arc center 中文意思是什麼

arc center 解釋
弧心
  • arc : A. R. C. ＝ American Red Cross 美國紅十字會。n. 1. 弧；弓形，拱（洞）。2. 電弧，弧光。
  • center : n vt vi 〈美國〉＝centre n 1 中心；中心點；圓心；中央；中樞，核心；中心人物；根源，起源。2 〈常C ...
  1. There are many beautiful scenes, like london ' s big ben, france ' s arc de triomphe and the twin towers of the world trade center that were bombed by osama laden

    這里甚麼也不缺，你可以在這里看到英國的大笨鐘、法國的凱旋門和過去的紐約世貿中心姊妹樓。
  2. The relation of radius of curvature and error as well as formulas of increasing parameters on condition of constant error are diverted. the equation of the line on the center of approximate circular arc is obtained ， and it can avoids the trouble that numerical solution owns possibility of no convergence and simplifies node calculation of non - circular curve

    導出了曲率半徑與逼近誤差之間的關系和等誤差條件下的參數遞推公式，建立了通過逼近圓弧圓心的直線方程和圓心坐標計算公式.按這種方法用圓弧逼近平面參數曲線，不需要求解非線性方程組，避免了計算可能不收斂的麻煩，簡化了非圓曲線的節點計算過程
  3. Arc augmentation research center

    擴大研究中心
  4. With the new - simple method, the equation of circle - arc - enveloping curve are deduced. also the relationship between the arc radius, the radius of center distribution and the distance of centers is given to avoid undercutting

    文中採用新方法推導出了圓弧包絡線轉子型線方程，還給出了避免出現根切現象的圓弧半徑、圓弧圓心分佈圓半徑以及中心距三者之間的關系。
  5. The axial magnetic field distribution on center surface of contact gap and contact piece are calculated when the current is at peak. it can be found that the intensity of axial magnetic field and radial magnetic field uniformity are strengthened after the iron core is put into, this helps to improve the stability of the vacuum arc

    計算了電流峰值時觸頭間隙中心平面和觸頭片上的縱向磁場分佈，可以看出加入鐵芯后縱向磁場強度和徑向磁場均勻性增強，這有利於提高真空電弧的穩定性。
  6. Center hole allows long punch use. with its radius dresser arm, it is able to dress wheels to different straight, arc profiles

    本產品附有曲臂，具有修整砂輪的功能，可用於修整由直線和圓弧組成的各種截面形狀的砂輪。
  7. This short - arc coupled with the low pendulum effect achieved by pivoting the disc through a point near its center of gravity assures rapid closure

    繞軸旋轉的閥瓣的重力中心距軸心較短，因此這種短弧的鐘擺效應也比較小，從而確保能夠迅速關閉。
  8. Secondly, combining practical survey method and time - resistance mathematic model, the author obtained average time distance from every time - cell to fictitious time center, isotime curve figure ( by arc view 3d analyze ) and temporal shape

    然後利用實際測量法和理論公式法計算出深圳特區各時間單元的平均時間距離，並用arcview中的3d分析模塊自動生成等時線圖。
  9. One pencil is the simulative milling cutter. parameters setting, milling cutter radius compensation, graphics drawing of the work - piece machined, realizing local control, etc. are the tasks of pc, while line & arc interpolation, motion segment acceleration & deceleration control, position protection at a high precision rate and so on are the duty of dsp motion controller. in the end, the system can draw the cutter center track of the work piece ' s program track accurately

    上位pc機主要完成相關參數設定、刀具半徑補償相關運算及繪制被加工工件的輪廓（程編軌跡） 、實現本地控制等內容；下位機dsp控制器則充分利用美國ti公司的tms320c31浮點dsp的高速度、高精度完成運動控制中的實時直線和圓弧數值插補、運動段加減速控制、運動軸行程限位保護等內容。
  10. In the wafer notch detecting part, edge flexion method is adopted to find the notch range, then calculating the notch center by means of arc fitting

    缺口檢測先採用邊緣變化率演算法查找缺口范圍，再通過圓弧擬合的方法求出缺口中心位置。
  11. Arc center probe

    圓心自動定位
  12. The results show that columnar center zone was observed in the tri - mixed gas arc shape

    結果表明，三元混合氣體的電弧形態中可觀察到柱狀中心區。
分享友人
分享到 Line

分享到臉書