arc feeding 中文意思是什麼
arc feeding
解釋
電弧熱補縮-
Backing weld procedure technique of all - position narrow gap and thick - walled pipe welding is developed about all - position single - pass welding section analysis, wire feeding behavior, weld arc length, welding current analysis, procedure and joint test. the achievement has general guide meaning to producing and testing all - position welder
從單焊道全位置區段、送絲行為、焊接弧長（電壓） 、電流行為分析、工藝試驗和接頭檢驗等幾方面介紹管道全位置打底焊工藝特點，其研究成果對全位置焊接機的製造和調試具有普遍指導意義。 -
Abstract : backing weld procedure technique of all - position narrow gap and thick - walled pipe welding is developed about all - position single - pass welding section analysis, wire feeding behavior, weld arc length, welding current analysis, procedure and joint test. the achievement has general guide meaning to producing and testing all - position welder
文摘:從單焊道全位置區段、送絲行為、焊接弧長（電壓） 、電流行為分析、工藝試驗和接頭檢驗等幾方面介紹管道全位置打底焊工藝特點，其研究成果對全位置焊接機的製造和調試具有普遍指導意義。 -
Besides all these, an automatic wire - feeding circuit and its control system are designed for the welding machine is semi - automatic arc welder
此外，由於焊機為半自動焊機，論文中設計了焊絲的自動送進系統及其調速控制系統。 -
Transitional feature of the arc and metal droplet in the welding process with steam shielded arc is investigated by means of analysing the waveforms of welding voltage and current under different welding regimes and it is found that there are two types of arc process behavor ? " arc starting - arc blowing out - short - circuiting " and " arc - starting - short - circuiting ". under the condition of constant diameter of welding wire and its feeding speed, the arc process behavor can be changed by adjusting the inductance of welding circuit as well as the voltage of power supply. if arc process behaves as alternative process of " arc starting - arc blowing out - short - circuiting " with minimum time duration of arc blowing out and maximum frequency of short - circuit transition, the welding process will be stable with less spatter and smooth weld bead
通過分析不同焊接規范下的焊接電壓和電流的波形.研究了水蒸氣保護下電弧及熔滴過渡的特點，發現其電弧過程行為有「燃弧?熄弧?短路」和「燃弧?短路」兩種形式.在焊絲直徑和送絲速度一定的情況下，通過調節焊接迴路中的電感量和電源電壓，可以改變電弧的過程行為形式.若電弧過程呈「燃弧?熄弧?短路」交替進行，並且熄弧時間最短時，短路過渡頻率最高，在這種情況下，飛濺小，焊道成型好，焊接過程穩定 -
A control method is presented where least square arc approximation and timed interpolation are employed. using it, the number of segments of fitted curves is made minimum while the accuracy is guaranteed, so that data transmission between cad and cnc systems is decreased and setted feeding rate can be realized. this method has already success fully been used for flame cutting and controlling saddle - backed curve for pipe connection when feeding rate is required to be higher
提出了一種採用最小二乘法圓弧逼近及定時插補控制方法，在保證精度的前提下，可使擬合圓弧段數最少，從而減少cad系統與cnc系統的數據傳送，可實現給定進給速度.該方法已成功地應用於要求較高進給速度的接管馬鞍型曲線火焰切割擬合控制 -
The " production line " is composed of auto - cutting feeding, autoasembly, auto - submerged - arc welding and frange - corrcting, etc
該"生產線"由自動切割下料，自動組立拼裝、自動埋弧焊接及翼緣矯正等部分組成。
分享友人