common-mode resistance 中文意思是什麼

common-mode resistance 解釋
共模電阻
  • common : adj 1 共通的，共同的，共有的。2 公眾的；公共的。3 普通的，通常的，尋常的，平常的。4 平凡的，通俗...
  • mode : n 1 法，樣，方法，方式。2 模，型；樣式，體裁，款式；習慣。3 風尚；〈the mode〉流行，時髦。4 【語...
  • resistance : n. 1. 抵抗，反抗，抗拒，抵禦；敵對，抵抗力，反抗力，阻力，【生物學】抗病性。2. 【電學】電阻；阻抗；電阻器。
  1. Fourthly, according with the analyzing of flow measurement, we research the main problems needed to be solve in the process of measurement, such as analysis and measurement of the internal resistance, selection of excitation frequency, stable signal datum mark and restraining common mode interference, restraining for serial mode interference and working frequency interference ; transporting and shielding the flow signal, constant current excitation and magnetic field equalizing, flow measuring

    第四，根據對流量測量問題分析的，深入研究了設計過程中需要解決的主要問題。如內阻分析與測量;勵磁頻率的選擇;穩定信號基準點與抑制共模干擾;串模干擾與工頻干擾抑制;流量信號傳輸與屏蔽;恆流勵磁與磁場補償;流量測量點的選擇等。
  2. The thesis has done the widespread investigation and study to the domestic and foreign ’ s technologies of analogy low voltage and low power, and analyzes the principles of work, merts and shortcomings of these technologies, based on the absorption of these technologies, it designs a 1. 5v low power rail - to - rail cmos operational amplifier. when designing input stage, in order to enable the input common mode voltage range to achieve rail - to - rail, it does not use the traditional differential input pair, but use the nmos tube and the pmos tube parallel supplementary differential input pair to the structure, and uses the proportional current mirror technology to realize the constant transconductance of input stage. in the middle gain stage design, the current mirror load does not use the traditional standard cascode structure, but uses the low voltage, wide - swing casecode structure which is suitable to work in low voltage. when designing output stage, in order to enhance the efficiency, it uses the push - pull common source stage amplifier as the output stage, the output voltage swing basically reached rail - to - rail. the thesis changes the design of the traditional normal source based on the operational amplifier, uses the differential amplifier with current mirror load to design a normal current source. the normal current source provides the stable bias current and the bias voltage to the operational amplifier, so the stability of operational amplifier is guaranteed. the thesis uses the miller compensate technology with a adjusting zero resistance to compensate the operational amplifier

    本論文對國內外的模擬低電壓低功耗技術做了廣泛的調查研究，分析了這些技術的工作原理和優缺點，在吸收這些技術成果基礎上設計了一個1 . 5v低功耗軌至軌cmos運算放大器。在設計輸入級時，為了使輸入共模電壓范圍達到軌至軌，不是採用傳統的差動輸入結構，而是採用了nmos管和pmos管並聯的互補差動輸入對結構，並採用成比例的電流鏡技術實現了輸入級跨導的恆定;在中間增益級設計中，電流鏡負載並不是採用傳統的標準共源共柵結構，而是採用了適合在低壓工作的低壓寬擺幅共源共柵結構;在輸出級設計時，為了提高效率，採用了推挽共源級放大器作為輸出級，輸出電壓擺幅基本上達到了軌至軌;本論文改變傳統基準源基於運放的設計，採用了帶電流鏡負載的差分放大器設計了一個基準電流源，給運放提供穩定的偏置電流和偏置電壓，保證了運放的穩定性;並採用了帶調零電阻的密勒補償技術對運放進行頻率補償。
  3. While low voltage and low power is realized when designing the operational amplifier in this text, great efforts have been devoted to increasing the input common mode range and the swing of output signal, and lowing the output resistance at the same time

    只是實現低壓低功耗而不實現良好的性能顯然是錯誤的。本文在設計實現低壓低功耗的運算放大器的同時，也想法提高輸入共模範圍和輸出信號的幅度，同時降低輸出阻抗。
分享友人
分享到 Line

分享到臉書