carbon manganese steel 中文意思是什麼

carbon manganese steel 解釋
碳錳鋼
  • carbon : n. 1. 【化學】碳。2. 【電學】碳精棒[片、粉]；碳精電極。3. （一張）復寫紙。4. 復寫的副本。
  • manganese : n. 【化學】錳。 black manganese氧化錳。 manganese ocher 黑赭石。 manganese spar 【礦物】菱錳礦。 manganese steel 錳鋼。
  • steel : n 1 鋼，鋼鐵。2 鋼製品；刀，劍，打火鐮；（女人胸衣等中的）松緊鋼條[絲]；鋼磨；〈美國〉剃刀，小刀...
  1. Standard specification for pressure vessel plates, low - carbon manganese - molybdenum - columbium alloy steel, for moderate and lower temperature service

    中溫和低溫壓力容器用低碳錳鉬鈳合金鋼板的標準規范
  2. Standard specification for pressure vessel plates, low - carbon age - hardening nickel - copper - chromium - molybdenum - columbium and nickel - copper - manganese - molybdenum - columbium alloy steel

    壓力容器用低碳時效硬化的鎳銅鉻鉬鈮和鎳銅錳鉬鈮合金鋼板的標準規范
  3. And with the increased test time, the superiority of the low carbon high alloy steel was well illuminated. the worn surfaces of the three steels show that the mechanism of the low carbon high alloy steel is impact abrasion, the high manganese steel is impact - corrosion, and the medium carbon alloy steel is the heaviest impact - corrosion

    最後通過hitachi - x - 650掃描電子顯微鏡考察了低碳高合金鋼、高錳鋼和中碳合金鋼試樣的沖擊腐蝕磨損表面形貌，並用olympus光學顯微鏡進行了光學金相分析，對這三種鋼的磨損機理進行一定的探討。
  4. Standard specification for pressure vessel plates, heat - treated, carbon - manganese - silicon steel, for moderate and lower temperature service

    中溫和低溫設備用經熱處理的碳錳硅鋼壓力容器板的標準規范
  5. Standard specification for pressure vessel plates, carbon - manganese - silicon steel, quenched and tempered, for welded layered pressure vessels

    疊層焊接的壓力容器用經淬火及回火的碳錳硅鋼壓力容器板的標準規范
  6. Technical requirements for castings of carbon and carbon - manganese steel

    碳鋼和碳錳鋼鑄件技術條件
  7. Carbon and carbon - manganese steel seamless steel tubes and pipes for ship

    船舶用碳鋼和碳錳鋼無縫鋼管
  8. Standard specification for high - strength carbon - manganese steel of structural quality

    結構級高強度碳錳鋼的標準規范
  9. High manganese carbon steel

    高錳碳鋼
  10. Standard specification for pressure vessel plates, carbon - manganese - silicon steel, for moderate and lower temperature service

    中溫和低溫壓力容器用碳錳硅鋼板的標準規范
  11. Specification for pressure vessel plates, carbon steel, manganese - silicon

    壓力容器用錳硅碳鋼板規范
  12. Steel plate, sheet and strip - carbon and carbon - manganese plate, sheet and strip - specification for hot rolled narrow strip supplied in a range of conditions for heat treatment and general engineering purposes

    鋼板薄板材和帶材.第1部分:錳碳鋼板材薄板材和帶材.第14節:具有一定熱處理狀態普通工程用熱軋窄帶材規范
  13. In this study, the resistance to high impact, corrosion and abrasive wear was determined for low carbon high alloy steel, and for comparison, the high manganese steel and the medium carbon alloy steel are also tested

    腐蝕磨損試驗機的轉速400轉分。在不同的介質（ ph 3 ）和不同的時間內，對低碳高合金鋼、高錳鋼和中碳合金鋼進行了沖擊腐蝕磨損性能的研究。
  14. We discussed the behavior of corrosion - abrasion of the liner of wet - grinding machine in simulated metallurgical conditions. the results show that under the simulated slurry, the corrosion rate and the wear loss of the low carbon high alloy steel is better than the high manganese steel and the medium carbon alloy steel

    實驗表明，在模擬冶金礦山的實際工況條件下，低碳高合金鋼具有優良的綜合性能，壽命最長，是比高錳鋼和中碳合金鋼更適合冶金礦山的嚴酷工況條件的濕式磨機襯板新材質。
  15. Microstructures and mechanical property of low carbon manganese steel with grain boundary allotriomorphic ferrite bainite structure

    貝氏體低碳錳鋼的組織和力學性能
  16. Specification for welding of steel pipelines on land and offshore - carbon and carbon manganese steel pipelines

    陸地和近海鋼管道焊接規范.碳及碳錳鋼管
  17. Transportable gas cylinders - specification for the design and construction of refillable transportable seamless normalised carbon manganese steel gas cylinders up to and including 1 litre

    可運輸氣瓶.容量為1升及以下的可再充裝的可運輸無縫正火碳錳鋼氣瓶的設計和製造規范
  18. Transportable gas cylinders - specification for the design and construction of refillable transportable seamless normalized carbon manganese steel gas cylinders of water capacity up to 0, 5 litre for compressed, liquefied and dissolved gases and up to 1 litre for carbon dioxide

    可運輸儲氣瓶.壓縮液化和溶解氣體用的水容量高達0 . 5升和二氧化碳用的水容量高達升的可再充裝無縫正火碳錳鋼儲氣瓶的設計和製造規范
  19. Standard specification for electric - resistance - welded carbon steel and carbon - manganese steel boiler and superheater tubes

    電阻焊接碳素鋼和碳錳鋼鍋爐和過熱器管的標準規范
  20. Standard specification for steel tubes, carbon and carbon manganese, fusion welded, for boiler, superheater, heat exchanger and condenser applications

    鍋爐加熱器熱交換器和冷凝器裝置的熔焊碳素和碳錳鋼管的標準規范
分享友人
分享到 Line

分享到臉書