boring method 中文意思是什麼

boring method 解釋
鉆井方法
  • boring : n. 1. 穿孔，鉆孔；鏜削；地質鉆探。2. 〈pl. 〉 鏜屑，鉆屑。adj. 鏜（鉆）孔的。adj. 令人厭煩的，無聊的，無趣的。 boring people 令人討厭的人。
  • method : n 1 方法，方式；順序。2 （思想、言談上的）條理，規律，秩序。3 【生物學】分類法。4 〈M 〉【戲劇】...
  1. Treatment of tibia nonunion with boring method

    鉆孔法治療脛骨骨不連
  2. After having analyzed the common test methods of working stress briefly, the boring - electrical test method is proposed to test the working stress of rc compression member

    對工程中常用工作應力測試方法進行了簡要分析，提出利用鉆孔電測法測試鋼筋混凝土受壓構件的工作應力。
  3. A synthetic evaluation method for quality inspection of cement - soil mixed pile by core boring

    水泥土攪拌樁鉆孔取芯法質量檢測綜合評定方法
  4. The article studies a virtual fine boring system and its cutting data and presents a method to calculate the coefficient of cutting force when boring super - hard steel

    摘要研究了實際的精密鏜削系統及其切削數據，用計算方法探討了用於計算超硬鋼鏜削切削力的系數。
  5. Abstract : it introduces the boring method under different geometric conditions and points to be noted in constructing foundation for piles of tieshan harbor bridge

    文摘:介紹鐵山港跨海大橋樁基礎不同地質情況下的鉆孔方法和注意的問題。
  6. The railway tunnels along canton road and underneath the former marine police headquarters will be constructed by the bored tunnelling method to minimize impacts on the adjacent environment. other than the excavation works that need to be carried out within the works site near the canton road government offices for the new station and introducing the tunnel boring machine, the works that need to be carried out at the street level along canton road will be small in scale so as to minimize the impact on the environment in the neighbourhood

    在廣東道沿路和前水警總部地底的鐵路隧道，會以鉆挖隧道方式建造，除了在廣東道政府合署現址附近的工地內挖開地面以便興建新車站及引進隧道鉆挖機外，需要在廣東道路面進行的工程規模會很少，以便盡量減少對毗鄰環境的影響。
  7. Guide for installation of cable using the guided boring method

    用導向打孔安裝電纜的導則
  8. Evaluation method and program for quality inspection of cement mixed pile in expressway with core boring method

    高速公路水泥土攪拌樁鉆孔取芯法質量檢測評價方法及程序
  9. Method to eliminate the axial movement of boring bar of boring machine

    2206數控活塞異型銷孔鏜床的設計
  10. Standard test method for measurement of dry film thickness of thin film coil - coated systems by destructive means using a boring device

    用鉆孔裝置破壞性測量薄膜盤繞覆層系統的干膜厚度的標準試驗方法
  11. Because there are many function modules in the open - type nc system of the boring and milling machine tool, the work is so large that only a man cannot be completed it. here i just design the framework of the hardware, research the method of some software and develop the emulational interface

    該印製電路板數控鉆銑床的開放式數控系統要研究開發的模塊相當多，工作量也相當大，一個人不可能全部完成，本課題只研究了硬體部分的結構組成和實現方法，軟體部分的實現方法以及控制模擬界面模塊的開發。
分享友人
分享到 Line

分享到臉書