cantilever design 中文意思是什麼

cantilever design 解釋
懸臂結構設計
  • cantilever : n. 1. (橋梁的)懸臂,肱梁;支架。2. 電纜吊線夾板;紙條盤。
  • design : vt 1 計劃,企圖,立意要…。2 指定,預定;留給,留著。3 設計,草擬,擬定,籌劃;起草,畫草圖,打(...
  1. Ultrasonic has being attracted much attention gradually in fuel atomization because of some specialities of cavitation and infection on liquid flow. in the course of atomization of pitchy oil, especially, does it show greatly its advantage, but its material atomizational mechanism need research ulteriorly. the primary content of this thesis is about adding cantilever reed to effervescent atomizer so as to combine ultrasonic and effervescent. this thesis has discussed ultrasonic some mechanism, ultrasonic dynamical procreator, effervescent and liquid mucosity infection on atomization, at the some time we make some experiments and discuss atomization rule following some machinery parameter and run parameter so as to find some rule about ultrasonic atomization and to rich the research of ultrasonic atomization mechanism. all that will be beneficial to the design about ultrasonic atomization atomizer

    超聲波由於其空化機理及對液體的流變性影響等特性,在燃油霧化燃燒中逐步引起人們的重視,尤其在重渣油等高粘度液體的霧化過程中逐步顯示出其優越性,但其具體的霧化機理還需要做進一步的研究在氣泡霧化噴嘴基礎加入懸臂式簧片哨,將超聲波與氣泡霧化相結合是本文討論的主要內容本文從研究超聲波的一些機理入手,討論了超聲動力發生器氣泡霧化以及液體粘度對霧化質量的影響,並通過具體的實驗,根據實驗數據來討論霧化質量隨各種結構參數運行參數的變化規律,以便找到超聲霧化的一些規律,豐富對超聲霧化機理的研究,對超聲霧化噴嘴的設計具有一定的指導意義。
  2. The research fruits in this article can provide the temperature isoline map of crown cantilever section and central longitudinal section of the dam, the stress isoline map of crown cantilever section and upstream and downstream surfaces of the dam, the maximal and minimal stress distribution map in dam abutment along with the height of dam, the maximal and minimal stress table of typical nodes and the maximal and minimal stress table in different elevations, and also provide reference basis for taking relative temperature control measures in the design and construction of rcc arch dam

    本文研究成果可給出壩體的拱冠梁剖面和壩體中心縱剖面的溫度等值線圖、拱冠梁剖面和壩體上下游面應力等值線圖、壩肩最大最小應力沿壩高的分佈曲線、不同高程處典型點的最大最小應力值表以及不同高程處最大最小應力值表等成果,為碾壓混凝土拱壩的設計和施工中採取相應的溫控措施提供了參考依據。
  3. Paper 8 - devoe, don l., and albert p. pisano. " modeling and optimal design of piezoelectric cantilever microactuators. " journal of microelectromechanical systems 6, no. 3 ( september 1997 ) : 266 - 270

    論文9純納米管纖維的賴斯提純制備,與凱夫拉爾纖維、采龍纖維相似的先進纖維制備方法
  4. Then an thorough computer modeling using finite element program with material, geometry and state triple - nonlinear taken into account is carried out on a series of influencing factors, such as comparison with npn - beam splice connection, comparison of varies designed theories, and the varying of fraction coefficient, diameter, grade, pretension and arrangement of bolts, thickness of web and flanges of beam and column, splicing location, axial loading on column, etc. lots of useful conclusions are drawn form computer modelling. finally, design and construction suggestions are given out. this study fills the black in the field of steel beam - to - column connection with cantilever beam high - strength bolted - splicing at both home and abroad

    然後,本文在考慮材料、幾何和狀態三重非線性的基礎上,對該連接形式進行了全面的計算機模擬,主要考慮了帶懸臂梁段全螺栓拼接的樑柱連接節點與無拼接的樑柱連接及翼緣對接焊接腹板拼接的連接節點的對比,各種設計方法之間的對比,以及翼緣拼接和腹板拼接的螺栓間距、直徑和數量,拼接點與梁端之間的距離,梁和柱的翼緣、腹板厚度,柱的軸力,接觸面的摩擦系數,翼緣和腹板拼接板的厚度等因素的影響。
  5. Secondly, the construction techniques of cantilever concreting method of girder are analyzed in details. the construction program of stay rope formwork traveler, including the selection of formwork traveler type and the design of formwork traveler, is introduced

