beam design formula 中文意思是什麼
beam design formula
解釋
梁計算公式-
Considering the special structure of multi - ribbed slab, founding diphase body mechanical model of compound material, strengthening rib beam and rib pillar by equivalent volume ratio of concrete and slice brick, the paper drew elastic compution constant and shear constant. based on the things, the paper simplified isotropy compution model to wall, gave practical design formula of elastic mold and shear mold, provided necessary parameter for practical design formula of elastic rigidity. finally the calculating results agree well with the text results
結合密肋復合墻板的特殊構造，建立墻板的復合材料二相體力學模型，按照混凝土與砌塊體積比不變原則對肋梁肋柱同時加強，得出墻板的彈性計算常數及剪切常數，在此基礎上，進一步將墻板簡化為各向同性的計算模型，給出墻板彈性模量及剪切模量實用計算公式，為密肋復合墻板的實用彈性剛度計算公式提供必要的參數。 -
Based on the experiment results, the damage form of abnormal exterior joint are summarized, characteristics of hysteresis curve are studied, the effect of stirrup ratio and height of column section and beam section on anti - shear property of abnormal joint are discussed, working mechanism of abnormal exterior joint is researched, the conclusion that the anti - crack and bearing capacity of abnormal joint are studied by analyzing the minor core of abnormal exterior joint is proposed, the basic data is provided for the design formula of abnormal joints
根據試驗結果，總結了異型邊節點的破壞形態，研究了節點滯回曲線的特徵，討論了節點核芯配箍率、樑柱截面高度變化對異型邊節點抗剪性能的影響，分析了異型邊節點的受力機理，提出應以「小核芯」為分析單元來研究此類節點抗裂和承載力的建議，為異型節點設計公式的建立提供了基礎數據。 -
Regarding the rc beams subjected to concentrated load or even load and braced by bonding steel, an analysis is made on the relevant factors influencing maximum anchorage shear stress of steel sheet. the analysis is based on elastic theory and makes use of the formula for calculating anchorage shear stress of steel sheet. as indicated by the results, the maximum anchorage shear stress not only realtes to such parameters as height of cross section of rc beam and span but also relates to the thickness of adhesive layer, elastic modulus, thickness of steel sheet, and length of steel sheet. the present method will check maximum an chorage shear stress on the end of shear sheet so as to prevent rc beam from local damage. the present results will offer important reference for our country to further perfect bracing design by bonding steel method
在彈性理論的基礎上，利用鋼板錨固剪應力計算公式，對在集中荷載或均布荷載作用下採用粘鋼加固的混凝土梁，分析鋼板錨固最大剪應力的有關影響因數.結果表明，最大錨固剪應力不但和混凝土梁的截面高度、跨度等參數有關，還和粘膠層厚度、彈性模量、鋼板厚度及鋼板長度有關.採用文中方法可以對鋼板端部最大錨固剪應力進行驗算，防止混凝土梁出現局部受拉破壞.研究結果為進一步完善我國粘鋼法加固設計提供重要的參考資料 -
Since it is difficult for the cable or beam model to consider the large deformation in the pipe crossing section, the fem analysis with shell element has been proposed to investigate the response of pipe. takada ( 2000 ) proposed a simplified design formula to obtaining the maximum strain in steel pipes based on the parametrical study using a beam - shell hybrid fem
現在的抗震規范和有關研究中，還很少有估計大變形時管子內的應力應變的方法，雖然2000年高田至郎等人基於殼有限元模型的參數研究提出了設計用的簡化計算公式，但在他們的分析模型中存在一些問題有待改進。 -
Then calculate the member individually, including the calculation of load - behavior capacity, the calculation of high strong bolt with the method of connection with beam, the design method of stiffening rib, etc. the text educed the above - mentioned formula theoretically. 5. linking with windmill flat engineering example in the third youth flat engineering of yi zhuang development area, beijing, it and steel frame constitute the steel frame ? steel shear wall with slit system respectively are analyzed the whole structure by ansys and satwe
