compound control 中文意思是什麼
compound control
解釋
復合控制-
Application and research of fuzzy compound control method in aircraft deicing vehicle heating system
模糊復合控制在飛機除冰車加熱系統中的應用研究 -
The feedbacks of position, velocity, acceleration and dynamic pressure were applied to adjust the model, so the control system of single jar electrodraulic servo mechanism was built. to reduce the system error and interference error, the compound control was designed. the results of simulations showed that the magnitude attenuation and phase lag of the system come to the project demand
引入包括位置反饋、速度反饋、加速度反饋和動壓反饋在內的反饋控制技術對電液伺服驅動機構模型進行綜合校正，從而建立單缸電液伺服控制系統，並在分析系統誤差和擾動誤差后，加入復合控制減小系統誤差和抑制干擾，模擬結果表明復合控制系統的控製品質有了明顯改善，能夠滿足工程需求。 -
This thesis introduces the working principle, craftwork requirement, modeling process, control strategies and the realization of lf refining furnance bottom blowing argon control system. through the study and analysis of bottom blowing argon process control system, the thesis discusses the mean neural network model of controlled object and the mathematical models of the exectors, pwm adjustable pressure controller and pcm adjustable flux controller according to the relevant liquid knowledge and relevant data, including design data, test data and running data. to begin with the craftwork reguirement of bottom blowing argon and the actual instance of the control system, it presents the strategies of fuzzy parameters self - adaptive pid control used in pressure difference inner loop and fuzzy plus pi compound control used in flux outer loop which are based on the above modeling in order to carry out the accurate control of argon flux
本文介紹了lf精煉爐底吹氬過程式控制制系統的工作原理、工藝要求、建模過程、控制策略以及控制系統的實現。通過對精煉爐底吹氬過程式控制制系統進行研究與分析，並根據流體力學的有關知識以及有關數據（其中包括設計數據、試驗數據和運行數據） ，建立起了被控對象的平均神經網路模型和執行機構（即pwm調壓器和pcm調流器）的數學模型。在此模型的基礎上，從底吹氬工藝要求和控制系統的實際情況出發，提出了壓差內環模糊參數自適應pid控制策略和流量外環模糊pi復合控制策略，以實現氬氣流量的精確控制。 -
The computation results showed that the multi _ body system model was accuracy, the fuzzy _ pid compound control scheme was compact, both was just combined well, and this system had a good performance on improving the vehicle ' s ride comfort characteristics
計算結果表明，以多剛體系統動力學的拉格朗日方法所建數學模型模擬精度高，計算效率高，方法可行，多剛體系統動力學模型同模糊pid復合控制策略結合較好，是一個行之有效的進行綜合模擬和優化控制的系統。 -
The control method of side jet and aerodynamic compound control, including side jet and aerodynamic compound control manner, control cycle of attitude control engine, ignition logic, startup control game of attitude control engine, etc. was researched
摘要對採用燃氣動力（直接力）與氣動力復合控制技術的控制方式、姿控發動機控制周期、點火邏輯及姿控發動機啟控策略等進行了初步探討。 -
The work module of rudder was discussed and studied by simulation in side jet and aerodynamic compound control manner, the effect on guidance accuracy by control cycle of attitude control engine and action cycle of control loop was simulated
重點對採用燃氣動力氣動力復合控制方式中舵系統的工作模式進行了探討及模擬研究，對姿控發動機控制周期及控制迴路工作周期對制導精度的影響進行了初步模擬研究。 -
Simulation result showed that response time of missile was reduced and guidance accuracy was accordingly increased by side jet and aerodynamic compound control manner in terminal guidance
通過模擬研究表明：在末制導階段，採用燃氣動力氣動力復合控制方式可提高導彈的快速性，進而提高導彈的制導控制精度。 -
Part, study the model of side jet and aerodynamics compound control intercept missile
第一部分研究了直接力控制攔截導彈的模型。 -
This paper mainly works on the problem of modeling, control and guidance for a side jet and aerodynamics compound control intercept missile
本文的研究主要是圍繞著直接力和氣動力復合控制攔截導彈的建模、控制和制導所展開的。 -
It is the first that the compound control model of direct lateral force / aerodynamic control has been put forward
本文首先建立了直接側向力氣動力的復合控制數學模型。 -
The field use shows that the new apparatus is reliable and easy to control by adopting compound control pattern
現場使用證明，油管電磁無損探傷裝置採用光、機械和氣動復合控制方式，結構簡單，動作快，工作可靠，控制方便，有較好的應用效果。 -
