compression beam 中文意思是什麼

compression beam 解釋
抗壓梁
  • compression : n. 1. 壓縮；壓緊；濃縮，緊縮。2. 加壓；壓抑。3. （表現的）簡練。4. 應壓試驗。
  • beam : n 1 梁，棟梁，桁條；（船的）橫梁。2 船幅；（動物、人的）體幅。3 （秤）桿，杠桿，（織機的）卷軸，...
  1. The shear mechanism, failure mode, deformation capacity, bearing capacity and the reliability of the anchored angle steels of the wrapped steel concrete cast - in - site frame typical story exterior joints under the middle and high axial compression ratio ( n = 0. 3, 0. 5, 0. 6 ), the working performance, failure mode, and the shear capacity of top story joints under the crack moment, the hysteresis characteristic and the dissipation energy capacity of the test joints are all analysed based on the 1 / 4 model pseudo - static tests of five specimens of wrapped steel concrete cast - in - site frame exterior joints, which varied in axial compression ratio, distribution of the beam angle steels and the stirrup ratio

    基於上述分析，本次試驗通過五個外包鋼混凝土邊節點1 4比例模型的偽靜力試驗，以柱的軸壓比、梁角鋼布置形式、配箍率等為主要參數，分析外包鋼混凝土現澆框架一般層邊節點在中高軸壓比（ n = 0 . 3 、 0 . 5 、 0 . 6 ）條件下，節點的抗剪機理、破壞模式、變形能力、承載能力和角鋼錨固的可靠性；分析了頂層邊節點在張開彎矩作用下的工作性能、破壞模式和抗剪承載力；分析了試驗節點的滯回性能和耗能能力。
  2. Antenna beam compression

    天線波束壓縮
  3. Beam compression factor

    波束壓縮因數
  4. In this thesis, four types of steel beam - rectangular cfst column connections, including normal welded flange plate ( wfp ) connection, bolted flange plate ( bfp ) connection, stiffened end plate ( sep ) connection and double split - tee plate ( dst ) connection, were designed based on the configuration of steel frame connection. total 8 models, 2 models of each kind of connections were tested under low - reversed cyclic loading at the end of cfst columns. the relationships between force and displacement at the end of columns, the relationships between the moment and rotation of the joints, degradations of strength and stiffness, ductility, failure mechanism and failure characteristics of these four connections under different axial - compression ratios were presented

    本文借鑒鋼框架節點構造，設計了四種類型矩形鋼管混凝土柱與鋼梁連接節點，包括常規栓焊（ wfp ）節點、翼緣全螺栓連接（ bfp ）節點、雙t板連接（ dst ）節點以及加勁端板連接（ sep ）節點，進行了四類節點8個模型試件在柱端低周反復荷載作用下的抗震性能試驗研究，比較了不同軸壓比下節點的滯回性能、強度與剛度退化、延性、破壞機理與破壞特徵，主要結論有： 1 、節點的位移滯回曲線與轉角滯回曲線為塊型分佈，沒有或略有捏攏現象，耗能能力強； 2 、軸壓比對節點滯回曲線有顯著影響，全部節點都有顯著的剛度退化； 3 、位移與轉角骨架曲線在峰值荷載後有較長的水平或下降段，具有良好的延性性能； 4 、從整體抗震性能上看，翼緣全螺栓連接節點、雙t板連接與加勁端板連接節點都優于常規栓焊節點，可在實際工程中加以推廣。
  5. ( 2 ) from the equilibrium conditions of the isolated segment from a beam - column sub - assemblage, it is clarified for the first time that the bond stress along the beam rebars passing through the joint transfers into the column end to balance shear at this column end at the same ratio as that of the compression force in the compressed concrete at beam ends

    通過對樑柱組合體柱脫離體的平衡條件，首次明確了貫穿節點梁筋粘結應力和梁端受壓混凝土的壓力以相同的比例傳入柱端以平衡柱端剪力，從而對節點區的傳力機理重慶大學博士學位論文結出了完整的和具有說服力的解釋。
  6. Then the judging method is proposed, and the proposed method can consider the stress history and viscosity shear strength of soft soil. in this paper, a fem program dpfbm1. 0 ( double plastic foundation beam method ( version 1. 0 ) ) is established. with this program, the influence of some parameters on foundation excavation is fully studied, the parameters include : compression modulus, cohesive strength, angle of internal ficiction, effective angle of internal friction, the embedded length of the wall and building load

    針對當前國內外彈性地基梁法存在的缺陷，基於對軟土流變性的研究，採取了剪應力判斷彈塑性狀態，以改進和完善基坑工程彈性地基梁法，推導了彈性狀態下地基反力系數的近似解，提出了採用剪應力組合判斷土彈簧彈塑性狀態的方法，編制了相應的彈塑性共同變形法分析程序dpfbm1 . 0 （ doubleplasticfoundationbeammethod （ version1 . 0 ） ） ，並採用該程序分析了壓縮模量、粘聚力、內摩擦角等參數變化對基坑工程的影響。
  7. The possible shear of the upper chord will change beam from flexural member to member under flexure and compression force. this is emphasised through design example. as a result ， we find that composite floor system is good for reducing the height of floor system

