coating efficiency 中文意思是什麼

coating efficiency 解釋
塗漬效率
  • coating : n. 1. 被覆，表皮，塗層；包覆物；（食品上的）面衣，糖衣；塗料。2. 上衣料；細呢，花呢。
  • efficiency : n. 1. 功效。2. 效率；效能；實力，能力。3. 【物理學】性能。
  1. Current density and electroplating velocity has line relation, but the increscent multiple of electroplating velocity is smaller than that of current density. which indicate that current efficiency decreases with the increase of current density at alcb + lialh4 system. at l - 5a / dm aluminum coating is dense and uniform, especially at 2. 5a / dm

    電流密度與電鍍速度兩者近似成直線關系，但電鍍速度增大的倍數比電流密度增大的倍數要小，說明在alcl _ 3 + lialh _ 4體系中隨著電流密度的提高，電流效率逐漸降低。
  2. The suitable additives recombination can not only improve considerably the quality of chromium coating, increase the brightness, current efficiency, dispersion ability and sedimentation velocity, but also enlarge the application scope of chromium plating technology

    採用適當的添加劑復合不僅可以顯著提高鍍鉻層質量，增加光亮度、電流效率、分散能力和沉積速度，而且可以擴大鍍鉻工藝范圍。
  3. Using contrast and orthogonal experiment methods, the effect of electrolyte formulae for varied concentration of cr03 and technology of chromium plating on coating property was studied systematically in this paper. primary factors and their interrelations, which influence the brightness of coating, the current efficiency, dispersion ability and sedimentation velocity of electrolyte were discovered

    本文採用對比試驗和正交試驗等方法系統地研究了低、中、高三種不同鉻酐濃度的鍍鉻液組成和鍍鉻工藝對鍍鉻層性能的影響，找到了影響鍍層光亮度、鍍液電流效率、分散能力和沉積速度的主要因素及其相互關系。
  4. Determination of the transfer efficiency of atomising and spraying equipment for liquid coating materials - flat panels

    液態塗層材料用霧化及噴塗設備輸送效率的測定.平板條
  5. Determination of the transfer efficiency of atomising and spraying equipment for liquid coating materials - part 1 : flat panels

    液體塗層材料用霧化和噴射設備轉換效率的測定.第1部分:平板
  6. Determination of the transfer efficiency of atomising and spraying equipment for liquid coating materials - part 1 : flat panels ; german version en 13966 - 1 : 2003

    液態塗層材料用霧化及噴塗設備輸送效率的測定.第1部
  7. Our company adopts the metal honeycomb or the metal network board carrier, with special coating coating technology and processing technology, prepare different forms, the all kinds of catalysiseses of specification, used in petrol exhaust. with the characteristic of light in low temp, purification efficiency high and long life etc. main technological schemes as below

    通用汽油機凈化器我公司採用金屬蜂窩或金屬網板載體，通過特殊的塗層塗覆技術及加工工藝，可制備不同形狀規格的各類催化凈化器，用於汽油機的排氣凈化，具有起燃溫度低凈化效率高使用壽命長等特點。
  8. Important features of mitex rollers include : long service life and cost efficiency ; high chemical resistance ; extreme high operating temperatures ; best running properties at high speed ; dynamic endurance ; excellent wear and cut resistance ; minimal hardening and glazing ; excellent coating and transfer characteristics ; and adjustable electrical properties

    Mitex輥產品優點：在高速度下保持優異性能；使用壽命長，效率高；抗化學腐蝕；超耐高溫；耐磨；最低限度的硬化和磨光；優異的塗布和轉移性能；精確的電導率。
  9. Porous coating graphite mould of round and special profile ( for horizontal continuous casting of medium - size and small profiled materials, incrdase work efficiency )

    多孔圓形、異形塗層石墨模具，用於中、小型的型材水平連續鑄造，可有效提高工效。
  10. The thesis introduces the development of coating glasses and expatiates the developing trends of energy save coating glasses in future : low cost materials, high efficiency making technology, high quality and good function. ce02 - tioz complex films have received abroad attention as their high reflective index, excellent ultraviolet ray ( uv ) absorbing properties, high charge - storage capacity and good electrochemical reversibility

    本論文介紹了綠色鍍膜玻璃的發展，對各類別節能鍍膜玻璃膜系結構、光性能特點以及鍍膜玻璃的制備方法進行了概括，闡述了未來綠色鍍膜玻璃的發展趨勢：採用低成本原材料和高效方便的制備工藝，制備具有復合型多功能薄膜具有更強的市場競爭力。
  11. When deposition current density was increased, w content in the coating was raised and deposition current efficiency decreased

    隨著沉積電流密度的提高，鍍層中w的含量增大，而沉積電流效率降低。
  12. Preparing anti - reflective coating and hydrogen passivation are two key procedures in the process of high efficiency crystalline silicon solar cells

    減反射膜的制備和氫鈍化是制備高效率的晶體硅太陽電池的非常重要工序之一。
  13. ( 5 ) conventional, two dimension ( agarose coating ) and three dimension ( agarose embed ) culture system were compared in their efficiency of supporting follicle growth

    （ 5 ）比較了普通培養法、二維培養法（瓊脂糖鋪底）和三維培養法（瓊脂糖包埋）的水牛腔前卵泡培養效果。
  14. Seen from the experiment result, it is clear that the deposited coating obtained with the trivalent chromium electrodepositing method we use is smooth, homogeneous, dense, and has good unti - erosive ability, high stiffness. the color ol ihe deposited coaling ol irivalent chromium is similar with that of hexavalent chromium. further more, this process has a good ability of homogeneous and deep depositing with simple facility, high current efficiency, and wide working current flow and even more it avoids environmental pollution

