compliance method 中文意思是什麼
compliance method
解釋
柔度法- compliance : n. 1. 應允，答應（要求等）。2. 和藹，溫和；順從，服從；盲從；【物理學】柔量；【數學】順性。
- method : n 1 方法，方式；順序。2 （思想、言談上的）條理，規律，秩序。3 【生物學】分類法。4 〈M 〉【戲劇】...
-
10 method of payment and form of payment advice. 1l instructions in case of non - payment, non - acceptance and or non - compliance with other instructions
K .發生拒絕付款拒絕承兌及或與其他指示不相符的情況時應給出的指示。 -
According to the characters of shimadzu electro hydraulic servo controlled fatigue testing machine and ct specimen, put forward a method based on compliance of stroke displacement which reflects the displacement of loading point at first time
本項研究根據島津液壓伺服材料試驗機和ct試樣的特點，首次提出了基於通過測量反映加載點位移的試驗機活塞位移的卸載柔度法來測量裂紋長度。 -
A common recognized method for the shaft alignment, is to set up a physical model, and appropriately locate each bearing in compliance with the required bearing load, stress and shear force and slop etc, so as to fix the shaft with the curve line as required and obtain a right distribution of bearing load
對于軸系校中計算，國內外比較通用的方法是對軸系相關的要素進行處理，建立物理模型，按照規定的軸承負荷、應力，轉角等限制條件，確定各軸承的合理位置，將軸系安裝成規定的曲線狀態，以達到使各個軸承上的負荷合理分配。 -
Evaluation of residual stresses in 7075 aluminum alloy plate using crack compliance method
裂紋柔度法在7075鋁合金板殘余應力檢測中的應用 -
The particular advantage of the compliance measurement method is that the loading fixtures used can be identical to those needed for fracture tests or crack-propagation tests of materials.
柔度測量法的特殊優點是可以使用材料斷裂試驗或裂紋擴展所用的加載夾具。 -
The dcb ( double cantilever beam ) met hod to test the interlaminar toughness of fabric - reinforced laminates and the modified compliance calibration method ( mcc ) were adopted in this research. the double cantilever beam ( dcb ) test was executed for stitched laminates to evaluate the interlaminar fracture toughness. the stitch parameters ( stitch line spacing and pitch spacing ) were changed and their effects on interlaminar fracture toughness were examined by means of dcb test by using improved insert type loading fixture
試驗中採用改進的插入型夾具、雙懸臂梁dcb （ doublecantileverbeam ）試驗方法，測試了載荷?試樣開口位移曲線，依據改進的柔度梁方法（ modifiedcompliancecalibrationmethod （ mcc ） ）計算出了各個試樣的層間斷裂韌性（ r曲線）及層間斷裂韌性的平均值，闡明了縫合工藝參數與層間斷裂韌性（ g _ （ ic ） ）間的關系，以拉伸與彎曲強度為約束條件，以層間斷裂韌性值為目標優化了縫合工藝。 -
During the test procedure, the compliance test method is adopted to increase the load cyclically until the crack extends over the height of the specimen. then the record data are rationally smoothed and calibrated for next use, at the same time, the response on the tail of measured curve is expressed in mathematical function to eliminate its errorous influence on gf
在測試過程中採用了柔度測試法以循壞的方式增加荷載直到試件完全斷開，然後對試驗曲線進行了合理的光滑處理，並對試驗曲線的尾部進行了擬合表達盡量消除其對結果的誤差影響。 -
It is always desirable to obtain and compare results by both the compliance method and a numerical method because their advantages are complementary.
一般都想同時取得柔度方法和數值方法的兩種結果並進行比較，因為它們彼此能取長補短。 -
Acoustics. measurement of airborne noise emitted by power lawn mowers, lawn tractors, and lawn and garden tractors with moving attachments. method for checking compliance with noise limits
聲學.由帶割草附件的動力割草機割草拖拉機和草坪及園藝用拖拉機排放的氣載噪聲的測量.符合噪聲限制值的檢驗方法 -
Effect of regression area on fracture toughness measured by compliance method
回歸區間對柔度法測量斷裂韌度的影響 -
The effects of clearances within the connections of the mechanisms and of elastic compliance of the links and members of the device are very serious. especially to the mechanism worked in space environments, the analysis method is important
空間可動結構一個很顯著的特點是構件可動，這就表明機構由不同構件組成，構件之間必然存在著間隙，在有些情況下，間隙對可動結構的影響非常大。 -
Acoustics. measurement of airborne noise emitted by earth - moving machinery. method for determining compliance with limits for exterior noise. stationary test condition
聲學.土方機械發出的空氣中噪音的測量.室外噪音限制符合性的測定方法.靜態試驗條件
分享友人