closed feed system 中文意思是什麼
closed feed system
解釋
閉路供電系統-
In this system, the closed loop is composed of velocity measurement machine used as velocity feedback and coder used as position feedback, the feed - forward signal of ship swaying is measured by rate gyro
該系統用測速機構成閉環，作速度反饋，編碼器作位置反饋，速率陀螺測量並前饋艦船搖速度信號。 -
At the same time we based on the high precision tuning mechanism and computer controlling feed - back technology to design pid controller. so, we finished design of closed - circuit controlling system and achieved the goal of sampling and feedback
同時，本文在高精度的調諧機構的基礎上，利用計算機控制反饋技術，設計了速度式pid控制器，完成了閉環反饋控制系統的設計，實現了輸出參量光信號採集和反饋的目的。 -
In the section of experiment, we focused on the research of optical system of optical parameter oscillation, computer controlling data sampling closed - circuit system and technology of computer controlling feed - back. in the section of optics, we used present condition to do the experiments about optical parameter effect and got a series of characteristic curve on power transition efficiency and output power
本文的實驗部分主要側重於智能化光參量系統的光學部分、計算機控制數據採集閉環系統以及計算機控制反饋技術的研究。在光學部分，本論文利用現有實驗條件進行了參量振蕩器頻率調諧的研究，得到了調諧曲線，並做了輸出參量光的能量轉換效率以及輸出功率的實驗，得到一系列特性曲線。 -
To realize the large stroke microfeed in this feed system, the microfeed system of closed - loop feedback control was adopted. the system is controlled by the 89c5 1 singlechip computer and combinely driven by the stepmotor and piezoelectric ceramic, the worktable ? position is measured by the raster position sensor
為滿足進給系統能實現大行程的微量進給的要求，系統採用了由89c51單片機控制，由步進電機和壓電陶瓷復合驅動，並通過光柵位移傳感器進行位移檢測，從而形成閉環反饋控制的微量進給方式。 -
After analyzing compensation conditions for 3 - axis stabilization to overcome disturbance from ship surge, sway and yaw, two control strategies - feed - forward compensation and closed - loop feedback compensation - are given. these two strategies are applied to antenna stabilized tracking system with good performance. intelligent pid is used in closed - loop feedback compensation to get high tracking precision and rapid response
重點分析了天線穩定控制系統的三軸補償條件，提出了穩定系統抑止載體擾動的控制策略：對于橫滾和俯仰系統採用前饋補償的控制策略；對于方位系統，在以步進電機為驅動元件的特定條件下，研究了變控制周期的閉環反饋策略，同時成功將智能pid演算法應用於實際系統，提高了系統的跟蹤精度和響應快速性。 -
The algorithm of strapdown inertial navigation system is also discussed and then use the flight - track generator to give a simulation, since a closed loop feedback integrated navigation system is designed in this paper, and the output of the filter must feed back to the strapdown inertial navigation system, the analysis of the algorithm in strapdown inertial navigation system is important. the scheme to design the trajectory of gps and the simulation of gps constellation are then studied, the simulation of gps constellation is given from the calculation of vernal equinox base on the principle of celestial mechanics, this method of different from other methods given by other paper and is useful to the research of satellite navigation system. a new method to abstract noise modal in integrated navigation system is proved to be useful in practice, this method, which is given by use the principles of stochastic processes, statistics, time series analysis, and system identification, is suitable for the kalman filter in integrated navigation system
如航跡產生器的設計，該航跡產生器是研究組合導航問題的前提，從國外一些研究組合導航系統的文獻中可以看出，設計這樣一個航跡產生器是非常必要的，所以本文自行設計了這樣一個系統；還討論了捷聯慣性導航系統中捷聯解算的方法，並進行了模擬研究，由於在本文設計的閉環反饋式組合導航系統中，對捷聯慣導系統的平臺誤差進行閉環控制，需要將濾波器輸出的校正量反饋到捷聯解算內部，所以必須對捷聯解算進行深入的研究和分析，更何況捷聯解算問題本身也是導航界的一個熱門研究課題；另外，本文還介紹了gps軌道及其星座模擬的設計思想和方案，與以往gps軌道和星座模擬不同的是本文從天體力學中計算春分點開始，逐步進行gps軌道及其星座模擬，這樣的設計方法對從事衛星導航的研究工作是有價值的；還對組合導航中誤差建模方法進行了研究，綜合運用隨機過程、概率統計、時序分析及系統辯識等方面的理論提出了一套適合組合導航卡爾曼濾波的誤差建模方法，並運用實際研究工作中的測量數據對該方法進行了驗證。 -
Piston ring is the important accessory of the engine and turning its contour is the key procedure to ensure the performance of piston ring it has great value in economy and society that we develop the nc machining system for outer circle of piston ring to manufacture the high quality piston ring and to replace the import machine according to piston ring contour data provlded by the cad system ， it can turn the piston ring contour by controlling the displacement of servomechanism which is controlled by the angle of servo motor it uses the theories of velocity closed loop 、 dlsplacement closed loop and feed forward control to improve the control precision of system on the basis of theories of elastic mechanics and mathematics ， the cad system can provide the accurate data required by the nc machine system according to the calculation model and the parameters of piston ring this system integrates the cad cam technology
系統根據活塞環cad系統生成的介面數據，通過伺服電機的轉角位置控制自主研製的高性能微位移進給機構產生給定的位移，以完成活塞環輪廓的仿型加工。系統採用速度、位置閉環控制及前饋控制理論，以提高系統的控制精度。活塞環cad系統以彈性力學和數學方法為基礎，根據常用的計算模型與活塞環參數自動生成數控加工系統所需的精確的介面數據，實現cad / cam一體化。
分享友人