calibration resistance 中文意思是什麼
calibration resistance
解釋
校準電阻- calibration : n. 1. 測定口徑。2. 刻度，標度，劃度數。3. 校準；標準化。
- resistance : n. 1. 抵抗，反抗，抗拒，抵禦；敵對，抵抗力，反抗力，阻力，【生物學】抗病性。2. 【電學】電阻；阻抗；電阻器。
-
Lastly, the minimum permission reliability index is offered by the method of " calibration method " which makes back calculation out of the bending resistance reliability and the compression resistance reliability of the reinforced concrete member in norm
最後，根據「校準法」反演計算現行設計規范中鋼筋混凝土結構抗彎、抗壓可靠度指標以確定在用橋梁結構體系的最低目標可靠度指標。 -
In the paper, through the calibration test of ground load, the relationship between outputs of electrical resistance of strain gauges and the external load applied on the structure has been gotten, and then the load history can directly be deduced from the measured strain history. so the fatigue load can be compiled
本文所建立的應變法實測疲勞載荷，其主要方法是通過進行地面加載標定實驗，確定所設計應變電橋輸出量與結構上作用的外載荷之間的關系，再由實測應變歷程直接得到載荷歷程的方法。 -
Resistance welding - welding current measurement for resistance welding - calibration system
電阻焊.電阻焊的焊接電流測量.校對系統 -
Iso 1 resistance welding - welding current measurement for resistance welding - part 4 : calibration system iso 17657 - 4 : 2005
電阻焊.電阻焊用焊接電流測量.第4部分:校驗系統 -
It is suitable to be used as precise resistance standard for metrology units, research institutes, factories, and especially for meggers calibration
適用於各計量機構、科研與生產部門、用作精密電阻標準，尤其適用於高阻表的檢定。 -
Sb2016 is suitable to be used as power load & standard resistance of every calibration institutions, research institutions, factories and schools, specially for testing and calibration the kinds ofwithstanding voltage tester
適用於各計量與科研機構、工廠與學校作功率負載及電阻標準，特別適用於檢測/校準各種規格的耐壓測試儀。 -
Abstract : the principle of electro - differential - constant temperature detector ( edctd ) is summarized. a calculation method for selecting resistance value in the measurement circuit based on the sensitivity requirement is proposed. theoretical analysis and experimental result for the method are also given. the proposed method can be applied to production and calibration of edctd, providing guideline in determining the resistance parameters
文摘:介紹了電子差定溫式火災探測器的工作原理，提出了根據不同靈敏度要求選取電路中各電阻阻值的方法，並從理論和實驗兩方面加以分析和論證，消除了電阻參數選擇的盲目性，為生產、檢測差定溫式探測器提供了理論依據。 -
In practice, core calibration logging technology is used to establish the logging interpretation model of low resistance reservoir, to quantitatively measure some geological parameters of the reservoir, such as porosity, saturation and permeability, and to combine the core physical experiment, geological composite logging, production test data with multiple well logging data, with the qualitative logging interpretation and the quantitative logging interpretation, so as to deepen the geological understanding on the low resistance reservoir and improve the logging interpretation accuracy
在實踐中，可用巖心刻度測井技術建立低阻儲層測井解釋模型，定量測定儲層孔隙度、飽和度、滲透率等地質參數，並把巖心物理實驗、地質綜合錄井、試油資料與多井測井資料結合起來，把定性測井解釋與定量測井解釋結合起來，以便加深對低阻儲層的地質認識，提高測井解釋精度。 -
Calibration specification for auto - measuring system of thermocouples and resistance thermometers
熱電偶熱電阻自動測量系統校準規范 -
The application of ole technology in the soft ware of auto - calibration system for thermocouples and resistance thermometers
技術在熱電偶熱電阻自動檢定軟體中的應用 -
Realization of internal resistance measurement of lithium battery with auto calibration technology
自動校準技術在鋰電池內阻測試中實現 -
Methods for calibration of bonded electrical resistance strain gauges
粘合電阻應變計的校準方法 -
Calibration of a single range dc insulation resistance tester for one output voltage ( normally not exceeding 5 test points )
按一輸出電壓，校正一臺單量程的直流絕緣阻值測試表（通常不會超過五個測試點） 。
分享友人