axis based error 中文意思是什麼
axis based error
解釋
軸線誤差-
In two axis system, a circle interpolator is designed, and a new method based on ga - neural networks is proposed to adjust pid parameters online to reduce the tracking error. then, an integrated controller based on rbf neural network ( rbfnn ) is designed to reduce the contouring error of the two axis. experimental results show that the proposed integrated controller significantly improved accuracy in both tracking and contouring
對于雙軸系統設計了一個軌跡為圓的插補器，採用基於遺傳演算法?神經網路的在線pid參數調整演算法，減小了系統的跟蹤誤差，並分析雙軸之間的輪廓誤差，設計出基於rbf神經網路的綜合控制器，經過模擬實驗證明，本文採用的綜合控制器能有效地減小系統的跟蹤誤差和輪廓誤差，提高系統的控制精度。 -
Consider to simplifying the process of calibrating dynamic error parameters of accelerometer and shortening the time of calibrating test, all dynamic error parameters are calibrated at one - time, based on the mathematic model of dynamic error of accelerometer and integrating the model and the testing theory of the three - axis turntable, meanwhile, the angle - vibration table is avoided
摘要為了簡化加速度計動態誤差系數的標定過程，縮短標定試驗時間，在建立加速度計動態誤差數學模型的基礎上，結合三軸轉臺模型及測試原理，一次性標定出加速度計動態誤差系數，同時避免了角振動臺的使用。 -
The mathematic model of the ultra - thin spherical mirror is to be treated as elastic thin shell. then the predigested model, i. e., bended beam, used in qualitative analysis was proposed, and its deflection and stress formulas under the freely supported condition were set up. based on an off - axis aspherical primary mirror, the relationship of aspherical surface error ( rms ) in tangential plane with bended beam ’ s radius r, position s of concentrated load p and geometry length l of arc was analyzed
根據這一設想，本文建立了超薄鏡的數學模型?薄殼，並提出了強制力作用下超薄鏡的簡化模型?曲梁，推導了曲梁在簡支情況下受力變形的撓度公式，並結合一個實例，計算出曲梁變形后與所需非球面的面形殘差（ rms ）在子午方向與曲梁弧長l 、曲梁半徑r及集中力位置s的關系及滿足面形精度的r和s范圍，分析了弧矢方向的rms ，得出了同時滿足子午和弧矢方向面形要求的l 、 r和p 。 -
Axis - misalignment error compensation method based on optical alignment for a multi - sensor assembly
基於光對準的多傳感器軸裝配誤差補償技術 -
To machine the honeycomb sandwich, an interpolation method based on a rotary axis is also studied. with the round vector function and rotary movement group, a model of the error curved surface of the theoretical ellipsoid is set up to describe the actually measured surface
以圓矢量函數和回轉運動群為工具討論了曲面的誤差變換，利用理論橢球面的誤差曲面建立了實測曲面的數學模型，通過求解理論曲面的法線實現了實測曲面的等距計算和陰陽面數據轉換。 -
In this subject, a new method and technique that applied the error separation theory to test of the surface flaw of axis - like parts using eddy current is proposed for the first time. based on this method, a mathematical model of extracting the surface flaw of axis - like parts is established. then " an automation system for the eddy current examination of the surface flaw of axletree " is designed
本課題首次應用誤差分離理論提出了對軸（孔）類工件表面缺陷進行渦流無損檢測的新方法和新技術，建立了基於該方法的提取軸（孔）類工件表面缺陷的數學模型，並設計了「軸承滾子表面缺陷渦流自動化檢測系統」 。 -
Second, based on the theory of error separation, the mathematical model, which is used to extract the surface flaw of axis - like parts, is given briefly. third, the designs of hardware and software in the system are explained respectively. fourth, the models and algorithms for appraising the surface flaw of axis - like parts are established by the methods of pattern recognition and neural net
第一，本文論述了該課題研究的必要性及應用開發的價值：第二，簡要介紹了基於誤差分離理論建立起來的提取軸（孔）類工件表面缺陷的數學模型；第三，對該系統的硬體和軟體設計分別進行說明；第四，運用模式識別和神經網路等方法建立軸承工件表面缺陷評判模型和演算法，並給出了各種評判方法的比較。 -
This project is based on the theory of mbs, analyzes all movement forms of 3 - axis nc machine tools, builds the movement models of all kinds of models, and summarizes the general movement model, which includes two methods ? rom work piece coordinate system to unitary coordinate system and from unitary coordinate system to work piece coordinate system. each method includes the movement models both under ideal condition and under error condition, so the 3 - axis nc machine tools are defined
本課題以多體系統理論為基礎，分析了三坐標數控機床的所有運動形式，建立了各種類型三坐標數控機床的運動模型，並從中概括出通用性的運動模型，其中包括從工件坐標系映射到機床參考坐標系和從機床參考坐標系映射到工件坐標系兩種情況，每種情況又包括理想情況下和存在誤差情況下的運動模型，解決了三坐標數控機床運動誤差補償的通用性問題。 -
Based on 5 - axis nc linkage, aocmt can generate freedom - form surface in normal manner, and grinding accuracy is better than 8 m. 4. according to the error component of various wavelength, feeding step length, convergence ratio and anastomotic status, a new method which determines the dimension of the polishing tool is presented
4 、提出了根據不同成分面形誤差的分佈特徵、進給步距、收斂比和吻合特性要求，確定研拋盤尺寸的新方法；對ccos加工中研拋模運動路徑的規劃進行了深入研究，並給出了相應的工藝流程和技術規范。
分享友人