arc current frequency 中文意思是什麼
arc current frequency
解釋
弧流頻率-
Multiple functions available ： start / crater arc current, increase / decrease time, base / crest value current, pulse frequency, pulse rate, post flow time, hf welding
功能豐富：起始/收弧電流、上升/下降時間、基值電流、峰直電流、脈沖頻率、占空比、滯后關氣時間分別可調，高頻引弧。 -
Multiple funcyions available : start / crater arc current, increase / decrease time, base, crest value current, pulse frequency, pulse rate, post flow time, hf / friction welding, water / gas cooling
功能豐富：起始/收弧電流、上升/下降時間、基值電流、峰值電流、脈沖頻率、占空比、滯后關氣時間分別可調，高頻/接觸引弧、水冷/氣冷可供選用。 -
Transitional feature of the arc and metal droplet in the welding process with steam shielded arc is investigated by means of analysing the waveforms of welding voltage and current under different welding regimes and it is found that there are two types of arc process behavor ? " arc starting - arc blowing out - short - circuiting " and " arc - starting - short - circuiting ". under the condition of constant diameter of welding wire and its feeding speed, the arc process behavor can be changed by adjusting the inductance of welding circuit as well as the voltage of power supply. if arc process behaves as alternative process of " arc starting - arc blowing out - short - circuiting " with minimum time duration of arc blowing out and maximum frequency of short - circuit transition, the welding process will be stable with less spatter and smooth weld bead
通過分析不同焊接規范下的焊接電壓和電流的波形.研究了水蒸氣保護下電弧及熔滴過渡的特點，發現其電弧過程行為有「燃弧?熄弧?短路」和「燃弧?短路」兩種形式.在焊絲直徑和送絲速度一定的情況下，通過調節焊接迴路中的電感量和電源電壓，可以改變電弧的過程行為形式.若電弧過程呈「燃弧?熄弧?短路」交替進行，並且熄弧時間最短時，短路過渡頻率最高，在這種情況下，飛濺小，焊道成型好，焊接過程穩定 -
A novel current control mode pulse width modulation switched high frequency resonant arc igniting device is developed based on uc3842 and the principle is analyzed
摘要採用uc3842設計了電流控制型脈寬調制開關式高頻振蕩引弧器，並對其工作原理進行了分析。 -
The variable polarity power supply circuit uses two stages full - bridge inverter, the former inverter is regarded as a constant - current source with fast dynamic response, and supplys energy for the second one, and the latter one is to produce variable polarity current excellently, and low - frequency pulse current by variable polarity power supply is used to reduce input energy and control the shape of weld bead while welding. a series of high - frequency pulse current is superposed on direct - current - electrode - negative ( dcen ) current through the high - frequency pulse power supply, which is used to compress the arc and improve process of crystallization
其中變極性電源採用二次全橋逆變結構，一次逆變提供快速的響應速率並給二次逆變提供能量，二次逆變提供良好的變極性性能，使輸出能量最優化，並用其低頻電流特性減小電弧線能量，控制焊縫成形;高頻脈沖電源提供的高頻電流疊加在反極性電流dcen上，利用電流的高頻特性壓縮電弧，改善焊縫金屬結晶過程。 -
Design high frequency to increase voitage and pulse heat to strike arc, so with fine ability to start arc. so with fine ability to start arc. welding current is sufficient
採用高頻增壓引弧及脈沖熱引弧設計，起弧性能極佳，焊流電流充足，卓越的性能價格比。 -
Through studying the principle of dimmer and switch power supply, it was found that in some frequency points, by analyzing the phase of electric voltage and current it can tell if arc faults occur
研究調光燈及開關電源的工作原理可以發現，通過分析迴路中電壓電流在某些頻率點的相位信息，可以有效判別是否發生了故障電弧。 -
In recent years, current rectifiers, frequency converters, arc furnaces and other power electronic devices etc have been increasingly used in power network. with nonlinear, impactive, unbalanced characteristics, they generate lots of harmonics and cause distortion in power network current or voltage
近年來，配電網中整流器、變頻裝置、電弧爐以及其它電力電子設備等的應用不斷增加，由於這些負荷具有非線性、沖擊性和不平衡的用電特性，引起供電網中的電流（電壓）畸變，產生大量諧波。 -
As technique of power electronics develops, the load with nonlinear, impactive, unbalanced characteristics such as current rectifiers, frequency converters, arc furnaces have been increasingly used in power network in recent years. they generate lots of harmonics and cause distortion in power electrical network current ( voltage )
隨著電力電子技術的發展，近年來電網中象整流器、變頻器、電弧爐這樣具有非線性、沖擊性和不平衡用電特性的負荷不斷增加，引起供電網中的電流（電壓）畸變，產生大量諧波。
分享友人