closed position 中文意思是什麼

closed position 解釋
（門）關閉位置
  • closed : adj. 1. 關閉著的，封閉著的；密閉著的；保密的。2. 〈美國〉準備好了的；定了契約的。3. 【語音】閉音節的。
  • position : n 1 位置；方位；地點。2 處境，情況；狀態，形勢，局面。3 姿態，姿勢。4 地位，身份；職位；職務。5 ...
  1. Open the needle valve 2 _ turns from the fully closed position

    鎖緊主油針到底，放開2圈。
  2. The throttle plate moves toward the closed position as rated speed is reached.

    當達到發動機額定轉速時，節流板趨于關閉位置。
  3. The adjusting of screw prevents the throttle valve from moving to the fully closed position.

    調節螺釘防止節氣門運動到全關閉位置。
  4. Insert stem into stem opening and press in to full - closed position

    將閥桿插入閥桿開口處，並將其壓進全閉的位置。
  5. Insert stem assembly ( a ) and hold disc on seat ring in closed position, as shown

    插入閥桿總成（ a ） ，並在關閉狀態下握住閥座環上的閥瓣，如圖所示。
  6. Non - preferred would try to push the disc away from the seat while it is in the closed position

    非優先定向則當閥門處于關閉狀態時，試圖將閥板推離閥座。
  7. Position indicators allow at - a - glance determination of whether valve is in open or closed position

    位置指示器使得操作者能夠一眼看出閥門是處于開啟還是關閉的位置。
  8. Reduced maintenance is assured because the disc is the only moving part and is designed to minimize flutter in the closed position, thus reducing wear on the pivot pin, disc, and seat

    確保節省維護費用，因為閥瓣是唯一的一件活動部件，這種結構將關閉位置的振動減小到最小程度，因此減少了樞軸銷、閥瓣和閥座的磨損程度。
  9. Two - piece, cast bronze construction. the nibco t585 - 70 - sv ball valve provides positive energy isolation. with the valve in the closed position the down stream air exhausts to the atmosphere

    兩件式鑄青銅結構.此球閥具有很好的能量隔離性能.如果這種閥門處于關閉位置，則下游氣體將排放到大氣中
  10. In reassembly of lever handle, align the index plate so that the number one ( 1 ), indicating the full closed * position, is at right angles to the bore of the valve

    在組裝杠桿手柄時，對準刻度板，使其指示全閉位置的數字1位於閥門閥腔上的準確位置。
  11. Standing clear of the outlet ( discharged water may be hot ), slowly lift and release the lever handle on the temperature and pressure relief valve to allow the valve to operate freely and return to its closed position

    經常清洗出口（排泄水可能是熱的） ，慢慢提起並釋放降溫減壓安全閥上的杠桿手柄，使得閥門能夠靈活工作並恢復到關閉位置。
  12. For both the fully back seated and fully closed position, it is recommended that the stem be backed off 1 / 8 " to 1 / 4 " turn to prevent the stem from " growing ", bending or causing thermal binding

    對于完全後座支撐和完全關閉位置，建議閥桿後退1 / 8 "到1 / 4 "轉，以防止閥桿」生長「 ，彎曲或產生熱彎曲。
  13. Means are provided to disconnect all conductors from the service - entrance conductors and to indicate whether it is in the open or closed position

    提供切斷連接電源開關導體的各種手段並標明其開啟或關閉位置
  14. Specification for electrically operated automatic gas shut - off valves fitted with throughput adjusters, proof of closure switches, closed position indicator switches or gas flow control

    裝有流量調節器閉路開關檢驗閉合位置指示開關或氣流量控制器電動式氣體自動關閉閥規范
  15. By ensuring that all inner surfaces of the valve are kept constantly wetted and vented to the upstream side when the valve is in the closed position, we have eliminated the conditions required for gas accumulation and caustic crystallization in the body cavity

    為了確保所有閥門的內部表面能夠經常保持濕潤狀態，並在閥門關閉期間能將次氯酸鈉排出到上游位置，我們已經消除了閥腔內氣體積累和結晶體產生的必要條件。
  16. Leaving the valve in a fully closed position helps prevent weld spatter from falling directly onto the mating faces of the seats

    保持閥門處于完全關閉狀態，有助於防止焊花飛濺直接落到閥座連接面上。
  17. Leaving the disc in a fully closed position firmly closed also prevents weld spatter from falling directly onto the mating faces of the seat and disc

    保持閥瓣處于完全關閉位置也能夠避免焊花直接掉在閥座和閥瓣的連接面上。
  18. Note : the valve is shipped in the closed position. the indicator on the plastic sleeve is aligned with the vertical scribed line on the stem

    注意：閥門裝運時是處于關閉位置。塑料套筒上的指示器與閥桿上的垂直刻線對齊。
  19. The indexing pawl advances a fastener into operative engagement with the feed pawl upon movement of the second canister portion from the open position to the closed position

    當第二筒部從打開位置移動到關閉位置時，分度棘爪使緊固件前進並使其與進給棘爪工作嚙合。
  20. Load contacts 5 - 6 and 7 - 8 will also change from their normally open or normally closed position when the control energizes

    當控制裝置激活時，負荷端子5 - 6和7 - 8將也改變正常開啟或正常關閉狀態。
分享友人
分享到 Line

分享到臉書