composite rate 中文意思是什麼
composite rate
解釋
混合率-
It is inferred that the dissolution rate and dissolubility of gypsum are the main decisive factors of cement performance of portland - sulphoalminate composite system
推導證實，石膏的溶解速度和溶解度是決定硅酸鹽硫鋁酸鹽復合體系水泥性能的主要因素。 -
It showed the effluence of composite film on the permeation rate of o2 is more obvious than that of n2 and co2. but there is no apparent effect on their separation. compare with host film, thermal - infrared radiance of composite film decreased
結果表明fe3o4 / pvdf復合膜對于o2滲透速率的影響較n2 、 co2大，但對於三者分離效果不明顯；納米fe3o4的引入使得復合膜相對于pvdf基膜，熱紅外輻射率有所降低，並具有一定的電磁波吸收能力。 -
Sicp / al matrix composites, with 5, 15 and 25 % volume fraction of sic particles, were prepared by vacuum hot - pressing sintering processing in this paper. based on mechanics properties, sem observation and energy dispersive x - ray analysis, the interface reaction phenomenon of sicp / al composites made by vacuum hot - pressing sintering, as well as the reinforcement and fracture mechanisms of this composite were analyzed. the dynamic responses of sipc / al composites were studied by a split hopkinson high - speed pressure bar impact system which strain rate was from quasistatic state strain rate ( 3. 3 10 - 3s - 1 ) to dynamic state strain rate ( 5. 2 103 s - 1 )
本研究以武裝直升飛機防護裝甲材料為研究對象，採用真空熱壓粉末冶金燒結工藝制備了含sic顆粒體積分數分別為5 、 15和25的sic顆粒增強鋁基復合材料，結合其力學性能、掃描電鏡和界面微區能譜分析結果，分析了sic _ p al復合材料的真空燒結過程中的界面現象，以及材料增強和斷裂機理，並利用hopkinson高速壓桿沖擊實驗系統對其從靜態到動態（應變率為3 . 3 10 ~ （ - 3 ） s ~ （ - 1 ） 5 . 2 10 ~ 3s ~ （ - 1 ） ）的壓縮破壞響應進行了研究，分析了不同體積分數sic _ p al復合材料高應變率壓縮載荷下，材料的變形和微觀損傷機理，以及利用高速沖擊空氣炮測定了改復合材料制備剃度復合板的穿透性能。 -
We make use of double complexing agents and double quickening agents in the composite plating techniques which enable to increase the deposition rate and to obtain a more stable plating bath
在復合鍍工藝中，採用雙絡合劑、雙加速劑來提高鍍速和穩定鍍液。 -
Press release : composite interest rate : end - april 2006
新聞稿：年月底綜合利率 -
Press release : composite interest rate : end - march 2006
新聞稿：年月底綜合利率 -
High strain rate superplasticity in sicp reinforced az31 magnesium matrix composite
金屬基復合材料的高應變速率超塑性 -
Abstract : by utlizing abundant local resource of ytirium and combining the characteristics of magnesium, barium, calcium and silicon, a sort of composite nodulizer - ytirium - based heavy rare earth nodulizer was developed which is characterized by its good desulphurizing and deoxidizing rate effect, excellent effect to neutralize anti - nodulizing effect of trace elements, strong nodulizng effect and degeneration - resistance, good effect to fine matrix structure, decreased chilling tendency and wide scope of applicatiom using this nodulizer to produce some important castings such as water - cooled wall of blast furnace and roller could increase mechanical properties of central area and casting yield
文摘:利用江西省豐富的釔基重稀土，結合鎂、鋇、硅、鈣等元素的特性開發了釔基重稀土復合球化劑，該球化劑具有脫硫、脫氧、抗干擾元素、球化和抗球化衰退能力強，細化基體組織，白口傾向小，適用范圍寬等特點，應用於高爐冷卻壁，軋輥等關鍵鑄件上可提高心部力學性能和工藝出品率。 -
The influence of different gypsum on strengh of portland - sulphoalminate composite cement system is complicated, related with aluminiferouse mineral in cement system and the so4 ( superscript 2 - ) concentration of its hydrated solution ; in distilled water and maximum lime wash, the dissolution rate of dihydrate gypsum is higher than that of anhydrite but the dissolubility is lower
石膏品種對硅酸鹽硫鋁酸鹽復合體系水泥強度的影響較復雜，與水泥體系中含鋁礦物及其水化溶液中so4 （上標2 - ）離子濃度有關；在蒸餾水和飽和石灰水中，二水石膏的溶解速度比硬石膏快，溶解度比硬石膏低。 -
The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film
試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。 -
The composite interest rate and best lending rates are end - of - period figures
綜合利率及最優惠貸款利率均為期末數字。 -
With the material dynamic constitutive equation including damage and the effect of stain rate the predictable formula about ballistic limit velocity of fiber composite target. secondly based on the damage feature about ceramic / fiber composite target caused by impact load, analysis model about defense performance of ceramic / composite material target is formed and the predictable formula about ballistic limit velocity is also given. lastly using the reflection and projectile theory of stress wave the paper discusses the design of ceramic / composite material target, optimizes the design of double layer ceramic / composite targets, gains optimal coefficient under certain area density and discusses the variety relationship of area density and thickness with optimal coefficient u nder some ballistic limit velocity 3