    本文重點分析了主梁的懸灌施工技術,從掛籃方案的比選與定型,到掛籃的設計與使用都做了詳細的介紹,本橋採用牽索式掛籃施工方案。
  6. Besides experiments, the present domestic and abroad study on anti - slide pile is mainly analysis by traditional cantilever beam method, foundation coefficient method and elastic mechanic method. on the basis of previous studies, this paper carries out a research on relevant design and calculation theory about anti - slide piles, comprising the interaction between anti - slide piles and rock and soil of side slopes, the soil arching model of anti - slide piles and the internal stress calculation method of prestressed anchor cables

    目前國內外對抗滑樁的研究,除試驗研究外,主要採用傳統的懸臂梁法、地基系數法及彈性力學方法來進行分析。本文在前人的研究基礎上,通過對抗滑樁相關設計計算理論進行研究,包括抗滑樁與邊坡巖土體的相互作用,抗滑樁的土拱效應模型以及抗滑樁預應力錨索的內力計算方法進行分析。
  7. Omnimount s new wishbone cantilever mounts are a breakthrough in flat panel mount design, combining strength, easy installation, and striking product design that is unparalleled in the industry

    懸臂支架omnimount的最新懸臂支架是平面顯示屏支架設計的突破性進展. omnimount結合了行業無雙的容易安裝及惹人注目的產業品設計
  8. 2. a new design and construction method different from the traditional way was used in jinma bridge. when cantilever the main girder of the cable - stayed structure, the longitudinal pre - stressed reinforcements are not tensioned at once

    2 、金馬大橋在斜拉橋設計和施工中採用一種與傳統斜拉橋設計和施工不同的新方法,即懸臂澆築斜拉橋主梁時採用無縱向預應力筋的做法。
  9. Abstract : the paper introduces advantages of cantilever assembly of long - span pc continuous beam. exploration is made on line control, shear key design, matching face treatment and grouting quality requirements, etc

    文摘:結合工程實際介紹大跨度預應力混凝土連續梁懸拼施工的優點,對線形控制、剪力腱的設計、匹配面處理、壓漿質量要求等問題進行了探討。
  10. In a big cantilever overhung structure, unbonded prestressing concrete technology can increase the stiffness of reinforced concrete brace, decreases the de - formation, cut down the column section area, save the cost, solve the difficult problems during the process of design and construction and also enlarge the range of unbonded prestressing concrete technology

    摘要在大懸臂懸挑結構中,利用無粘結預應力施工技術,提高鋼筋砼支撐的剛度,減小變形,減小柱截面面積,節約造價,解決了設計、施工中的難題,擴大了無粘結預應力技術的應用范圍。
  11. Based on the design case of shuangjianghe bridge on the segment from tongdao to jili in g209 national high - way which was being built, the linear cantilever slabs was made to fit transition curve of the route

    摘要以國道g209通道至吉利段改造工程中的雙江河大橋設計實例,研究位於小半徑緩和曲線上預制空心板梁的外懸臂折線逐步逼近緩和曲線線形,與橋上路線線形一致。
  12. By reviewing relevant literatures, it is known that the design model is similar to the cantilever beam structure

    中文摘要植牙術后的骨整合程? ,關繫到手術是否成功。
  13. According to the feature of adamicearth, s engineering geology and calculation of engineering design, the chief problems about traditional calculation method in the earth pressure are studied refering to cantilever - type retaining pile in excavation engineering, and the calculation methods and specific advices are posed

