checking cylinder 中文意思是什麼
checking cylinder
解釋
制動缸-
Cylinder loss and damage can be prevented by careful checking of the condition of the harvested beans and varying the cylinder speed accordingly.
脫粒滾筒造成的損失危害，可以通過仔細檢查收獲豆子的情況和相應地改變脫粒滾筒的速度來防止。 -
According to the high precision and rotation stability requirement of negative scan unit of cylinder photography typesetting machine, the three levels of cylindrical gears transmission separately, the two - stage cylindrical gears - worm drive, and the worm drive was chosen through calculating its velocity ratio, the checking transmission precision, carrying on the movement precision analysis to the sweep unit, and computing overall transmission error
摘要針對圓筒型照相排版機底片掃描裝置要求傳動精度高，轉動平穩的特點，分別選擇三級圓柱齒輪傳動，雙級圓柱齒輪蝸桿傳動，蝸桿傳動3種常見的傳動方式，計算其傳動比，驗算傳動精度，對掃描裝置進行運動精度分析，計算總體傳動誤差。 -
Mounting and grinding of fillet. before mouting the cylinder and doffer should be cleaned thoroughly, trued and balanced accurately ; and the crowns of the back of the fillets should be well rebbed in. the mounting should be done as even as possihie to avoid blistering and followed by careful checking and correction
磨礪的注意事項，包卷前應做好梳理機大小滾筒的平準和平衡工作針根妥為刮平，包卷盡可能平伏，第一次磨礪前將高低不平的針尖和針布接合處須加於充分的整修。 -
This paper deals with synchronous measure technology of the cylinder pressure with the engine cold start by adoping micro - chip aduc812, and it discuss the analysis of breakdown of engine cold start with the mixture of technology of information. through the analysis of the parameters of cylinder pressure of the engine cold start, turning speed and starting electricity, and according to the measure data and witness, a theory is to be inferred, and with the help of breakdown - checking systems, the engine piston groups and the breakdown of starting system can be judged. at last, the. remote measure technology of cylinder pressure ' s parameters
本文採用微處理器晶元aduc812研究發動機冷起動氣缸壓力的同步測試技術，討論了基於信息融合技術的發動機冷起動故障診斷方法。通過對發動機冷起動氣缸壓力、轉速、起動電流等參數的測試，根據測試數據和證據推理理論，藉助故障專家系統，判定發動機氣缸活塞組以及起動系的故障。最後研究了氣缸壓力等參數的遙測技術。 -
Secondly, based on the defects of the uptodate balancing machine which were employed in the motorcycle manufacture plants, this dissertation has presented a new method on the means of checking unbalance mass of the motorcycle single - cylinder engine crank - connecting rod mechanism. it has adopted the hard - bearing balancing machine as the prototype, utilized tow group of resistance sensors placed in vertical direction with one another to pick up the information which stand for the inertial force of the motor engine crank set when it is running
其次，通過對當前國內外曲柄連桿機構動平衡試驗的現狀及其存在問題的分析研究，提出了一種新的測試方法：在工作原理上採用硬支承型測力式動平衡機，在測量方法上應用互成90的兩點測量來矢量合成任意一點旋轉慣性力大小及方向，這也是其不同於以往試驗機的最大之處。 -
The machine which is used for underied - glue lable sticking on cylinder with diameter of 3596mm, can finished setting and colleting bottles at the same time. it s light - optic checking and in - step - with tracing means make sure that the speed of label - sticking can follow the trail of that of bottle - rolling and the labels can be sticked smoothly
該機適用於35 - 96mm的圓柱形的不幹膠標簽的貼標，可一次完成放瓶及收瓶程序，採用光電檢測，同步追蹤，準確保證出標速度與卷瓶速度同步，標簽貼壓平整。 -
This dissertation has presented a new method on the measuring and checking procedures of the dynamic unbalance of the motorcycle single - cylinder engine crank - connecting rod mechanism and made a deep research on its measuring device. what have been done is as follows : firstly, the dissertation has thoroughly discussed the basic theory of rotor unbalance such as its varieties, damages, characters and rules of the movement which is under the excitation of the inertial force and inertial moment induced by the unbalance mass. it also has deeply expounded the dynamic mechanics of the specially formed components - crank shaft, especially in the area of the crank - connecting rod mechanism
本論文針對摩托車單缸發動機曲柄連桿機構為研究對象，對曲柄連桿機構動平衡的測試提出了一種新方法，並對其數字化測試裝置進行了深入研究，完成的主要工作及取得的成果如下：首先，對動平衡理論進行了詳細的探討，論述了不平衡產生的原因、危害，不平衡的種類及轉子在不平衡慣性力激勵下的運動規律，並對曲軸這一結構特殊的剛性轉子的平衡理論進行了闡述，重點研究了曲柄連桿機構這一往復式機械構件的力學特性。
分享友人