compression temperature 中文意思是什麼

compression temperature 解釋
壓縮溫度
  • compression : n. 1. 壓縮；壓緊；濃縮，緊縮。2. 加壓；壓抑。3. （表現的）簡練。4. 應壓試驗。
  • temperature : n. 1. 溫度，氣溫。2. 體溫。3. 〈口語〉發燒，高燒。
  1. Metallic materials - compression testing at ambient temperature

    金屬材料室溫壓縮試驗方法
  2. This company strictly according to the iso9001 - 2000 management system request, utilizes the advanced bamboo processing complete set of equipments, uses the advanced domestic and foreign productions craft, the raw material is selected from the high quality natural bamboo, through steamed and boiled in the high temperature, got rid of the sugar and the degrease, carbonized, past the high temperature and thermo - compression

    廠區一角本公司嚴格按照iso9001 - 2000管理體系要求，運用先進的竹加工成套設備，採用國內外先進生產工藝，選用優質天然楠竹為原料，經過高溫蒸煮脫糖脫脂碳化高溫熱壓等數十道工藝，生產防霉防蛀阻燃的「湘君」牌綠色環保型系列產品。
  3. The dishing ring seals belong the end face sealing parts, and act as sealing by some axial compression. because of different distribution of internal pressure and temperature, the friction inside the end - face is also different at all area

    碟形密封圈屬于端面密封元件，依靠一定的軸向壓縮量進行密封，由於端面內壓力分佈、溫度分佈不均，端面內的摩擦狀況也不是處處相同。
  4. Rubber vulcanized. determination of temperature rise and resistance to fatigue in compression flexometer testing

    硫化橡膠.用壓力撓度計試驗時對溫升和抗疲勞性能的測定
  5. Experimental studies on s1a - 02 gas turbine with water injection into compressor interstage / inlet as well as that on turbocharger self - loop test rig with inlet water injection are introduced. test results are in good accordance with simulation results, wet compression can lower compression work and increase engine power output so engine performance is enhanced, if engine power output is not changed, efficiencies of compressor and this engine become higher and turbine inlet temperature and fuel consumption become lower and if keeping t4 the same as that before wet compression is used, efficiencies become furthermore higher and engine power output increases greatly

    實驗結果和計算結果同樣表明：濕壓縮減少了壓氣機所消耗的壓縮功，增加了燃氣輪機的輸出功率，提高了燃氣輪機性能，如果保持發動機輸出功率恆定，濕壓縮可以提高壓氣機和整個燃氣輪機機組的效率，與此同時，渦輪進口溫度t _ 3 ~ *和燃油消耗率下降；如果保持渦輪排氣溫度t _ 4 ~ *恆定，壓氣機和燃氣輪機機組效率進一步提高，燃氣輪機輸出功率增加。
  6. Preparation and fracture behavior under monaxial compression at room temperature of zr57nb5cu15. 4ni12. 6al10 bulk amorphous alloy

    10大塊非晶態合金的制備及其室溫單軸壓縮斷裂行為
  7. The following results were found, i. e., the water ratio affects obviously the acoustic wave velocity of rock sample ; the wave velocity is higher in saturated rock samples than in unsaturated ones ; and it decreases gradually with the strain of samples during uniaxial compression ; and also with the lengthening holding time at 160 ; when heating the samples the acoustic wave velocity increases slightly in initial stage and comes to the peak value at 60, then decreases gradually with increasing temperature ; meantime, there is a certain temperature effect on rock samples size

    實驗發現含水率對波速影響比較大，飽和巖樣的聲波傳播速度高於不飽和巖樣的聲波傳播速度；人工預制裂紋對聲波傳播速度影響不大；單軸壓縮條件下，聲波傳播速度隨應變增加逐漸降低；在同一溫度（ 160 ）下，波速隨保溫時間的增加而逐漸降低；在對巖樣逐漸加熱情況下，初始加熱階段波速略有升高，當溫度達到60時，巖樣波速達到峰值，之後隨著溫度繼續升高其波速逐漸下降；波速隨溫度變化具有一定的尺寸效應。
  8. It is appropriate for measuring end temperature of bearing liner or other works, e. g., push bearing liner of steamer, supporting bearing liner or push bearing liner of electromotor main axis, bearing liner of coal pulverizer, bearing liner of high efficient feed water pump, bearing liner of compression machine and kinds of other objects inpetrochemical plant

    適用於測量軸瓦或其它機件的端面溫度，如：汽輪機推力軸瓦，電機主軸支持瓦推力瓦，磨煤機大瓦和高效給水泵軸瓦石油化工廠壓縮機軸瓦和各種機件物體的表面測量。
  9. Adiabatic compression temperature

    絕熱壓縮溫度
  10. A new calculation method for optimizing diesel engine performance, called nonlinear regression - mess method, is put forward. in this paper, 25 groups of simulated values are calculated from the diesel engine working model, specific fuel consumption, peak pressure, rate of pressure rise, nox and peak temperature are fitted into explicit function about compression ratio and fuel injection advance angle

    本文利用柴油機工作過程模型，得出25組模擬計算數據，利用非線性回歸將油耗、最大爆發壓力、壓力升高率、 no _ x濃度及最高燃燒溫度擬合成壓縮比和噴油提前角的顯函數，並用網格法進行優化，用c語言編制了優化計算程序，得出最佳的壓縮比和噴油提前角，使其優化匹配。
  11. The planeness and integrality of the flier - plate were ensured effectively by exerting restrictive pressure, controlling heating and cooling rate, lowering welding temperature or reducing welding time as much as possible, etc. theoretical model of creating quasi - isentropic compression via 93w - ofc - tc4 - a1 - mb2 system flier - plate with graded wave impedance was established, and numerical simulation of the impact process was then carried out