    在組合樓蓋體系設計中，筆者指出，可能的桁架弦桿剪力會使作為桁架弦桿側向支承的梁由彎曲構件變為壓彎構件，這是在與桁架體系相適應的樓蓋體系設計中應該注意的一個環節。
  8. Finally, an applied formula of beam ' s shear resistance is advanced when the beam ' s shear failure model is the shear - compression failure

    最後把剪壓破壞范圍內的理論抗剪公式進行簡化，提出一實用的抗剪計算公式。
  9. Make using of the critical point of the arch failure transiting to the tooth failure ( which is also the point when the non - stirrup beam ' s shear bearing capacity arrives to its minimum ) which is advanced in the arch - tooth theory of beams without shear reinforcement by g. kani and the critical point of the diagonal - tension failure transiting to the shear - compression failure which is advanced in the anti - theory, the minimum shear resistance of general bea ms which is destroyed in the range of shear - compression failure is advanced

    利用g . kani提出的拱?齒理論中的無腹筋梁的拱齒破壞的分界點（也就是無腹筋粱的最小抗剪承載力點） ，再結合前述理論中所提出的梁剪壓破壞和斜拉破壞的分界點，提出了梁在延性的剪壓破壞范圍內的最小抗剪承載力，並與混凝土結構設計規范gb50010 - 2002比較，結果吻合較好。
  10. The minimum shear resistance of beams in the paper is close to the one in the code for design of concrete structures " gb50010 - 2002 '. according to the actual project, the destroy of 448 kinds of beams are analyzed by computer by taking account of the effective coefficient " " of the strength of concrete confined by hoops, the relationship with the section property of beams, the critical point of the arch - rib failure transiting to the shear - compression failure which is advanced in the anti - theory, and the contribution to the beam ' s shear resistance of the concrete in the shear - compression zone

    引用箍筋約束混凝土的有效系數，利用其與梁截面特性的關系並結合理論分析中提出的梁剪壓破壞與斜壓破壞的分界點，同時考慮了剪壓區混凝土的抗剪貢獻，從工程實際出發，編程擬算了448種梁構件的破壞情況，計算結果表明，梁發生在剪壓破壞范圍內的最大抗剪承載力值比混凝土結構設計規范gb50010 - 2002值略高。
  11. Simulation on the a - magnet of 30mev linac is also done with the gpt code ; the movement picture of electron beam in a - magnet is presented ; the change of beams emittance, the compression effect of bunch length, change of energy dissipation and achromatic angle of true a - magnet are explored. this chapter mainly introduces some characteristics and properties of the main accelerate stage in 30mev linac system

    利用gpt程序對30mevlinac中的-磁鐵進行了動力學模擬，給出了電子束在-磁鐵中的運動圖像，研究了注入器輸出束流經過-磁鐵后束流發射度的變化、束團長度的壓縮效應、能散度的變化以及-磁鐵實際的消色散入射角。
  12. Not only t he self - weigh of every beam, the prestressing, the compression on the support of form scaffolding, constriction of concrete, creeping are considered when the inter nal force is calculated, but also the result of displacement and deviation of th esupport and precamber should be taken into consideration

    施工階段的內力計算不僅考慮逐段施工梁的自重，預加應力，模板支架的支點壓力，以及混凝土的收縮、徐變；同時還應考慮施工程序，施工中的支座位移、支座偏差和預拱度等的影響。
  13. Through the experimentation for the physical performance of cfpb masonry under local compression, the author has observed the deformation and failure of cfpbm. based on the mathematical statistics and regression analysis of the experimental data, the author derived a feasible and common formula for counting the cfpbm ' s local compression strength regarding the different local compression locations, analyzed stress distribution of local bearing masonry under beams end, and provided the calculating formula on effective supporting length of beam end in brick masonry. as the results of experiments demonstrate, owing to the cfpb ' s own holes " system, the beneficial effects, the bounding effect of surrounding masonry and the spread effect of force, have not developed completely

    試驗結果分析表明：由於多孔磚自身的孔洞結構，砌體內部的圍箍作用和力的擴散作用未得到充分發揮，局壓強度雖較軸心受壓強度有所提高，但仍低於同情況下實心磚的局壓強度；當有上部荷載作用時，對砌體局壓有利的懸臂卸荷作用和內拱卸荷作用均不明顯，因此在推導梁端局壓強度計算公式時，未考慮此可能存在的有利影響，計算偏安全；局壓強度提高系數公式除採用規范公式（二項式）的表達式，還用對數式進行了回歸推導，得到了一個較為普遍的公式；論文還對梁端局壓的梁端有效支承長度計算公式進行了回歸推導。
  14. During elastic - plastic stage, the wall was equaled to a rigid frame - oblique compression bar model. during failure stage, the wall was equaled to a beam - hinged frame

