bearing stud 中文意思是什麼
bearing stud
解釋
支承螺柱-
Concerning the tests, analyses, design and calculation of performances for light gauge steel framing, this paper focuses on following items : ( 1 ) the calculation of light gauge steel framed compound bearing walls ( lgsfcbw ) in compression and bending. based on north american specification and commentary for the design of cold - formed steel structural members, which was published by the american iron and steel institute, the detailed design requirements of wall stud assemblies are given considering the structural contribution of the attached sheathings and shear diaphragm is discussed briefly. then the calculational theoretic and method for sheathing braced wall stud assemblies complying with national code is brought up in compression and bending
本文圍繞輕鋼龍骨體系結構性能的試驗、分析、設計和計算，主要進行了以下四方面的研究工作： （ 1 ）輕鋼龍骨復合承載墻體的受壓、受彎計算：以美國鋼鐵協會發行的北美冷成型鋼構件設計規范及其規范說明為依據，重點考慮罩面材料對墻龍骨設計的影響，給出了目前對承重墻龍骨設計的具體要求，並對剪力蒙皮進行了簡要討論；然後提出了符合我國規范術語的剪力蒙皮作用的輕鋼龍骨復合承載墻體（即罩面支撐墻龍骨）受壓、受彎的計算理論和方法；最後對提出的計算進行簡化，使之完全與我國規范相符。 -
The paper made up a flexural experiment with six pieces of composite slab. during the every step of load exerted, the paper recorded the strain of cold - form steel deck and concrete, deflection, crack, slide, ultimate bearing capacity. by changing the thickness of cold - form deck, thickness and strength of concrete, amount of steel stud and other parameters, the paper discussed the behavior of loaded composite - slab
本文進行6塊組合板的抗彎性能試驗，測試各級荷載下壓型鋼板及砼應變、組合板撓度、裂縫、板端滑移、組合板抗彎極限承載力；通過壓型鋼板厚度、砼板厚度、砼強度等級、栓釘數量等幾個參數的變化，探討組合板在荷載作用下的內力、變形情況。 -
( 2 ) 3d - fem analysis for the load - bearing capacity of the stud connector as the prevailing method to determine the shear rigidity and the limit load - bearing capacity of the shear connector is the push test, which is time consuming and laborious, in this thesis the push tesi specimen of the stud connector is simulated through the non - linear analysis module of the msc / nastran and the numerical analysis results are in good coherence with that of the practicality lev ; as a result, the shear rigidity and the limit load - bearing capacity of the stud connector can be determined by the finite element method and only a few practicality verification tests
（ 2 ）栓釘型剪力鍵承載力的3d - fem分析針對當前剪力鍵一般通過費時費力的推頂試驗來確定抗剪剛度和極限承載力的狀況，本文利用msc nastran非線性模塊實現了對栓釘剪力鍵推頂試樣的數值模擬分析，數值計算結果與試驗結果能夠很好吻合。這使得通過有限元方法的模擬和少量實物試驗的驗證，就能確定栓釘剪力鍵的剪切剛度和極限承載力，可以大大節省時間和經費。 -
Furthermore, the temperature fields of the radial - thrust floating ring hybrid bearing which includes the lubricant inertia item is stud ied for the first time, the reynolds and energy equations are derived, the relationship between viscosity and temperature as well as the boundary condition of pressure and temperature are developed
此外，本文還首次對考慮慣性項下該動靜壓軸承的溫度場進行了理論研究，建立了數學模型，導出了該浮環動靜壓軸承徑向部分、推力部分的能量方程、雷諾方程以及粘溫關系、壓力、溫度邊界條件等。
分享友人