amplifier stability 中文意思是什麼
amplifier stability
解釋
放大器穩定度-
This paper starts the research of the liquid floated pendulous accelerometer testing system according to the engineering. at first, this paper gives the brief introduction of the history and present status of accelerometer and its testing technology, the working principium and math model of the liquid floated pendu - lous accelerometer, and then, decides the binary width pulse force retrim loop as the design proposal of testing system, researches the transfer function of every part in the system emphasizly, analyses the stability of the whole accelerometer testing system from the angle of control theoretics by the open loop transfer function of system, and designed the correcting net, analyses the basal problems such as resolution, sampling restraint, precision and so on, designs the hardware testing circuits such as preamplification, band - pass filter, alternating amplifier, phase sensitive demodulatorn, pulse - width modulation, frequency scale circuit, moment current generator. finally, using the graphics program language labv - iew which is designed for testing field especially by ni accomplishes the solfware design of testing system, realized the testing functions
首先對加速度計及其測試技術的發展歷史和現狀，液浮擺式加速度計的工作原理和數學模型等作了簡要的介紹，然後確定了以二元調寬脈沖再平衡測試迴路為設計方案，並從控制理論的角度進行了分析，著重研究了系統中各部分的傳遞函數，利用系統開環傳遞函數分析了系統的穩定性，同時設計了系統的校正網路;分析了二元調寬脈沖再平衡測試迴路的解析度、采樣約束以及測試精度等基本問題，並按照系統分析的結果設計了包括前置放大、帶通濾波、交流放大、相敏解調、脈寬調制、頻標電路以及力矩電流發生器等測試系統各部分硬體電路，驗證了電路的正確性，最後按照測試系統的要求，採用了美國ni公司專為測試領域所開發的虛擬儀器工具? ? labview作為測試軟體開發工具，利用該圖形化編程語言完成了測試系統軟體部分的設計，實現了測試功能。 -
The innovation of the dissertation is indicated as follows : in the discussion of the ctrl _ gm sub - block, the transconductance stability of operational transconductance amplifier is deeply studied
本論文的創新之處在於:在對ctrl _ gm模塊的論述中，論文對運算跨導放大器（ ota ）的跨導穩定性進行了較為深入的研究。 -
Feedforward is generally known as the best performing linearization technique for its advantages, such as broadband, stability, etc. this paper introduces the theories of power amplifier nonlinear characters and feedforward technique. according to the rf specifications in 3gpp for wcdma transmitter power amplifier, an adaptive feedforward amplifier system is completed including eda simulation, circuits layout and main mechanical structure design
本文根據3gpp對wcdma發射機功率放大器的射頻指標要求，在對功率放大器的非線性特性和前饋技術的特性進行詳細理論分析的基礎上，結合eda模擬工具，設計了基於自適應前饋的功放系統，並完成了系統的調試和測試。 -
The thesis has done the widespread investigation and study to the domestic and foreign ’ s technologies of analogy low voltage and low power, and analyzes the principles of work, merts and shortcomings of these technologies, based on the absorption of these technologies, it designs a 1. 5v low power rail - to - rail cmos operational amplifier. when designing input stage, in order to enable the input common mode voltage range to achieve rail - to - rail, it does not use the traditional differential input pair, but use the nmos tube and the pmos tube parallel supplementary differential input pair to the structure, and uses the proportional current mirror technology to realize the constant transconductance of input stage. in the middle gain stage design, the current mirror load does not use the traditional standard cascode structure, but uses the low voltage, wide - swing casecode structure which is suitable to work in low voltage. when designing output stage, in order to enhance the efficiency, it uses the push - pull common source stage amplifier as the output stage, the output voltage swing basically reached rail - to - rail. the thesis changes the design of the traditional normal source based on the operational amplifier, uses the differential amplifier with current mirror load to design a normal current source. the normal current source provides the stable bias current and the bias voltage to the operational amplifier, so the stability of operational amplifier is guaranteed. the thesis uses the miller compensate technology with a adjusting zero resistance to compensate the operational amplifier
