cavity profile 中文意思是什麼
cavity profile
解釋
空泡輪廓-
E., the carrier frequency of a gaussian beam deviates from the resonant frequency of a fabry - perot etalon ), variations of the peak intensity, the position of the peak intensity and the dwdm systems, has received considerable attention. in this work, after taking into account the wavelength - depended reflectivity distribution profile of a fiber bragg grating, the oscillation wavelength # _ ( 1 ) of long external cavity fiber bragg grat
與共振情況（即高斯光束的載波頻率與法布里一拍羅濾波器的諧振頻率一致）相比，非共振條件（即高斯光束的載波頻率與法布里一拍羅濾波器的諧振頻率存在偏差）一透射光束的峰值強度、峰值強度所對應的位置、以及光斑的大小隨入射角的變化都發生了顯著的改變。 -
According to the working modes of mr devices, combining the ohm ' s law of magnetic circuit and the design theory of non - steady magnetic circuit, magnetic structures of the automotive damper have been worked out. to emulate the performance of conventional shock absorber, two automotive mr dampers were designed and fabricated at chongqing university. an applied magnetic field increase the yield stress of mr fluids in flow annular passages, which alters the velocity profile of mr fluid in the passages and raise the pressure gradient between low cavity and high one at some given flow rates
根據磁流變阻尼器工作模式，利用磁路中的歐姆定律和動態磁路設計原理，結合汽車懸架的技術要求和結構特點，提出了基於剪切模式和流動模式共同作用（混合工作模式）的汽車磁流變阻尼器設計原理，討論了阻尼器動態磁路設計中的若干技術問題；根據流體力學navier - stokes方程，分別利用newton流體特性和bingham流體特性，推導了基於平板模型和軸對稱模型的流變學方程，得出了阻尼器阻尼力的計算方法。 -
On methods of cavity profile measurement and analysis
空泡外形測量與分析方法研究 -
In chapter 3, we studied the effect of gaussian transverse profile for the driving and laser fields on lasing without population inversion ( lwi ) in a closed v - type system and an open v - type system. moreover, we discussed also the effect of the unsaturated gain coefficient, the cavity - damping rate, the ratio of the atomic injection rates and atomic exit rate on the corresponding systems. in chapter 4, we mainly discussed the effect of doppler broadening on the gain, dispersion and the frequency up - conversion of the open v - type lwi system and compared the differences and the same between the open system and the corresponding closed system
發現： （ 1 ）在考慮doppler展寬的情況下，通過選取合適的實驗室條件（比如合適的原子環境溫度等）可得到合適doppler展寬值，從而使系統獲得最佳增益； （ 2 ）要想實現系統的頻率上轉換，同時又要獲得足夠強的無反轉激光增益，則系統頻率轉換比不能選取的太大； （ 3 ）對于開放系統，比較小的粒子注入速率比與退出速率對產生無反轉激光是有利碩士學位論文摘要的： （ 4 ）由於dopp1oy展寬的存在，當探測場與驅動場的傳播方向相反時，增益在探測場失諧的某一段區域產生振蕩，且振蕩的振幅、頻率失諧范圍的大小與dopper展寬的取值有關。 -
Approximate calculation of super - cavity profile based on slender - body theory
基於細長體理論的超空泡外形估算 -
The pick _ up and analyse for parts data have been made and craftwork decision has been made. profile calculations for turning parts and islands and islets for milling parts problem in mould cavity have been especially made. post process for turning parts and milling parts have been realized
4 、通過對零件數據的提取、分析及工藝決策，深入研究了車削類零件的輪廓計算和銑削類零件型腔中島嶼問題的處理方法，實現了車削、銑削零件的前置處理，形成刀位文件，並生成了相應的零件工藝卡。
分享友人