    摘要根據紅粘土工程地質的特點及工程設計計算,針對基坑工程中懸臂支護樁採用傳統計算方法在土壓力計算方面所存在的主要問題進行分析研究,並提出了具體處理意見和計算方法。
  14. Firstly, the relationship of atomic force and distance is studied. the scan type of samples and the working mode of probe is confirmed, then pzt is chosen as actuator for micro scan displacement, and optical deflexion method is used to detect the deflexion value of cantilever. after all these work, the system light path design is finished, and its mathematical model is completed

    首先,分析了原子力探針系統的中原子力?距離的關系,並確定探針系統的探針的工作模式和樣品的掃描模式,從而選擇壓電陶瓷作為掃描微位移驅動器;採用光學偏轉法檢測微懸臂偏轉量,並選用了psd作為傳感元件,並在此基礎上進行了系統光路設計及其數學模型的建立。
  15. Beam - to - column connection with cantilever beam high - strength bolted - splicing in rigid steel frame is widely used in multi - stories or high - rise buildings and industry workshops in the usa and japan, which is also the recommended connection type in our technicall specification for steel structure of tall buildings and code for seismic design of buildings

    帶懸臂梁段高強螺栓拼接的剛性鋼框架樑柱連接在美國和日本的多高層房屋和工業廠房中有著廣泛的應用,也是我國高層鋼結構技術規程和建築抗震設計規范的推薦形式。
  16. According to the design theory of the cable - stayed bridge and to the feature of the cantilever construction the authors propose a construction control method called optimum completion state method ( ocsm ) for rc cable - stayed bridges in the proposed method, the optimum completion state is regarded as the final target of the construction control, and the optimum construction state at each construction stage is taken as the technical route the key of the method is to properly choose or adjust the cable forces the objectives function of optimization is to minimize the elevation error of the girder under the constraint condition that the internal forces ( bending moments ) of the girder are bounded the optimization variables are the cable forces on the basis of the above principles, a optimum model for a construction step is established and cable force adjustments can be found for each construction step in this model, the creep and shrinkage effects of concrete have been considered a bridge example is given which shows that the final state of the bridge is very close to the design aim and that this method is much better than the so - called double - control method the example is a good illustration of the soundness and practical value of the proposed method

    根據現代斜拉橋結構設計理論和懸臂施工方法的特點,提出了以最佳成橋狀態作為施工控制的最終目標,以實施最佳施工階段為技術路線,以索力調整為核心內容的斜拉橋施工控制理論,簡稱為最佳成橋狀態法;以斜拉橋主梁標高誤差最小為目標函數,以主梁內力(彎矩)為約束條件,以索力為優化變量,建立了最佳施工階段的索力調整計算模型;推導了考慮徐變收縮效應的索力調整計算公式;用最佳成橋狀態法對一實橋工程進行了施工控制全過程計算研究,得到的成橋狀態與設計目標相當接近,優于該橋以「雙控」為控制目標的實測結果,有力地證明了本文方法的正確性及其工程實際價值
  17. This thesis presents my study efforts on new type of fiber - optic sensors iber optic bragg grating sensor. prime contents include development and product course of fiber bragg grating ( f5g ), demodulation principles of f5g, design of demodulation system of fiber grating sensors with a cantilever beam, analysis of experiments, and a mechanism based on fiber grating - pair is presented which is used to study the solution of cross - sensitivity of fiber grating sensor measurement

    本論文的研究工作是對新型光纖傳感器?光纖bragg光柵傳感器的應用基礎研究。基本內容包括:光纖光柵的發展和製作工藝、光纖光柵的傳感解調工作原理、基於懸臂梁的實用化的光纖光柵解調系統的設計、原理性實驗結果的分析討論以及提出一種利用光纖光柵對來解決交叉敏感問題的方案。
  18. Design of the biggest cantilever structure garage in our country and trial research of the vertical earthquake force

    我國最大的懸臂結構機庫設計與豎向地震力的試驗研究
  19. Accordingly some available conclusions are obtained in the aspect of analysis and design of the large span and large cantilever structures

    同時本文也在分析與設計大跨度、大懸臂等復雜結構方面得出了有指導價值的成果。
  20. Displacement - based deformation capacity design method of rc cantilever walls

    鋼筋混凝土剪力墻基於位移的變形能力設計方法
分享友人