combustion spiral 中文意思是什麼
combustion spiral
解釋
燃燒旋管- combustion : n. 1. 燃燒，發火，點火。2. （有機體內營養料的）氧化。3. 騷動。
- spiral : adj 1 螺旋形的，盤旋的，盤旋上升的。2 【數學】螺線的。n 1 螺旋形物。2 螺簧；【物理學】螺線。3 【...
-
Numerical simulation by cfd was carried out to understand the hot current behavior in a tunnel with longitudinal ventilation. it becomes clear that fire source modeling is very important because the hot current behavior is strongly affected by the fire source position and is sensitive to methods in the modeling of the fire source. the flame area which has developed from the fire source is an area of chemical reaction caused by combustion. even if grids in the vicinity of the fire source are made fine, it was difficult to simulate the heat generation area with consideration to this chemical reaction through using a method for setting the heat release rate simply on the fire source surface. therefore, we proposed a method adopting the knowledge on flame shape under the longitudinal ventilation and incorporating it into numerical simulation and it showed a good agreement with the experimental results. it was shown through experiments in a tunnel with longitudinal ventilation that the hot current developed toward the tunnel center downwind from the fire source near a wall. the cause was investigated by numerical simulation and it became clear from the results that the spiral air by the fire plume created a vortex in the crevice between the wall and the plume
運用cfd進行數字模擬，以了解縱向通風隧道內熱煙氣流的特性.通過模擬發現對火源進行模擬非常重要，熱煙氣流特性受火源位置的影響很大，並且對火源模擬方法很敏感.火源生成的火焰區是燃燒引起的化學反應區域.即使火源附近的木垛排列完好，也很難在考慮這些化學反應條件下模擬熱生成區域.建議考慮縱向通風隧道內火焰形狀並對它進行數字模擬.模擬結果與試驗結果非常吻合.試驗證明，在縱向通風隧道內，熱煙氣流從靠近墻體火源處順風向隧道中心蔓延.數字模擬結果發現，火災羽流造成的螺旋上升空氣會在墻體和羽流之間形成一個渦流區 -
Abstract : numerical simulation by cfd was carried out to understand the hot current behavior in a tunnel with longitudinal ventilation. it becomes clear that fire source modeling is very important because the hot current behavior is strongly affected by the fire source position and is sensitive to methods in the modeling of the fire source. the flame area which has developed from the fire source is an area of chemical reaction caused by combustion. even if grids in the vicinity of the fire source are made fine, it was difficult to simulate the heat generation area with consideration to this chemical reaction through using a method for setting the heat release rate simply on the fire source surface. therefore, we proposed a method adopting the knowledge on flame shape under the longitudinal ventilation and incorporating it into numerical simulation and it showed a good agreement with the experimental results. it was shown through experiments in a tunnel with longitudinal ventilation that the hot current developed toward the tunnel center downwind from the fire source near a wall. the cause was investigated by numerical simulation and it became clear from the results that the spiral air by the fire plume created a vortex in the crevice between the wall and the plume
文摘:運用cfd進行數字模擬，以了解縱向通風隧道內熱煙氣流的特性.通過模擬發現對火源進行模擬非常重要，熱煙氣流特性受火源位置的影響很大，並且對火源模擬方法很敏感.火源生成的火焰區是燃燒引起的化學反應區域.即使火源附近的木垛排列完好，也很難在考慮這些化學反應條件下模擬熱生成區域.建議考慮縱向通風隧道內火焰形狀並對它進行數字模擬.模擬結果與試驗結果非常吻合.試驗證明，在縱向通風隧道內，熱煙氣流從靠近墻體火源處順風向隧道中心蔓延.數字模擬結果發現，火災羽流造成的螺旋上升空氣會在墻體和羽流之間形成一個渦流區 -
Other content in this paper is the design and investigation of spiral inlet port. the geometries that compose intake port have been repeatedly when intake port scheme was designed. the intake port scheme has been carried out steady - flow test. the experiment data has been analyzed and investigated, then the performance of inlet port has been estimated by the fluid coefficient and the whirl ratio. at last, the spiral inlet port scheme has been selected based on matching relation of the factors of combustion system. in addition, how to " intake port synthesis performance coefficienf ' evaluate engine intake port has been discussed
本文的另一項內容是螺旋進氣道的設計和研究。通過對進氣道的幾個主要結構參數進行反復修改擬定進氣道方案，並對其進行穩流試驗，分析和研究試驗數據，利用流通系數、渦流比進行進氣道性能評估，根據燃燒系統要素的匹配關系，確定了兩種螺旋進氣道方案。另外，本文探討了「進氣道綜合性能系數」對發動機渦流進氣道性能的評估能力。 -
Spiral flow is widely used in industry, e. g. in jet technology, combustion technology, pneumatic transportation, cyclone separators. researchers have done a lot of investigations about spiral flow
螺旋流在工業方面有廣泛的應用，如在射流技術、燃燒技術、氣力輸送、旋風分離、內燃機等方面均應用了螺旋流，各國研究者對螺旋流進行了廣泛的研究。
分享友人