本論文對國內外的模擬低電壓低功耗技術做了廣泛的調查研究，分析了這些技術的工作原理和優缺點，在吸收這些技術成果基礎上設計了一個1 . 5v低功耗軌至軌cmos運算放大器。在設計輸入級時，為了使輸入共模電壓范圍達到軌至軌，不是採用傳統的差動輸入結構，而是採用了nmos管和pmos管並聯的互補差動輸入對結構，並採用成比例的電流鏡技術實現了輸入級跨導的恆定;在中間增益級設計中，電流鏡負載並不是採用傳統的標準共源共柵結構，而是採用了適合在低壓工作的低壓寬擺幅共源共柵結構;在輸出級設計時，為了提高效率，採用了推挽共源級放大器作為輸出級，輸出電壓擺幅基本上達到了軌至軌;本論文改變傳統基準源基於運放的設計，採用了帶電流鏡負載的差分放大器設計了一個基準電流源，給運放提供穩定的偏置電流和偏置電壓，保證了運放的穩定性;並採用了帶調零電阻的密勒補償技術對運放進行頻率補償。 -
The stability of feedback of amplifier circuit is often analyzed with bode in " simulation electron and technology " in the advanced institutes
摘要目前高等院校在模擬電子技術課程中對于負反饋放大電路穩定性進行分析時，一般採用波特圖的分析方法。 -
To compare with transistor ( complete solid - state ) high - frequency linear power amplifier, there are some disadvantages : bad stability and reliability, low efficiency, high cost for operating, huge cabinet, heavy maintenance work load, low security for high - voltage electricity offering, and to ensure the continuance of tv program, the transmitter must be operating with main frame and spare frame
它們與晶體管（全固態）高頻線性功率放大器相比，存在著穩定性及可靠性差、效率低、運行費用高、發射機體積大、日常維護工作量大、高壓供電不安全、必須採用主機和備機的運行方式來確保電視節目不停播等缺點。 -
In view of the problem of signal - to - noise and stability of circuit of photoelectric detection for weak signal, a low - noise amplifier circuit of photoelectric detection is designed, with the functions of filter and phase compensation
摘要針對光電檢測中對微弱信號放大而帶來的信噪比和穩定性問題，設計了一種低噪聲光電信號放大電路，它具有電壓、電流濾波和相位補償功能。 -
The 2 - stage differential transconductance amplifier is used in the design to achieve high gain. in the design of amplifier, a resister and a miller capacitor is used to deal with the stability and frequency compensation
系統中採用差分跨導運算放大器的設計，為了保證其具備高增益與高穩定性，選用二級結構，並且增加了補償電容和電阻。 -
Through the design the dc feed network, input matching network for the ne900175 gaas fet and analysis the stabilization, power gain, bandwidth of the power amplifier we get the power amplifier is stability, the power gain is 11. 967db and the bandwidth is 300mhz. microstrip antenna has a narrow bandwidth, in this design antenna ' s bandwidth is 100mhz. antenna is the not only the load of the power amplifier, but also as the filter connecting to the output of the power amplifier
E類功放的pae相對a類、 b類、 ab類的功率放大器類型而言比較高，在50 ? 70 。分析了e類功放的工作過程后，以ne900175的gaas場效應管作為e類功放電路的開關，進行了外圍電路的設計，包括直流偏置電路、輸入匹配網路的設計，功放的穩定性、帶寬、增益的分析。該功放增益最大達到11 . 4db ，帶寬為320mhz 。 -
First, we analyse the power amplifier in theory in the circuit mode, biasing point linearity, thermal stability, input and output matching circuit
論文首先從理論的方面對放大器的設計進行分析，對放大器的電路模型、偏置點、線性、熱穩定性、輸入輸出匹配進行理論上的分析。 -
Based the research on the laser beam drift feedback control technique, analysing the beam drift and its frequency components, a laser beam directional stability method is studied in the thesis in detail, with its measurement and control circuit system that combines the laser beam intensity modulation and the beam drift feedback control technique. in this method, at first the laser beam intensity is modulated with the acoustooptic modulator, then the lock - in amplifier is applied to detect and demodulate the modulating signal, at last a feedback control signal is generated by the dsp control circuit at last, including : 1
本文在原有的激光光束漂移量反饋控制準直技術的基礎上，對光束漂移量信號的數據和頻譜進行了分析，重點研究了一種集聲光調制光強與光束漂移量反饋控制準直技術於一體的激光光束方向穩定方法及其測控電路系統，該方法通過聲光調制實現光強調制，接著通過鎖相放大電路檢測並解調調制信號，然後通過dsp控制電路進一步對光束的漂移量進行反饋控制。 -
The integrated amplifier guarantees a minimal temperature drift, long term stability, and reproducability of the measured values
集成在傳感器中的放大器保證了最小的溫度漂移，同時具有長期的穩定性，和好的測量重復性。 -
Discuss the design of gain and amplifier circuits " stability, make sure the stability ' s determinant and design methods
在明確功放功率關系基礎上提出其增益設計方法;詳細討論了放大器電路的穩定性，明確了穩定性的判定和設計方法。 -
We decide to use seven - sections coupled - line filter after comparing the various filter circuits, and complete the quantitative analysis and optimization design by ads, hfss etc. ( 2 ) three - stages fet low noise amplifier according to the lna ’ s design theory and guide line, we decide to use ne3210s01 fet and choose the form of three - stages, thus we can achieve high stability, low noise and high gain
通過對各種帶通濾波器電路方案進行比較，確定採用七階平行耦合微帶濾波器，並利用ads ， hfss等工具進行了定量的理論分析和優化設計。 （二）三級聯低噪聲放大器根據微波lna設計原理及指標要求，我們選用ne3210s01系列低噪聲管，並採用三級放大的形式，以期獲得高穩定性，低噪聲，高增益。
分享友人