A method to realize the compound control for disturbance compensation is put forward in this paper. the basic thought of the method is that ： obtain the ideal compensation signal no ( t ), and input the compensation signal no ( t ) to the tension servo system when the system is disturbed. compensation signal no ( t ) includes the following variables ： delay time ， compensation period ， compensation time ， compensation data. methods and procedures to obtain the compensation variables are discussed in detail in this paper. two specific means are available to realize the compensation control, and discussed in detail in this paper. in one means, the method is needed to calculate the compensation variables in real time, the linear interpolation is used here
本文提出了一種擾動復合補償控制的方法，其基本思路是：通過某種方法獲得較為理想的補償信號no （ t ） ，在系統受到擾動時，能夠向系統輸入補償信號no （ t ） ，從而達到對系統補償的目的。補償信號包括如下參量：延遲時間、補償周期、補償時間和補償數據，文中詳細論述了確定補償參量的方法及過程。提出了兩種實現補償控制的具體方式，並對兩種方式進行了詳細論述。 -
Apart from these, the paper also proposes several improvements for pump control, which include changeable cut off control that can prevent several kinds of relief loss of hydraulic system, cross sensing control of pump that can enlarge the variable working range and compound control that combine two kinds of valve control method together
此外，還提出了幾種泵控改進方案，其中包括可防止多種系統溢流狀態的可變壓力切斷控制、能增大泵的變量工作范圍的交叉功率傳感控制以及將兩種閥控策略結合在一起的復合控制技術。 -
The unfavorable factors contain complicated production technology and wayward product quality, etc. first of all, on the basis of analyzing performance index of 3 - layer pe anticorrosion, technological process and operational environment, this paper advances the synthetic control schemes that have constant compound control of temperature and feedback control of speed. considering the production process of the 3 - layer pe, because it is affected by colloidized time of fbe, relatively strong coupling exists between the temperature and speed. through the rational matching and simplifying of the variable, the system realizes uncoupling
首先在分析三層pe防腐層性能指標、工藝過程及工況條件的基礎上，提出了溫度復合控制和速度反饋控制的綜合控制方案；考慮到三層pe生產過程中，由於受fbe膠化曲線的影響，溫度和速度之間存在較強的耦合，本方案通過合理的變量搭配，實現兩種變量的解耦；文中還依據傳熱理論、中頻感應理論等提出鋼管傳熱過程理論建模的方法，經實際驗證，表現出該方案和建模方法的科學性和實用性。 -
To multi - model plants, the fuzzy integral compound control method with a self - tuning parameter is proposed. the control simulation tests of the hydraulic turbine generator are made and the results show that the proposed controller has strong robustness and satisfied performances. 4
針對具有多模型特性的受控對象，提出了一種參數自調整模糊積分復合控制方法，並以水輪機組的頻率跟蹤控制問題為背景，進行了控制系統的設計和模擬實驗研究，模擬結果表明這種新穎的控制方法具有強的魯棒性和滿意的控製品質； 4 -
A new control concept - repetitive control has been adopted. on analyzing its disadvantage, the compound control strategy based on pid and repetitive control has been put forward
在分析了它的缺點后，對其進行了改進，提出了基於pid控制和重復控制的復合控制策略。 -
This paper discusses three improving schemes : the compound control method of fuzzy control and integration control, the fuzzy control with on - line parameter self - correction, and the non - quantized fuzzy control
本文討論了三種改進的控制方案：引入積分控製作用的模糊復合控制方法，參數在線自校正的模糊控制方法以及無模糊量化方法。 -
In allusion to the coupling influence to system accuracy, this paper brings forward using dynamic robust compensation based on decoupling control. simulation experiments to prove its validity. in allusion to the performance index of simulation table, such as low velocity, high frequency response, high accuracy, etc, this paper analyzes pid control, acceleration feedback, velocity feedback, input signal differential feedforward, and employs compound control strategy including pid control, velocity feedback, position feedback and input signal differential feedforward,
針對模擬轉臺低速、高頻響、高精度等性能指標的要求，分析了pid控制策略、加速度反饋、速度反饋、輸入信號微分前饋等控制方式，採用pid控制與速度反饋、位置反饋以及輸入信號的微分前饋結合起來的復合控制策略，充分利用反饋和前饋的優勢，對轉臺的位置伺服系統進行研究。 -
Compound control action
復合控製作用 -
The results of experimentation prove that this compound control strategy brings good dynamic and static performance
實驗表明，該控制策略能較好的抑制輸出諧波，且具有較好的動態、穩態特性。
分享友人