compound bending 中文意思是什麼
-
Concerning the tests, analyses, design and calculation of performances for light gauge steel framing, this paper focuses on following items : ( 1 ) the calculation of light gauge steel framed compound bearing walls ( lgsfcbw ) in compression and bending. based on north american specification and commentary for the design of cold - formed steel structural members, which was published by the american iron and steel institute, the detailed design requirements of wall stud assemblies are given considering the structural contribution of the attached sheathings and shear diaphragm is discussed briefly. then the calculational theoretic and method for sheathing braced wall stud assemblies complying with national code is brought up in compression and bending
本文圍繞輕鋼龍骨體系結構性能的試驗、分析、設計和計算，主要進行了以下四方面的研究工作： （ 1 ）輕鋼龍骨復合承載墻體的受壓、受彎計算：以美國鋼鐵協會發行的北美冷成型鋼構件設計規范及其規范說明為依據，重點考慮罩面材料對墻龍骨設計的影響，給出了目前對承重墻龍骨設計的具體要求，並對剪力蒙皮進行了簡要討論；然後提出了符合我國規范術語的剪力蒙皮作用的輕鋼龍骨復合承載墻體（即罩面支撐墻龍骨）受壓、受彎的計算理論和方法；最後對提出的計算進行簡化，使之完全與我國規范相符。 -
In practical application, the m10 180 bolts, which are installed in the head cover of the torque divider of ts5560 special automobile, sometimes fracture all of a sudden. according to the tests of acceleration, stress and strain, and the exciting test, it is resonance vibration that leads to the compound - bending fatigue fracture of the bolts. the exciting force caused by drive system, transmitted through the torque divider, produces a 1000 - 1500hz cyclical excitation at the junction of the bolts and head cover, which causes the first order bending resonance vibration of the bolts
通過加速度、應力應變測試實驗和激振試驗的研究，發現ts5560特種車分動器取力器氣缸端蓋m10 180螺栓斷裂問題是由於共振引起的雙向彎曲疲勞斷裂：傳動系統工作所產生的激勵，經過分動器結構的傳遞（特別是分動器一階扭轉模態的放大） ，在螺栓的連接處產生1000 1500hz的振動激勵，其導致螺栓一階彎曲共振，在螺栓一階彎曲模態的阻尼比較小的情況下，使得螺栓產生較大的共振響應，導致螺紋處的彎曲動應力較大，疲勞壽命較低。 -
In the third part, taking advantages of the tests of acceleration, stress and strain, the exciting test, and modal analysis method, it is found out that resonance vibration leads to the compound - bending fatigue fracture of the bolts. accordingly, a series improvement measures are proposed
第三章通過對分動器及長螺栓、短螺栓的加速度、應力應變測試分析實驗和激振試驗、模態分析研究，確定螺栓斷裂問題的根源在於共振響應導致疲勞斷裂，並提出了一系列的改進措施。 -
Mr. kong also proposed a solar energy spatial light bending down generating system, a kind of generating system that can enter and hang in the outer space which merit compound material technology, the electricity generation technology, the photoelectric control technology, the spatial tracking sunlight technology, the fuel cell technology and so on
他還介紹了在俄羅斯澳大利亞非洲馬里和中國北京建設示範樣房的進展。他還提出了在平流層高度開展光伏發電，通過自動控制在空中調整懸停姿態跟蹤太陽，提高光伏發電效率和發電量的設想。 -
The result showed when common montmorillonite, in which the mass fraction of montmorillonite was 75 %, was used as modifier, the bending modulus of the compound increased by more than 60 %, impact strength increased by a factor of 2, recovery ratio reduced 35 %, and the compound had good processability
結果表明，在採用蒙脫石質量分數為75 %的普通蒙脫土時，專用料彎曲模量提高60 %以上，沖擊強度提高一倍，回縮率降低35 % ，並且加工性能良好。
分享友人