    彈性階段一一復合材料等效彈性板模型;彈塑性階段，一捆lj架斜壓桿模型;破壞階段一一梁鉸框架模型。
  15. With the appearance of high strength concrete high tensile steel wire and cable, the cable - stayed bridge is more and more widely used and popular. it unites three diversely bearing structure style, compression tower tension cable and bending press beam, into one bridge style

    斜拉橋是隨著高強度混凝土材料、高強鋼絲和拉索的出現才得到廣泛推廣應用的橋型，它把主塔受壓、拉索受拉及主梁受壓彎的三種不同受力的構件有機地組合在一個統一體中。
  16. Using the general finite element programming package of ansys10. 0, the study of gabled frames beam - column end - plate connections is made, considering synthetically nonlinear ( material, geometry and contact ), bolt pretension forces and ratio of axial compression stress to strength. elastic - plastic finite element analyses are carried out among 28 species of 3 series under monotonic loads, in order to discuss the influence of parameters including stiffness of end - plate, bolt diameter, friction coefficients and so on

    本文使用通用有限元軟體ansys10 . 0綜合考慮了三重非線性（材料非線性、幾何非線性以及狀態非線性）的影響，同時考慮了螺栓預拉力的影響，對考慮端板厚度、端板加勁肋的設置、螺栓直徑、摩擦系數等參數不同的3個系列（端板系列，螺栓直徑系列，摩擦系數系列） 28個試件進行了有限元數值模擬，對連接節點的性能進行了分析研究。
  17. ( 2 ) based on deterioration model of owerage bond stress of beam reinforcement accounting for effect of axial compression ration and number of displacement loops, and stress - strain relationship of the concrete in the joint core accounting for effects of both softening and confinement, the modified compression field theory was employed to simulate behavior of the joint core under loading reversals. analysis by means of the program jap on the tested specimens in this paper and those obtained from other researchers produced consistent results

    根據本文建立的考慮軸壓比和位移循環次數影響的梁筋平均粘結應力退化模型和考慮軟化效應、約束效應的核心區混凝土應力應變關系，通過在試驗中得出的節點核心區混凝土、箍筋、節點正面、背面柱筋在反復荷載下的受力特點，利用斜壓場理論模擬節點核心區在反復受力過程中的受力狀態。
  18. The main achievements were summarized in detail as follows : ( 1 ) the cfdst tubular beams, columns and beam - columns with chs outer steel tubes were tested systematically. the main experimental parameters were tube diameter - to - thickness ratio, hollow section ratio, eccentricity and slenderness ratio. ( 2 ) load - deformation relationship curves of cfdst subjected to compression and bending were analyzed by finite element method and fiber element method

    本文具體進行了以下幾個方面的工作: （ 1 ）分別以徑厚比、空心率、長細比、偏心距等為主要變化參數，較系統地進行了軸壓、純彎和壓彎構件在單調加載下的試驗研究。
  19. The conclusions are list as follows : ( 1 ) the mechanical properties of different parts of the bridge are as follows : arch is under the combined action of compression and bend ; open spandrel beam is under the combined action of tension and bend ; close spandrel beam is under the combined action of compression ( or tension ) and bend, but the axis force is small

    本文得出的結論如下： （ 1 ）空腹式剛架拱橋的受力兼具梁和拱的特點。結構各部位的受力特性如下：斜腿為壓彎作用；空腹段梁體為拉彎作用；中跨實腹段梁體為壓彎作用或拉彎作用，但軸向力較小，受力更接近純彎構件。
  20. The contents include as follows : the influencing factors of the displacement ductility factor of the unbonded partially prestressed concrete frame structures, such as stirrup reinforcement characteristic value, nominal shear span ratio, axial compression ratio, the appearing order of plastic hinges and partial prestressing ralio ( ppr ) are discussed. the formula of displacement ductility factor of the unbonded partially prestressed concrete frame structures is suggested by regression analysis. with regard to the aseismic design and the request of ductility and energy dissipation, the restriction of the flat - beam / column sectional size and aseismic reinforced design are discussed

    本文主要包括以下內容：討論了配箍特徵值、名義剪跨比、軸壓比、塑性鉸出現順序、預應力度等因素對無粘結部分預應力混凝土框架位移延性系數的影響，回歸了考慮影響因素的位移延性系數計算公式；對無粘結部分預應力混凝土扁梁框架結構，闡述了抗震設計對扁梁、柱截面尺寸的要求與限制；對滿足延性和耗能要求的無粘結部分預應力混凝土扁梁控制截面抗震配筋進行了探討；通過對無粘結部分預應力混凝土扁梁梁端的受力分析，改進了以往扁梁梁端扭矩設計值計算公式。
分享友人
分享到 Line

分享到臉書