既利用剛度等效的原則，把其轉換為工程計算軟體可以計算的支撐體系，然後對構件進行單獨計算，包括承載力的計算、和梁接合方法? ?高強螺栓的計算、加強肋的設計方法等內容； 5 、帶縫鋼板剪力墻與鋼框架形成鋼框架? ?帶縫鋼板剪力墻結構體系，結合北京亦莊經濟開發區青年公寓三期工程中的風車公寓工程實例，分別採用ansys和satwe進行了結構整體分析，兩者的計算結果相吻合。 -
Abstract : simplifying the formula in code for concrete structure design ( gbj10 - 89 ), we obtaine the appoximate formula of crack width, that is used to the beam of rectangular section in design
文摘:對《混凝土結構設計規范》 （ gbj10 - 89 ）中的裂縫寬度計算公式進行化簡，得出矩形截面梁裂縫寬度實用計算公式，供工程設計時使用。 -
Summarizing the above - mentioned research results, the design method of two kinds of connection ways of steel braces is proposed, which include the calculation formula of the steel braces, the head studs, steel angels at four corners of beam and column and embedded steel framework
本文在上述試驗的基礎上，提出了兩種支撐加固連接方式的計算公式，包括支撐桿件、栓釘、外包鋼連接和鋼內框連接等。 -
Local buckling capacity of steel composite beam subjected to combined bending, shear and patch loading is one of key problem in steel structures design. the computational formula for local stability of web was based on the assumption of infinite - elastic perfect plates in the steel structures design code ( gbj17 - 88 ). but in the revised code ( gb50017 - 2003 ), this formula was made big change with reference to british code ( bs5950, partl ) and australian code ( as4100 ), the related research result of our country was included as well. in the modified formula, influence of early geometric imperfection and elastic - plastic buckling stage were considered, which is compatible with both actual circumstance of engineering and the strength formula of beams under bending stresses ( considering partial plasticity of the section ). in this paper, the preceding problem is deeply analyzed and studied, considering the effects of various geometric parameters and stress combinations on buckling critical stress of web, the revised local buckling correlative formula for transverse and longituded stiffened web panels under combined stresses is analyzed and verified by finite element method
組合鋼梁腹板在彎、剪及局壓復合應力作用下的局部屈曲承載能力是鋼結構設計中需考慮的問題，新的《鋼結構設計規范》 （ gb50017 ? 2003 ）對此部分內容作了較大改動，原規范中關于腹板局部穩定的計算公式是基於無限彈性的完善板假定；新的規范則參考了英國規范（ bs5950 part1 ）及澳大利亞規范（ as4100 ）並結合我國相關研究成果，考慮了屈曲進入彈塑性階段以及初始幾何缺陷的影響。這不僅與工程實際情況相符，而且也與鋼梁在彎曲應力作用下允許截面部分進入塑性的計算公式相協調。 -
The contents include as follows : the influencing factors of the displacement ductility factor of the unbonded partially prestressed concrete frame structures, such as stirrup reinforcement characteristic value, nominal shear span ratio, axial compression ratio, the appearing order of plastic hinges and partial prestressing ralio ( ppr ) are discussed. the formula of displacement ductility factor of the unbonded partially prestressed concrete frame structures is suggested by regression analysis. with regard to the aseismic design and the request of ductility and energy dissipation, the restriction of the flat - beam / column sectional size and aseismic reinforced design are discussed
本文主要包括以下內容：討論了配箍特徵值、名義剪跨比、軸壓比、塑性鉸出現順序、預應力度等因素對無粘結部分預應力混凝土框架位移延性系數的影響，回歸了考慮影響因素的位移延性系數計算公式；對無粘結部分預應力混凝土扁梁框架結構，闡述了抗震設計對扁梁、柱截面尺寸的要求與限制；對滿足延性和耗能要求的無粘結部分預應力混凝土扁梁控制截面抗震配筋進行了探討；通過對無粘結部分預應力混凝土扁梁梁端的受力分析，改進了以往扁梁梁端扭矩設計值計算公式。 -
Several suggestions for amending the defects of pk - pm software were also put forward. moreover, the formula and measured target were proposed through analyzing the change of reinforced concrete eccentric beam - column connections strength. for the design of shear wall beam question, suggestions were proposed ; the suggestions was also verified and explained by a practical construction design
主要內容包括：敘述了結構概念設計在框?剪結構中的具體應用，並給出了算例和相應的公式；對工程設計軟體pk - pm存在的缺陷，提出了改進及建議；對框架樑柱偏心節點強度的變化進行了分析，給出了計算公式及量化指標；對困擾設計人員的剪力墻連梁設計問題給出了設計建議。
分享友人