compensation of instrument 中文意思是什麼

compensation of instrument 解釋
儀器補償
  • compensation : n 賠償；補償（金）；報酬 （for）；〈美國〉薪水，工資 （for）; 【機械工程】補整；【造船】補強。com...
  • of : OF ＝Old French 古法語。
  • instrument : n 1 儀表，儀器 〈cf tool implement〉。2 樂器 （＝musical instrument）。3 【法律】證件，證券，文件...
  1. As a kind of variometer, fluxgate magnetometer should has high observation precision as well as long - term stability and favorable temperature features. the compensation technology is the key for the performance of fluxgate magnetometer. this paper made an introduction about the compensation principle of fluxgate instrument

    作為相對觀測的磁通門磁力儀，不僅要求其觀測精度應滿足要求，而且還要求儀器具有長期穩定性和良好的溫度特性，而對磁通門磁力儀的長期穩定性和溫度特性有重要影響的部分就是儀器的補償部分。
  2. In general, a precise resistor is in series with one of the resistors in wheatstone bridge to compensate the zero offset, and the other one is in parallel with another arm of the wheatstone bridge to compensate thermal zero drift. based on this principle, in this paper, a compensation method based on virtual instrument technology has been put forward. actuated by current source, a good calculation method of compensation resistors and their position in the bridge is deduced

    本文基於串並聯電阻補償法的原理，提出了一種基於虛擬儀器的誤差補償方案，推導了在恆流源供電下可以精確的計算出補償電阻大小和補償位置的演算法，並且在虛擬儀器軟體平臺labview上完成了數據採集、處理、顯示等軟體的設計，經過實驗的驗證，對傳感器的零點溫度漂移補償取得較好的效果，而對靈敏度溫度漂移的工藝補償亦有一定的效果。
  3. In instrument such as anemometer and electric meter, the compensation ability of magnetic temperature compensation materials to the permanent magnets determines the apparatus ' s accuracy

    摘要在風速表、電度表等儀表中，磁溫度補償材料對永磁體補償能力的大小決定了儀表的精度。
  4. In order to eliminate the influences caused by temperature, electrode - polarization and autoeciousness - capacitance, the traditional instrument has added complicated circuits so that it cause such shortcomings as big error, time - retardation and a relatively small scope. through the problems caused by 2 - probe electrode and ac current source, a new measuring circuit based on the excitation of bi - directional voltage pulse and the sensor of 4 - probe electrode is proposed, using single - chip to achieve auto - temperature compensation

    作者在參閱國內外大量相關參考文獻的基礎上，從電導測試技術的原理性研究出發，分析了採用交流激勵源、兩電導電極為傳感器的傳統電導測試系統所面臨的種種問題，提出並研製了一種基於雙極性脈沖電壓激勵、以四電導電極為探頭、運用單片機進行溫度自動補償的新型電導率測量系統。
  5. In order to improve measurement precision and display fidelity of the instrument, three new methods of nonlinear calibration of thermal instruments, which are based on intelligent control theory, are presented in this paper, such as nonlinear compensation of zr02 oxygen measurement instrument using bp nn, nonlinear calibration of temperature measurement sensors using cmac nn and nonlinear identification of throttle flow meter using ga. these methods prove to be not only simple but also effective

    火電廠熱工儀表普遍存在非線性特性，為了提高參數測量的準確度和儀表顯示的精確度，基於智能控制理論，文中提出了熱工儀表非線性校正的新方法： bp神經網路補償氧化鋯氧量計非線性特性的方法、 cmac神經網路校正測溫傳感器非線性特性的方法、遺傳演算法辯識節流式流量儀表非線性特性的方法。
  6. It emphases the selection of secondary voltage of the step - down transformer, the control and protection of thyristor, the calculation of compensation capability and group capability, the technique of cross - zero switched on / off capacitors or reactor, the solution of avoiding possible resonance in switching on / off groups of capacitors or reactor and the measure of the best time to switch ( including the design of the computer survey and control system, instrument deliver system, delay operate and protect system ). although thyristor as a no - contact switch can avoid almost the problem of contact switch with contact, it can not solve the over - voltage, over - current and transient process itself as switching on / off capacitors or reactor. so we must develop a set of thyristor - switched control and protect system with great reliability so that it can realize of cross - zero switching on / off capacitors or reactor at any time

    晶閘管具有過零、動作快速的特點，本研究以晶閘管為電容器和電抗器的分組投切開關，重點研究了協調變壓器二次電壓的選擇、晶閘管觸發控制及保護、動態補償容量及分組容量的計算確定、過零投切電容器和電抗器技術的實現、以及分組投切電容器和電抗器可能發生諧振的處理計算方法，給出實現最佳補償投切選擇方法（測控系統、儀表變送系統、操作和保護系統的設計步驟） ，研製了一套高可靠性晶閘管觸發控制及保護系統，實現對無功的靜止可調補償。
  7. This paper introduces the principle of real - time automatic gain control based on feed forwarding technology, and the realization of the critical technologies including digital compensation and synchronization, as well as, the specific application of communication analyzing instrument

    摘要闡述了基於前饋技術的實時自動增益控制的原理及同步和數字補償等關鍵技術的實現；介紹了在通信分析儀中的具體應用。
  8. Commonly, the precision of grind machine could reach to 2um after modifying and grinding for second time. so we designed and assembled this aspheric surface measuring instrument to get error function as compensation documents of grind machine to assure the precision of grind of optics

    一般來說，高精度的非球面銑磨機床經過誤差補償后其精磨面形精度的達到2um ，因此通過輪廓儀的測量得到銑磨機床一次銑磨的誤差反饋數據，就可對非球面銑磨機床一次銑磨進行補償。
  9. A series of systems including economic compensation, form the instrument and performance of the amendment and balance

    這項制度並不是「普適」的，它有著特定的適用范圍。
分享友人
分享到 Line

分享到臉書