composite strain rate 中文意思是什麼
composite strain rate
解釋
復合材料應變率-
Sicp / al matrix composites, with 5, 15 and 25 % volume fraction of sic particles, were prepared by vacuum hot - pressing sintering processing in this paper. based on mechanics properties, sem observation and energy dispersive x - ray analysis, the interface reaction phenomenon of sicp / al composites made by vacuum hot - pressing sintering, as well as the reinforcement and fracture mechanisms of this composite were analyzed. the dynamic responses of sipc / al composites were studied by a split hopkinson high - speed pressure bar impact system which strain rate was from quasistatic state strain rate ( 3. 3 10 - 3s - 1 ) to dynamic state strain rate ( 5. 2 103 s - 1 )
本研究以武裝直升飛機防護裝甲材料為研究對象,採用真空熱壓粉末冶金燒結工藝制備了含sic顆粒體積分數分別為5 、 15和25的sic顆粒增強鋁基復合材料,結合其力學性能、掃描電鏡和界面微區能譜分析結果,分析了sic _ p al復合材料的真空燒結過程中的界面現象,以及材料增強和斷裂機理,並利用hopkinson高速壓桿沖擊實驗系統對其從靜態到動態(應變率為3 . 3 10 ~ ( - 3 ) s ~ ( - 1 ) 5 . 2 10 ~ 3s ~ ( - 1 ) )的壓縮破壞響應進行了研究,分析了不同體積分數sic _ p al復合材料高應變率壓縮載荷下,材料的變形和微觀損傷機理,以及利用高速沖擊空氣炮測定了改復合材料制備剃度復合板的穿透性能。 -
High strain rate superplasticity in sicp reinforced az31 magnesium matrix composite
金屬基復合材料的高應變速率超塑性 -
The compress tests on multiaxial multi - layer warp knit glass - fiber composite ( mmwk ) have also been carried out at high strain rates. the out - of - plane compressive property of multiaxial multi - layer warp knit glass - fiber composite are also rate sensitive. the maximum stress strain and elastic modulus of mmwk composite increase with the rising of strain rate
首次對多軸向經編玻璃纖維復合材料進行了高應變率下的面外壓縮試驗,實驗結果表明,多軸向經編結構玻璃纖維復合材料在面外力學性能上是應變率相關的,隨著應變率的增加,沖擊壓縮瞬時應力增加,最大應力和最大應變增加,同時初始模量也有增大的趨勢。 -
Strain rate - dependent tsai - hill strength criteria for a carbon fiber woven reinforced composite
一種碳纖維織物增強復合材料應變率相關的各向異性強度準則 -
The test results show that the out - of - plane compressive property of 3d woven composite are rate sensitive. the elastic modulus is n ' t increased with the rising of strain - rate, however, the maximum compress stress and strain of 3d woven composite increase from 228mpa to 272mpa, from 15 % to 20 % as the strain rate increases from 2000 / s to 3000 / s
實驗結果表明,三維機織玻璃纖維復合材料在面外力學性能上是應變率相關的,隨著應變率的增大,沖擊壓縮初始模量基本不變,但最大應力和最大應變都明顯增加。
分享友人