    實驗結果表明，本文採用的三價鉻鍍鉻方法能電鍍出鍍層光滑、均勻、緻密、抗蝕性好、硬度高的鍍層，而且解決了鍍層顏色的問題，使三價鉻鍍層不僅具有現行六價鉻鍍層的天藍色光澤，同時還具有電流效率高、均鍍能力與深鍍能力好、工作電流密度寬、設備簡單、無環境污染等特點。
  15. Golden future series of intellectual coater developed by the company adopts numerical control coating system introduced from foreign countries and can meet strict requirements for airproof performance in aviation, spaceflight, ship, saloon car, engine, motor and manufacture of machine tool. it s really ideal equipment taking the place of artificial work in coatong and sealing procedure and to improve product quality and working efficiency

    公司研製開發的金未來系列智能塗膠機是引進國外先進技術開發的數控塗膠系統，可以滿足航空航天船舶轎車發動機摩托車及機床製造等對產品的密封性能的嚴格要求，是塗膠密封工藝環節中取代手工作業，提高產品質量和工作效率的理想設備。
  16. Abstract : the causes for low efficiency of the heater in no. 2 crude unit of jpc refinery are described and analyzed including water leaking of steam soot blower, dew point corrosion caused by steam, soot deposits in convection chamber owning to poor soot blowing, high flue gas temperature, no heat recovery of flue gas, and poor performance of insulation lining, etc. by using sonic soot removing system, flue gas recovery system, spray coating of fiber and rock wool, as well as adjustment of flow scheme accordingly in the technical revamping. the dew point corrosion is completely eliminated, the insulation performance is improved, the heat loss is reduced by 1. 25 %, the flue gas temperature is reduced to about 170, and the heater efficiency is increased from 83 % to more than 90 %

    文摘:分析了金陵石油化工公司煉油廠二套常減壓裝置加熱爐存在的因蒸汽吹灰器漏水，蒸汽引起露點腐蝕及吹灰效果差造成對流室積灰，排煙溫度高，煙氣熱量未回收利用以及爐子保溫襯里效果差等問題，提出採用聲波除灰系統、煙氣回收系統、纖維噴塗和巖棉噴塗及相應的流程調整等改造措施.測定結果表明，本次技術改造解決了因蒸汽吹灰器漏水所造成的露點腐蝕問題，提高了保溫效果，減少散熱損失1 . 25 % ，排煙溫度降至170左右，裝置的爐效率由83 %左右提高到90 %以上
  17. The causes for low efficiency of the heater in no. 2 crude unit of jpc refinery are described and analyzed including water leaking of steam soot blower, dew point corrosion caused by steam, soot deposits in convection chamber owning to poor soot blowing, high flue gas temperature, no heat recovery of flue gas, and poor performance of insulation lining, etc. by using sonic soot removing system, flue gas recovery system, spray coating of fiber and rock wool, as well as adjustment of flow scheme accordingly in the technical revamping. the dew point corrosion is completely eliminated, the insulation performance is improved, the heat loss is reduced by 1. 25 %, the flue gas temperature is reduced to about 170, and the heater efficiency is increased from 83 % to more than 90 %

    分析了金陵石油化工公司煉油廠二套常減壓裝置加熱爐存在的因蒸汽吹灰器漏水，蒸汽引起露點腐蝕及吹灰效果差造成對流室積灰，排煙溫度高，煙氣熱量未回收利用以及爐子保溫襯里效果差等問題，提出採用聲波除灰系統、煙氣回收系統、纖維噴塗和巖棉噴塗及相應的流程調整等改造措施.測定結果表明，本次技術改造解決了因蒸汽吹灰器漏水所造成的露點腐蝕問題，提高了保溫效果，減少散熱損失1 . 25 % ，排煙溫度降至170左右，裝置的爐效率由83 %左右提高到90 %以上
  18. Theoretical analysis and experimental results showed that the high emissivity coating speeds up the heat - absorption and heat release process, strengthens heat transfer by radiation and heat conduction in the regenerator, improves heat transfer efficiency and the blast temperature

    理論分析和實驗結果表明，熱風爐蓄熱體表面高發射率塗層可以提高蓄熱體的蓄熱和放熱能力，強化爐內輻射傳熱和蓄熱體的導熱，從而提高熱風溫度。
  19. The structure, coating, energy efficiency, etendue of scr color wheel system was analyzed and improvements toward them were made

    對scr色輪分色合色系統從結構、膜系、光能利用率和etendue量幾個方面進行了研究，並提出了改進設計。
  20. Abstract : the in servie tubular heaters built early in refineries and chemical plans have low thermal load and low heat efficiency, therefore measures for technical reform are offered, including ( 1 ) enlarging the surface area of convection tubes to increase the thermal load of rhe convection section ; ( 2 ) increasign the heat interchanging area of radiant tubes ; ( 3 ) changing the height of the chimney ; ( 4 ) using new burner with forced air supply to increase calorific capacityu ; ( 5 ) adding air preheater between the convection section and chimney to enhence the temperature of the air entering the furnace ; ( 6 ) adopting high temperature radiant coating to improve the effect of radiant heat interchanging

    文摘:針對早期建造的煉油廠和化工廠在役管式加熱爐熱負荷和熱效率低的狀況，提出了若干技術改造措施包括，增大對流管表面積以增大對流段的熱負荷；增加輻射管的換熱面積；修正煙囪高度；換用新型燃燒器，變自然通風為強制供風，以增大燃燒器的發熱量，減小過剩空氣系數，節省燃料2 % 3 % ；在對流段和煙囪之間增設空氣預熱器以提高空氣入爐溫度；採用高溫輻射塗料增強輻射換熱效果，從而增加熱源對爐壁的輻射傳熱量和爐管的傳熱量等。
分享友人
分享到 Line

分享到臉書