首先，分析了纖維類正交鋪層復合靶板在沖擊載荷作用下的損傷破壞機理，結合包含損傷和應變率效應的材料動態本構方程，建立了纖維復合材料板彈道極限速度的預測公式；其次，根據陶瓷/纖維材料復合靶板在沖擊載荷下的破壞特點，建立了陶瓷/復合材料靶板抗彈性能分析模型，給出了彈道極限速度預測公式；最後，利用應力波反射和透射理論討論了陶瓷/復合材料靶板的設計問題，對雙層陶瓷復合靶板的優化設計進行了分析，給出了在一定面密度下的最佳優化系數，討論了一定彈道極限速度下的面密度和厚度隨優化系數的變化關系。 -
The study on salc includes : 1 ) the study on the harmonization between aeration rate and melts thickly rate ; 2 ) the study and application of the new multi - function composite additive ( nmca ) ; 3 ) the study on the durability of salc ; 4 ) the designation of the structure of new multi - functional unbearing compound wall and fast equipment mold, etc. the results show : the additive can improve the harmonization of the workability and mechanics characteristic of salc to a certain extent ; improve the volume stability of salc under different environment by enhancing the resistance to the freeze and thaw, dry and wet circle and drying shrinkage
在salc的研究方面，主要包括發氣速度和稠化速度的協調性研究、新型多功能復合外加劑的研製、耐久性能的研究以及新型多功能非承重復合墻體結構及其澆注成型的快速組裝模具設計等內容；結果表明：科學合理的引入輔助外加劑在一定程度上使salc材料的工作性及相應物理力學性能得以最佳匹配，增強了salc材料對凍融循環、干濕循環及乾燥收縮的抵抗能力，使salc在不同的環境下均具有較好的體積穩定性。 -
The grade composite, road performance and its mechanism are systemically studied. 1 ) the aggregate grade of ogfc is studied through the volume method base on the analysis of the aggregate grades. then the grade is verified and the relation between the grade and pore rate is studied statistically, the typical grades of ogfc are developed ; 2 ) the reasonable pore rate of ogfc is studied on the basis of the balance of mechanics and function performance ; 3 ) the mineral fiber is added to the ogfc mixes to increase asphalt content, thus the anti - water performance of ogfc mixes are improved ; 4 ) high viscous asphalt fit for the preparation of ogfc is prepared through composite modification by sbs and rubber powder ; 5 ) the mechanics mechanism of ogfc is studied in the paper, it shows : asphalt paste, as well as the coarse aggregate skeleton, is essential to the mechanics of ogfc
在分析各國ogfc級配的基礎上，運用礦料體積法進行ogfc級配設計，用正交實驗對礦料級配進行了優化設計，運用數理統計方法分析礦料級配和孔隙率之間的關系，並回歸出礦料關鍵篩孔通過率與ogfc骨架空隙結構關系的數學方程，進而提出了ogfc的合理級配；通過對不同孔隙率典型級配混合料的性能研究，綜合力學和功能性能，得出了ogfc的合理孔隙率范圍：針對高速公路面層對ogfc力學性能方面的要求，本文從瀝青膠結材料、纖維穩定劑兩方面對ogfc的性能進行改善：通過sbs和橡膠粉復合改性的方法開發出了適合ogfc的高粘度改性瀝青，摻加聚合物纖維，提高ogfc的最佳瀝青用量，進而改善了混合料的高溫性能和抗水損害性能，優化設計出能滿足高速公路路用性能，車轍動穩定度達5000次/ mm以上，動融劈裂強度比90 ，透水系數31ml / s ，並具有防滑降噪功能的開級配瀝青磨耗層（ ogfc ）混合料。 -
Integrated with the correlation between natural and composite decline rates as well as the characteristic of production testing data, the model for natural decline rate is established
在此基礎上，結合一般油田的生產測試數據特點和自然遞減率與綜合遞減率的關系，建立了自然遞減率多因素分析模型。 -
The effect of solidification rate on the solidified structure, cooperation growth zone and microstructures such as tac rods volume fraction, tac rods average spacing, tac average transverse area and y phase in this eutectic composite were systematically investigated with lmc. the relationship between solidification processing controlling and solidification microstructure was established
藉助金相技術、電鏡技術、圖象處理技術等多種分析測試手段，考察試樣的界面形態、組織特徵以及共晶形貌等多方面的凝固特性，建立了凝固過程式控制制與凝固組織的對應關系。 -
And there is our suggestion of a composite rate reflecting the average cost of funds of the banks in hong kong
另一選擇就是我們建議的綜合利率，這個利率能反映本港銀行平均資金成本。 -
The 55 basis points rise in the composite rate at the end of december 2005 was primarily due to the increase in deposit rates
綜合利率于年月底上升基點，主要是由於存款利率上升。 -
Until the temporary tight liquidity condition in the interbank market returns to normal following the completion of the current ipo activities, we may see the composite rate edging up further going forward, " said mr peter pang, deputy chief executive of the hkma
至現時的公開招股活動結束而銀行同業市場流動資金短暫收緊的情況回復正常前，綜合利率或會再稍為上升。 -
Even though the banks have decided not to adopt the composite rate, we are publishing it as a reference for the banks as well as their customers. customers can of course always request their banks to price their lending by reference to the composite rate
雖然銀行決定不採用綜合利率，我們仍會編制及公布以供銀行與消費者參考，銀行客戶當然也可主動要求銀行以綜合利率來作為釐定貸款利率的參考。
分享友人