孔直徑的不同搭配所得霧滴荷質比不同這一結果，可看出，較大充電電壓需配備較大噴孔直徑以增強霧滴荷電效果; （ 10 ） td3 . 6和td3 . 4兩噴頭的霧滴荷質比曲線趨于重合，說明噴孔直徑大於滬3 -
This type of dryer was fitful for liquid drying in concurrent, counter - current or mixed air - flow. the dryer can produce powders, granules, hollow spherical particles and agglomerates products. the spraying capacity and particle size were changed by altering the parts assembled in the nozzle
壓力噴霧乾燥裝置其霧化器的結構適用易調，可通過改變噴嘴的內部結構得到所需要的噴液量和霧滴尺寸，目前該型式乾燥機已推廣應用於食品、化工、醫藥、建材、環保等行業。 -
Oil - water separator is attached to gas and electric spraying equipments. it is used for filtering compressed air and absorbing moisture to ensure good coating quality
空氣濾清器是氣噴槍、電噴槍的配套設備之一，它具有對壓縮空氣進行過濾和乾燥作用，從而保證塗層質量。 -
High - pressure blasts of compressed air then turned the brain into a slurry that squirted out through the same hole in the skull, often spraying brain tissue around and splattering the hose operator in the process
然後，由壓縮空氣形成的高壓氣浪會將豬腦吹成腦漿，並同樣從枕大孔處噴濺出來? ?從事這個操作程序的時候，豬腦通常會四處噴濺，並濺射到操作者的身上。 -
As a main product of our company, spraying drying set is a kind of centrifugal or pressurized, which atomizes liquid materials such as solution, suspension, emulsion or paste into timy droplet ( surface area increased ) and dry them into powder product an once ( several to dozens of seconds ) by contacying hot air
噴霧乾燥機組是一種用離心式或壓力式霧化器，將溶液、懸浮液，乳濁液或漿料等料液霧化成細微液滴（表面積顯著增大） ，經與熱風接觸得以急速乾燥（幾秒到幾十秒） ，從而直接得到粉末產品的裝置。 -
3the spraying technique has strict process requirement on interior decorative materials. under specific circumstance, ethoxyline or polyester, via their thermosetting property, is converted into modified epoxy i. e. high molecular material so as to obtain the advantages such as smooth surface, uv resistance and air pollution resistance
3噴塗技術對室內外裝飾材料的工藝要求極高，環氧樹脂或聚酯通過熱固性使其環氧樹脂或聚酯能在特定的條件下得到充分的反應，轉化成改性環氧即為高分子材料達到表面平滑抗紫外線，抗空氣污染等特點。 -
If spraying application is carried out in a limited place like narrow booth, the operator must wear a ventilated mask with an air compressor for feeding filtrated fresh air
如果噴塗施工是在狹小艙室內等有限空間進行時，必須佩戴通風面罩，以空壓機不斷送入經過濾處理的新鮮空氣，以供操作者呼吸之用。
分享友人