bed material size 中文意思是什麼
bed material size
解釋
底沙粒度-
Suspended and bed load transport were simulated with a non - equilibrium method. the source treatments in sediment transport equations, suspended load carrying capacity of the non - uniform material and exchange of size - distribution of the bed material are presented. 5
二維懸沙和底沙運移採用不平衡輸沙模式，分析輸沙方程的源項處理以及非均勻沙分組挾沙能力和床沙級配調整。 -
Using sawdust as raw material, under the condition of 2 % - 4 % opening rate of distributor, the effects of particle size and sawdust bed height on fluidization velocity in cold bubbling fluidized bed were determined
摘要冷態條件下，在鼓泡流化床中採用木屑為原料，分佈板在2 % ~ 4 %不同開孔率的條件下，分別考察了原料粒徑和床層高度對木屑流化速度的影響。 -
In this thesis, first, reasons and factors for the stability of loose rock dams were summarized according to the field surveys and certain expert ' s experiences. then, researches on block stability problems were reviewed, and according to the relationship between grain size and incipient velocity, it is found that the block weight is in direct proportion to 6 - 9 power of incipient velocity, and 50 % increase of the velocity will result in about 40 times change of the block weight. after that, experiments were conducted in a flume, focusing on the relationship between incipient velocity and some main factors including block weight, water depth over the dam, cross - section size, block material and river bed material
本文首先根據散拋石壩損毀情況的現場調查資料，結合有關專家多年的整治經驗，總結出壩體的損毀原因及影響因素；對現有塊體穩定性的研究成果進行回顧和總結，並針對散拋石壩的直接損毀現象，結合山區河流的水流、地形特點，利用塊體粒徑與起動流速的關系，提出塊體穩定重量與起動流速高次方成正比的概念，流速50的增長可能導致塊體穩定重量接近40倍的變化；通過二維變坡水槽試驗，研究了壩體穩定的主要影響因素，包括塊體重量、壩頂水深、斷面尺寸、塊體材料（塊石和卵石兩種） 、護底等，結果表明對于山區河流，試圖僅僅通過增加壩體單個塊體重量或斷面尺寸來提高壩體穩定性效果甚微；最後，根據西部地區的自然、經濟、交通等條件，提出可以採用柔性混凝土鉸鏈體等一類整體性較好的護面層作為散拋石壩的防沖毀措施，以期取得良好的工程效果。 -
The equations for the total carrying capacity and the size distribution of carrying capacity and effective bed material have been presented
進而論述不平衡輸沙時總挾沙能力、挾沙能力級配及有效床沙級配的方程。 -
The conclusions are as follows : ( 1 ) high - pressure water - atomization can be used to produce a pre - alloyed steel powder with high apparent density, high green strength, size - stability after sintering and low hydrogen - loss content ; ( 2 ) the higher smelting temperature and / or water pressure, the finer particle size of steel powders ; ( 3 ) when the atomization angle holds in a reasonable value ' s range the obtained powder will have a better particle size distribution ; ( 4 ) an optimum atomization technological parameters : liquid steel flux, water pressure and water prick angle was obtained ( 5 ) reduction variables ( temperature, holding time, material - bed ' s thickness and reducing gas flux ) have a significant effect on the particle agglomeration and properties of final powder was given ( 6 ) different alloying methods were developed to modify properties of ferrous powder materials and hence to broaden its applications in ferrous powder metallurgy industry
本文系統研究了水霧化預合金鋼粉生產工藝及合金化方法對鐵基粉末冶金材料性能影響，詳細研究了冶煉、霧化、還原工藝參數對預合金鋼粉化學成份和物理性能影響，並得出如下結論： （ 1 ）採用高壓水霧化技術可用於生產高密度、高強度、尺寸穩定性的低氫損含量的水霧化預合金鋼粉。 （ 2 ）冶煉溫度越高，高壓水壓力越大，所得生粉顆粒粒度越細。 （ 3 ）水錐角調整在一個適當角度范圍內可獲得粒度組成較好的生粉。
分享友人