belt adjustment 中文意思是什麼

belt adjustment 解釋
皮帶調整
  • belt : n 1 帶，皮帶；綬帶；線條；帶狀物。2 【機械工程】傳動帶；【天文學】雲狀帶；【軍事】子彈帶；腰皮帶...
  • adjustment : n. 1. 調整；調節（裝置）；校正。2. 調節。3. （賠償損失的）清算。
  1. It is equiped with imported inverter, transmissing belt and air - intake machine ; convenient use, flexible adjustment, stable stepless speed regulating and high abrasing resistance

    本機配用進口變頻，輸送帶，吸風機等部件使用方便，調整靈活，傳動部體無級調速運轉平穩，耐用度高。
  2. The transducer speed adjustment is used for the conveyer belt and the brush wheel, and the motor starts to rotate directly to make the machine run more smoothly and the stain done more uniformly

    輸送帶，毛刷輪採用變頻器調速，馬達直接轉動，使得機器運轉更為順暢，著色更為均勻。
  3. This special wrench can be used for loosening the a c idler pulley tension lock - nut for a c belt adjustment or replacement

    用途：適合用在比較窄小空間位置，拆及收緊螺絲，請看參考圖片。
  4. This machine is used for straight - line bevel cutting and bevel grinding and polishing for flat glass, in certain condition, it can be also used in bevel cuttig, bevel grinding and polishing for soft stone panel. the contrilling system adopts plc, it can accomplish automatic grinding cutting after entering processing parameter, convery speed adopts speed adjustment of fre quency conversion, direct drive of wheel head motor, all motions for joining in parameter adjustment completely adopt straight - rolling guide - track with front beam and wheel head lifting lntegrally. the transmission of input and output adopts synchronization tooth belt and photo - electricity switch positioning, and position limitation of two pass is much more reliable

    Sxm371pa型玻璃直線斜邊磨邊機是用於玻璃直線斜邊斜切，斜磨及光拋的專用設備，在一定條件下也可以用於軟石板材的斜切斜磨及拋光。控制系統採用plc控制。輸入加工參數后可自動完成磨削傳送速度採用變頻調速，磨頭電機直接傳動，所有加工參數調整運動副全部採用直線滾動導軌，前梁與磨頭整體升降，輸入輸出傳送採用同步形帶，光電開光定位，雙行程限位更安全可靠。
  5. Set up the v - shaped belt wheel of adjustment in inside, doesn t need extra belt wheel brace

    內建可調整5m三角皮帶輪，不需外加皮帶輪支架
  6. Abstract : the main points of using and maintenance of isuzu nhr vehicle are described in this paper. the concrete contents include following points : checking of the oil level, braking fluid level and the tension of fan belt ; maintenance of the air cleaner and battery ; adjustment of the valve clearance and parking brake

    文摘:闡述了五十鈴nhr貨車的使用與維護要點，即潤滑油油位的檢查;風扇皮帶撓度的檢查;空氣濾清器的維護;氣門間隙的調整;蓄電池的維護;駐車制動的調整及制動液液位的檢查等。
  7. By researching the features of motor torque control and motor speed control in the system, the paper present the methods of tension control and tension compensation of winder and accumulators, the loads balance of speed rollers, and the adjustment to accumulator in order to synchronize the speed of different segment. in order to control the overhang line of steel belt in the heater by pid controller, the method of off - line pid parameters calculation is applied

    論文通過對連續彩塗板交流變頻調速拖動生產線各段張力和速度控制的要求和特點的研究，著重分析解決了開收卷機的張力控制和張力補償方案、活套控制中的張力補償方案、速度輥對間的負荷平衡控制、以及為實現各段速度間速度同步對活套的調節控制等。
  8. It can be used to grind straight line fiat edge, pencil edge, og edge, etc. it adopts synchronized belts two belts, two side holding and synchronized drive to transmit glass, the upper belt can be adjusted vertically according to the glass thickness, two groups of spindles are distributed symmetncally, it can grind two sides at the same time, one of the two groups of spindles is fixed while the other can move horizontally, spindles adjustment can be made in three directions vertical rise and fall, horizontal forward and backward

    可用於磨削直線平邊圓邊og邊等採用同步皮帶雙帶雙側夾持同步驅動傳送玻璃。上帶可根據加工玻璃厚薄作上下調整，兩組唐頭對稱分佈，平行雙邊同時磨削，兩組磨頭其中一組固定。另一組相對可作平行移動，磨頭調整有三種運動垂直升降水平進退以及翻轉。
  9. Belt drives - pulleys - limiting values for adjustment of centres

    帶傳動帶輪中心距調整極限值
分享友人
分享到 Line

分享到臉書