    採取施加外部機械力、控制升降溫速率以及盡量降低焊接溫度或減少焊接時間（防止脆性金屬間化合物的過度增長）等措施，確保了焊接接頭的平整性和界面結構的完整性。建立起梯度飛片擊靶的理論模型，對93w - ofc - tc _ 4 - al - mb _ 2系波阻抗梯度飛片的擊靶過程進行了數值模擬計算。
  12. As shocked porous iron has a higher temperature than solid iron, we can investigate eos of iron at higher temperatures by shock compression of porous iron samples

    本文利用多孔鐵在沖擊壓縮過程中比密實鐵具有更高溫升的特性，對多孔鐵的物態方程進行了比較深入的研究。
  13. The tensile and compression experiment on bulk nanocrystalline ag prepared by igc method was carried on mt810 with different grain sizes and zwick 10tn2s machine at different strain rates under normal temperature respectively. the stain rate sensitivity m was found to be 0. 025, which was extremely lower than the ordinary values. also the work hardening exponent is very low

    本文從用惰性氣體蒸發冷凝和真空原位壓結法（ igc ）制備得到的直徑80mm ，厚度7 . 6mm的大尺寸納米晶金屬ag樣品上切割得到符合力學實驗要求的拉伸和壓縮試樣，在mts810和zwick精密力學測試機上分別精確測定了拉伸和壓縮應力?應變曲線與晶粒尺寸和應變速率的關系。
  14. This program can work out some changes made by the operation of wet compression, such as the maximal mass of water spray, the temperature in the outlet of supercharger, and the consumed energy by the supercharger. in addition, this thesis gives the definition of efficiency of wet compression when the entropy of compressed air keeps constant, and it can be the standard for the study of wet compression

    本文首先對增壓柴油機濕壓縮研究的主要部分? ?壓氣機，建立濕壓縮的數學模型，從理論上分析濕壓縮的最大噴水量，壓氣機出口溫度，壓氣機耗功等變化情況，並給出了等熵濕壓縮的定義，為濕壓縮研究建立了比較標準。
  15. For overterm service of unit equipment in thermal plant, taking high temperature compression part ( steam pipe ) for example, the paper introduced a three grade appraisal method and calculated the residual life of high temperature compression part using fixed asset linear method, establised a economic life mathematical mode, finally gave out a general economy appraisal for high temperature compression part with a calculation example

    針對火力發電廠機組設備的超期服役，以高溫承壓部件蒸汽管道為例，以其運行工況為基礎，結合材質狀況，逐步實行三級評定，計算高溫承壓部件的剩餘壽命，利用固定資產線性折舊法對設備進行折舊計算，同時建立經濟壽命的數字模型，綜合評定高溫承壓部件的經濟性，並列舉了算例。
  16. Royco 889 is a synthetic - based lubricant formulated for use in gas compression applications that require wide operating temperature ranges and minimun interaction between the lubricant and the process gas

    Royco 889是一種合成型的潤滑油，專門設計用於需要寬工作溫度范圍且能最大程度上減少潤滑油與氣體反應的氣體壓縮過程。
  17. Five aspects, such as the highest temperature in the middle of block, maximum horizontal stress, average stresses of any sections, stress changing process of typical points, and stress changing range between tension and compression, are discussed in detail

    從各塊體中部最高溫度、最大水平約束應力、斷面平均水平約束應力、典型點應力發展過程、正反向應力變幅等5個方面，比較系統地闡述了大體積混凝土通倉澆築問題。
  18. Through analyzing the effect of temperature and nitrogen on crude oil viscosity the influences of different nitrogen injection volume and injection modes on steam displacement are contrasted, the mechanism of nitrogen - assisted steam stimulation is clarified, which includes : heat carrying capacity is raised, the saturation of remaining oil is reduced after nitrogen - assisted injection is made ; crude oil flow is enhanced because of nitrogen compression and dispersion and the change of oil flow shape ; water back - production rate is improved by expanding the steam sweep volume and compensating in - situ energy ; steam distillation effect is enhanced

    通過分析溫度、氮氣對原油粘度的影響，對比不同注氮量、不同注入方式等對蒸汽驅油效果的影響，弄清了氮氣輔助蒸汽增產的機理主要表現在：氮氣輔助后增加攜熱能力，降低殘余油飽和度，氮氣的壓縮膨脹作用分散和改變了原油流動形態，增強了原油流動性；擴大蒸汽的波及體積，補充地層能量，提高回採水率，強化蒸汽蒸餾效應。
  19. The experimental result of superplastic compression indicates that strain rate has intensive effect on flow stress of ti - 1023 alloy and the effect of temperature is related with strain rate

    超塑性壓縮實驗結果表明，應變速率對ti - 1023合金流動應力具有強烈的影響，溫度對流動應力的影響程度與應變速率大小有關。
  20. By considering the effect of different binders, basicity, reduction temperature and time on the compression strength and dezinc degree after reducing, find out the best scheme a1b3c3d3 and get the metallic pellets with higher compression strength and dezinc degree

    通過研究不同粘結劑、堿度、還原溫度和還原時間對熟球抗壓強度、脫鋅率的影響，找出最佳試驗方案為a1b3c3d3 ，得到脫鋅率和抗壓強度較高的金屬化球團。
分享友人
分享到 Line

分享到臉書