axial cylinder 中文意思是什麼

axial cylinder 解釋
軸向缸
  • axial : adj. 1. 軸的。2. 成軸的。3. 軸周圍的，軸向的。adv. -ly 在軸的方向，與軸平行地。
  • cylinder : n 1 圓筒；機筒；烘筒；量筒；（印刷機等的）滾筒。2 【數學】柱（面），柱體。3 【機械工程】汽缸；【...
  1. Xm ) trundle needle, trundleing the post thrust bearing trundles the needle through the roll part of the body, cylinder roller and thrust maintain shelf and the thrust bed down the livestock to make up, trundleing needle and the cylinder roller is subjected to the shelf maintaining that the thrust maintains and guides. moreover thrust bed down the livestock against the difference, shaft, the pedestal encircles and employs in company, fix module shaft shoulder end face and the shell opening back plane dimensional tolerance, geometry accuracy, rigidity, axial is moved up and down, coarse degree ought to accord with the internation ， national standard stipulation demand

    滾針，滾柱推力軸承由滾動體滾針，圓柱滾子及推力保持架和推力墊圈組成，滾針和圓柱滾子受到推力保持的保持架引導，並與不同的推力墊圈，軸，座圈一起使用，安裝組件的軸肩端面和外殼孔底面的尺寸公差，幾何精度，剛性，軸向跳動，粗糙度應符合國際，國家標準規定的要求。
  2. Dynamic behavior of viscoelastic cylinder in axial flow

    軸向流動中粘彈性圓柱體的動力特性分析
  3. Kinematics of the axial piston pump with swash plate yoke ' s angle were analysed. there was a lot of analysis about relative movement between piston and cylinder block, between piston and swash plate, between slipper and swash plate. at same time, the movement simulation curves were given

    對軸向柱塞泵進行運動學分析，重點是對柱塞與缸體之間，柱塞與斜盤之間以及滑靴與斜盤之間的相對運動進行分析，並且分別給出了模擬曲線； 2
  4. Ma yan ? ying, liu jia ? qi. experimental investigation of oil film of port plate / cylinder block in axial piston pump j. lubrication engineering, 1999, 3 : 3539

    鄭煒， ?有雄，魯寶香.軸向柱塞泵配流副油膜的實驗研究j .潤滑與密封， 1995 ， 5 ： 3739
  5. Zhou shi ? yu, duan zhan ? xu. experimental investigation of gap of port plate / cylinder block in axial piston pump j. chinese hydraulic & pneumatic, 1986, 3 : 1214

    許耀銘.軸向柱塞泵滑靴和配流盤摩擦副的設計與實驗研究j .液壓與氣動， 1977 ， 2 ： 312
  6. According to the principle of curve axial symmetry, authors inferred the theoretical foundation of error - free translation of the working equipment of loader and proved that when the diameter of piston rod on arm oil cylinder was designed properly, the two oil cylinders could be guaranteed to have a synchronous movement which made the bucket maintain translation throughout the working process under the condition of the oil cylinder ' s basic parameter ; also made the equipment structure of the loader greatly simplified and provided the reference for improvement of the present equipment of loader

    根據曲線軸對稱原理，推導出了能使裝載機工作裝置無誤差平移的理論基礎，證明了只要適當地設計動臂油缸活塞桿直徑，就可以在油缸的基本參數上保證機構工作時兩油缸同步運動，使鏟斗在作業過程中保持平移；使裝載機工作裝置結構大為簡化，為進一步改進現有裝載機工作裝置提供參考。
  7. The derivation of the leakage flow rate formula of the special annular clearance between the piston and cylinder under condition of variable viscosity in the axial piston pumps was carried out. at same time, considering the questions of the eccentricity and the variable sealing length of piston friction pair, the modified coefficient of the calculation formula of the flow - rate of the leakage was given

    在變粘度、柱塞偏心以及變密封長度條件下，對軸向柱塞泵中柱塞與缸孔之間的特殊圓環縫隙的泄漏流量公式進行推導，得到了該計算公式的修正系數； 6
  8. The influence of various factors on the generated axial thrust force of the spirally grooved cylinder is studied experimentally. the comparison of the theoretical results and experimental data is made. the results indicate that theoretical results are consistent with experimental data

    第六章，設計建造了實驗測試臺，加工了一矩形螺紋的微型機器人，通過實驗測試和理論分析，對比分析了實驗測量結果和理論計算結果。
  9. Hydraulic fluid power - cylinder rod and piston seals for reciprocating applications of co - axial seals - dimensions and tolerances

    液壓缸活塞和活塞桿動密封裝置用同軸密封件尺寸系列和公差
  10. Calculation for the ultimate axial bearing capacity of large diameter prestressed concrete cylinder pile

    預應力混凝土大直徑管樁軸向極限承載力計算
  11. The basic selection, the cylinder body coiling and so on in making the axial catalyst baskets in ammonia synthetic columns were presented, the causes were analyzed, and the corresponding methods were proposed

    主要介紹了氮合成塔軸向觸媒筐在製作組對過程中出現的基準選擇和筒體卷制等問題，分析了原因，提出了解決的方法。
  12. Hydraulic fluid power - cylinder rod and piston seals for reciprocating applications of co - axial seals - dimensions and tolerances of housings

    液壓缸活塞和活塞桿動密封裝置用同軸密封件安裝溝槽尺寸系列和公差
  13. The rotating cylinder lies on the swinging rack, supported by four wheels and its axial fixation power system to made the cylinder rotate

    轉裝在擺動架上，由四個滾輪支撐並由兩個傳動輪對其進行軸向定位。
分享友人
分享到 Line

分享到臉書