bolt-hole 中文意思是什麼
bolt-hole
解釋
（動物的）避難穴；〈比喻〉安全藏匿所，狡兔三窟。-
The electrical outlet of korea is two aperture, and it is round hole electrical outlet, because this does not carry the electric equipment of 3 bolt, bicephalous flat bolt buys changeover outlet to korea hind ( flat head is changed into round head ) can use
韓國的插座都是兩孔的，而且是圓孔插座，因此不要帶三頭插銷的電器，兩頭扁插銷到韓國后買轉換插頭（扁頭轉換成圓頭）就可以使用。 -
Bolt, hexagonal head, with cotter pin hole, current use
常用帶銷孔六角頭螺釘 -
By inserting the barrel of an arruginated male key in the hole of an unstable female lock, obtaining a purchase on the bow of the key and turning its wards from right to left, withdrawing a bolt from its staple, pulling inward spasmodically an obsolescent unhinged door and revealing an aperture for free egress and free ingress
他將生銹粗澀的男性型鑰匙軸捅進反復無常的女性型鎖孔里，把勁頭使在鑰匙環上，自右至左地轉動鑰匙的凹，將鎖簧送回到鎖環里，痙攣般地把那扇鉸鏈都掉了的舊門朝裏面拽過來，露出可以任意出進的門口。 -
The main popular theoretical method adopted to study end - plate connection is finite element technique under monotonic loading at present. this paper applies nonlinear ( material, geometry and contact ) finite element method to analyze the behaviors of connections under cyclic load at fist time. contact elements are set between end plate and column flange, screw cap and neighborhood plane, bolt bar and hole
對于端板連接的理論分析，目前國內外的研究主要局限在單向加載有限元分析范疇，本文首次採用三維非線性（包括材料、幾何與狀態非線性）有限元對端板連接進行了循環加載分析，端板與柱翼緣間、螺栓頭（帽）與相鄰板件間、螺栓桿與孔壁間都設置了反映邊界狀態的接觸單元。 -
Cylinder head bolt hole
汽缸蓋螺絲孔 -
Pistol drilling, 6 - 8mm glass hole - maker, 6 - 8mm glue grain, level ruler or level pipe mainly for installation of suspended door, 68 expansion bolt, cross and subtraction sign screw driver etc
手槍鉆6至8mm玻璃開孔器6至8mm膠粒水平尺或者平水管主要用在吊趟門安裝6x8膨脹螺絲十字批和一字批 -
There are three lifting holes and one lifting bolt hole on thefront and rear of the machine bed for plugging lifting hooks or bars
床身前後共有三個起重孔和一個起重螺栓孔，用以插入起重工具。 -
Grip clamp with cushion fixed fland using single bolt and lightening hole
帶減輕孔單螺栓側面固定夾緊卡箍 -
Results showed that the ductility of bolt spjice is much better than welds, weaker splice joints develop larger plastic deformation, slipping between faying surfaces, bearing of bolts to hole surfaces and buckling of splicing plates are all ideal energy dissipation mechanism
試驗結果表明：螺栓拼接節點的延性遠好於樑柱焊縫連接；較弱的拼接節點產生較大的塑性變形；接觸面的滑移、螺栓與孔壁的擠壓和翼緣拼接板的屈曲都具有良好的耗能能力。 -
Further more, the fracture possibility is analyzed with fracture mechanics after the stress calculation of local high stress area around the bolt hole in shell flange and the measurement of fracture toughness of gray cast iron. the improving structure of bolts connected head and shell flange is brought forward
此外，在計算獲得缸體法蘭螺栓孔局部高應力區的應力水平后，由斷裂力學分析發生脆性斷裂的可能性，並提出烘缸缸體與缸蓋聯接結構的改進方案。 -
Mount restrictor bar into the restrictor bar groove of upper die, mount adjusting bolt for restrictor bar into the bolt hole in the restrictor bar, then mount lower press block, upper press block
在上模節流棒槽內裝入節流棒，將節流棒調節螺栓裝配進節流棒的螺絲孔中，再裝配上壓塊。 -
Centre of bolt hole
螺孔中心 -
Bolt, hexagonal head, with locking hole, short thread
帶鎖緊孔六角頭短螺紋螺栓 -
Motor used in electric bolt - hole drill for coal mine
煤礦用電動錨桿鉆機電動機 -
Lug body available with iso flange dimensions and metric bolt hole threads. for dead - end service use lug style ( rated 200 psi for this service )
凸耳閥體也可配置iso法蘭尺寸和公制螺栓孔螺紋。用於終端位置可採用凸耳結構（此時額定壓力為200psi ） 。 -
Straighten stamped steel pans particularly around the bolt hole lacations
調整印花鋼盤正好在拴洞周圍的位置。 -
Whether you look to that form of liner plate bolt hole is very special, please see the following picture
還有一點您注意沒有，襯板螺栓孔形狀很特別，您看下邊這幅圖 -
Collection of from plate should be done before use, do not use deformed and can ' t repair form plate, and abandon bolt hole should be made smoothly
4模板使用前應進行選材，不能使用變形翹曲且無法修復的模板，廢棄螺栓孔修補平整。 -
Specification of flange dimension and bolt - hole
法蘭尺寸和螺栓孔規格 -
Lug body available with iso flange dimensions and metric bolt hole threads
凸耳式閥體符合iso法蘭尺寸和公制螺栓孔螺紋。
分享友人