circumferential stress 中文意思是什麼

circumferential stress 解釋
環向應力
  • circumferential : adj. 1. 周圍的，四周的。2. 委婉的。
  • stress : n 1 壓力，壓迫，緊迫，緊張。2 【語音】重音；重讀；【詩】揚音；語勢，著重點。3 重要（性），重點，...
  1. The circumferential normal stress is tensile.

    周向正應力是張性的。
  2. Maximum circumferential stress criterion of brittle fracture for v - notch

    型切口脆性斷裂的最大周向應力準則
  3. In order to ascertain stress behavior of steel lined reinforced concrete pipe accurately, according to the fundamental principle of non - linear computation of reinforced concrete elements, the steel lined reinforced concrete penstock on downstream dam surface in a hydropower station is calculated and analyzed, and the distribution of circumferential stress of the steel lined reinforced concrete pipe is obtained, it proves that it is safe and reasonable to use structures of steel lined reinforced concrete penstock in hydroelectric station construction, and can satisfy the requirement of project

    摘要為了能夠準確地把握鋼襯鋼筋混凝土管的受力性能，根據鋼筋混凝土單元非線性計算的基本原理，對某水電站鋼襯鋼筋混凝土壩後背管進行了計算分析，得出了鋼襯鋼筋混凝土管環向應力的分佈情況，分佈情況說明了此水電站採用鋼襯鋼筋混凝土壩後背管的結構形式是安全合理的，可以滿足工程要求。
  4. Maximum circumferential stress criterion of brittle fracture at the interface edge of bonded materials

    結合材料界面端脆性斷裂的最大周向應力準則
  5. It is indicated that the maximum circumferential stress criterion coincides with the experimental results

    實驗表明，本文提出的最大周向應力脆性斷裂準則與實驗結果基本吻合。
  6. Practice for estimating the approximate residual circumferential stress in straight thin - walled tubing

    估算直薄壁管中近似剩餘周邊應力慣例
  7. Standard practice for estimating the approximate residual circumferential stress in straight thin - walled tubing

    估算直薄壁管的大致殘余圓周應力的標準實施規程
  8. Based on the theory of fracture mechanics, the relation between the critical stress intensity factors for v - notch kc and the plane strain crack toughness k10c and the brittle fracture criterion of the maximum circumferential stress for single and double stress singularity with the v - notch problems are proposed. experiments were carried out using two kinds of v - notched specimens made out of plexiglas to verify this brittle fracture criterion

    本文基於斷裂力學原理，推導出了型切口的臨界應力強度因子k _ c與材料的平面應變斷裂韌度k _ （ 10c ）之間的關系，給出了平面單奇異性和雙奇異性型切口問題的最大周向應力脆性斷裂準則，並用有機玻璃板材加工了兩種型切口試樣，進行了實驗驗證。
  9. The theoretical critical pressure of the local stability will be improved further, respectively considering the non - uniformity of circumferential stress distribution over the ring - stiffened cylindrical shell and the torsion of the frame

    分別考慮周向應力不均勻分佈和肋骨扭轉對殼板穩定性理論臨界壓力的影響。
  10. Systematic study is done for the strain energy density factor criterion, distortional strain energy density factor criterion, dilatational strain energy density factor criterion, circumferential tensile stress criterion, energy release rate criterion and twin shear stress criterion

    對應變能密度因子準則、形狀改變能密度因子準則、體積改變能密度因子準則、能量釋放率準則以及最大周向拉應力準則和雙剪應力準則進行了系統地研究。
  11. Based on the numerical simulation for the large - diameter cylinder pile ' s 3d - circumferential flow under wave - flow co - function b using fvm, this paper analyzes the complicated 3d - torrent near the large - diameter cylinder pile, and gives the 3d - flow distribution, the stress distribution on the surface of cylinder pile and in the bed near the cylinder pile, furthermore, analyzes local scour of wave flow in the bed near the cylinder pile

    摘要通過應用有限體積法對在波流共同作用下大直徑圓柱繞流現象進行三維數值模擬，對圓柱體局部復雜流動進行了三維湍流計算分析，給出了三維流場、圓柱體表面及其所在局部底床床面應力分佈，並在此基礎上對圓柱體所在底床的局部沖刷進行了初步分析。
  12. At first, ploygon aggregate structure of concrete is randomly generated in two - dimensional plane with monte carlo method on the meso - level. then, the growth process of a crack of concrete 3 - point bending beam specimen is analyzed by fem, according to the criterion of maximum circumferential tensile stress. and the path of crack to spread in mortar, aggregate and interfaces of them is gained by the ultimate fracture criteria in construction standard that the width of crack should not be more than 0. 2mm

    首先，在細觀層次上，根據蒙特卡羅隨機抽樣原理，在二維平面上建立了混凝土多邊形隨機骨料結構模型，然後採用有限元計算方法，根據最大周向正應力準則，對三點彎曲梁構件進行了開裂過程的模擬，並以建築規范中構件裂縫小於0 . 2mm的要求為最終破壞標準，得出了裂紋在基質、骨料及界面的擴展路徑。
  13. ( 2 ) the numerical result and the critical value ' s effect imposed by circumferential initial stress numerical character on cylindrical thin shell beard the press at axis

    （ 2 ）給出了周向初應力數值特徵對軸向壓力圓柱薄殼臨界值的影響，給出數值結果。
  14. In chapter five, four special problem about initial stress ' s effect to shell ' s mechanics behavior are discussed, including : ( 1 ) the numerical result and the effect imposed by circumferential initial stress numerical character on cylindrical thin shell ' s inherent frequency are given

    第五章討論初應力數值特徵對圓柱殼力學行為影響的四個具體問題，包括： （ 1 ）給出了周向初應力數值特徵對圓柱薄殼固有頻率的影響，給出數值結果。
  15. Through extending the wear plate at the saddle and using the flexible saddle, the circumferential peak stress at the joint of the shell and the saddle can be decreased efficiently

    本文介紹通過鞍座上墊板的伸出和採用柔性鞍座，即能有效地降低鞍座邊角處的環向峰值應力。
  16. Abstract : through extending the wear plate at the saddle and using the flexible saddle, the circumferential peak stress at the joint of the shell and the saddle can be decreased efficiently

    文摘:本文介紹通過鞍座上墊板的伸出和採用柔性鞍座，即能有效地降低鞍座邊角處的環向峰值應力。
分享友人
分享到 Line

分享到臉書