constant-frequency supply 中文意思是什麼
constant-frequency supply
解釋
恆頻供電-
Through analyzing the figure of energy wasting of pump, the quality in pipes is direct proportion of the speed of pump if the speed of pump is reduced. the power of electromotor fell the cube of the speed of pump. so the energy wasting of constant pressure water supply based on variable frequency speed regulating technology is envident less than the traditional mode is used throttle to supply water
分析水泵工況的能耗比較圖，可以看出利用變頻調速實現恆壓供水，當轉速降低時，流量與轉速成正比，功率以轉速的三次方下降，與傳統供水方式中用閥門節流方式相比，在一定程度上可以減少能量損耗，能夠明顯節能。 -
Transitional feature of the arc and metal droplet in the welding process with steam shielded arc is investigated by means of analysing the waveforms of welding voltage and current under different welding regimes and it is found that there are two types of arc process behavor ? " arc starting - arc blowing out - short - circuiting " and " arc - starting - short - circuiting ". under the condition of constant diameter of welding wire and its feeding speed, the arc process behavor can be changed by adjusting the inductance of welding circuit as well as the voltage of power supply. if arc process behaves as alternative process of " arc starting - arc blowing out - short - circuiting " with minimum time duration of arc blowing out and maximum frequency of short - circuit transition, the welding process will be stable with less spatter and smooth weld bead
通過分析不同焊接規范下的焊接電壓和電流的波形.研究了水蒸氣保護下電弧及熔滴過渡的特點，發現其電弧過程行為有「燃弧?熄弧?短路」和「燃弧?短路」兩種形式.在焊絲直徑和送絲速度一定的情況下，通過調節焊接迴路中的電感量和電源電壓，可以改變電弧的過程行為形式.若電弧過程呈「燃弧?熄弧?短路」交替進行，並且熄弧時間最短時，短路過渡頻率最高，在這種情況下，飛濺小，焊道成型好，焊接過程穩定 -
The variable polarity power supply circuit uses two stages full - bridge inverter, the former inverter is regarded as a constant - current source with fast dynamic response, and supplys energy for the second one, and the latter one is to produce variable polarity current excellently, and low - frequency pulse current by variable polarity power supply is used to reduce input energy and control the shape of weld bead while welding. a series of high - frequency pulse current is superposed on direct - current - electrode - negative ( dcen ) current through the high - frequency pulse power supply, which is used to compress the arc and improve process of crystallization
其中變極性電源採用二次全橋逆變結構，一次逆變提供快速的響應速率並給二次逆變提供能量，二次逆變提供良好的變極性性能，使輸出能量最優化，並用其低頻電流特性減小電弧線能量，控制焊縫成形;高頻脈沖電源提供的高頻電流疊加在反極性電流dcen上，利用電流的高頻特性壓縮電弧，改善焊縫金屬結晶過程。 -
The hardware circuit design include : industrial control computer configuration, selection of industrial control board type, design of the power supply and monitoring interface circuit, design of signal processing interface circuit ( the constant current source circuit, the time base signal processing circuit, the processing circuit for the signal to be measured ), design of panel control circuit, design of the system self - checking circuit, and etc. the program flow hart include : main program flow chart, system boot - strap self - checking program flow chart, manual static testing program flow chart, semiautomatic static testing program flow chart, automatic static testing program flow chart, dynamic testing program flow chart, transient testing program flow chart, source voltage and current monitor program flow chart, investigate function testing program flow chart, and etc. the measure system offers six working power supplies, the signal of time base, the signal of constant current source, sine wave signal and step to leap signal, and measures the frequency of the output pulse signal of the wide range pulse convert circuit accurately under three kinds of different test state ( static form, dynamic form and transient form )
硬體電路設計包括：工控機配置、工控板卡選型、產品電源及監控介面電路設計、信號處理介面電路（恆流源電路、時基信號處理電路、被測信號處理電路）設計、面板控制電路設計、系統自檢電路設計等。程序流程圖包括：主程序流程圖、系統開機自檢程序流程圖、手動靜態測試程序流程圖、半自動靜態測試程序流程圖、自動靜態測試程序流程圖、動態測試程序流程圖、暫態測試程序流程圖、電源電壓和電流監控程序流程圖、研究功能測試程序流程圖等。測試系統提供六路工作電源、時基信號、恆流源信號、正弦波信號和階躍信號，並對三種不同測試狀態（靜態、動態、暫態）下大量程脈沖變換電路輸出脈沖信號的頻率進行精確測量。 -
Aeronautical static inverter ( asi ) is a kind of static converting device, which converts the dc ( 27v / 270v ) in the main power of aircraft into ac of constant - voltage and constant frequency by means of power semiconductor devices. with the development of the aircraft, all the electric equipment on the plane requires the power supply system with better performance
航空靜止變流器（ asi ? aeronauticalstaticinverter ）是航空電源系統的二次電源，其作用是將飛機主電源直流電27v或270vdc變換成恆壓恆頻單相115v 400hz ，單相36v 400hz ，三相115v 200v ，或三相36v交流電，供飛機上負載使用。 -
Constant stator magnetic linkage control frequency converter includes power devices utilizing igbt, drive circuit using three - phase drive ic with multiple protection functions. pwm signal formation circuit in the way of voltage space vector control and realized with pld ( programmable logic device ) devices and compensation for the influence of supply voltage variation and stator resistance voltage drop
其中，恆定子磁鏈控制變頻器的設計中主電路採用功率器件igbt ；驅動電路採用三相多功能集成驅動晶元； pwm脈寬調制信號產生電路採用電壓空間矢量控制方式，由pld器件實現；對電源電壓變化及電阻壓降造成的影響進行了補償。 -
A frequency conversion timing control system for constant pressure water supply based on lonworks field bus
現場總線的恆壓供水變頻調速系統 -
On the basis of analyzing status in quo of the waterworks in our country, this paper designs a suit of constant pressure water supply automatic control system by using variable frequency speed - regulating technology based on plc
本論文結合我國中小城市供水廠的現狀，設計了一套基於plc的變頻調速恆壓自動控制供水系統。 -
Kv 0. 7 a high voltage variable frequency constant current capacitor charging power supply
高壓變頻恆流充電電源35 -
In chapter 3, according to the requirements of high voltage power supply used for charging capacitors with constant current, the series resonant converter ( src ) was chosen as the main circuit frame. the dynamic process of src was discussed by using mathematical analyses and numeric simulation to study the operational characteristics, the effects of parameters of resonant circuit on them and the relationship between switching frequency and out put power, which provided the bases of designing the power supply
第三章中根據高壓電容恆流充電電源的運行特點，選擇了串聯負載諧振變換器作為主電路結構形式，並對其動態過程進行了數學分析及數值模擬，討論了該電路的運行特點、諧振迴路參數對運行特性的影響以及開關工作頻率與功率輸出的關系，為電源的設計提供了依據。 -
The main working contents of this paper is following : 1 according to the theory of electromagnetic induction law, a new radio induction system is proposed based on the traditional radio induction technology, analyzed on its signal transmission character and its frequency spectrum character. the channel composed of the new radio induction system is compared with the parameter - constant channel and the parameter - changing channel. the application of the new radio induction system is studied in converter supply
本文的主要工作內容如下： 1在現有的無線感應技術基礎上，基於電磁感應理論，提出了新型無線感應系統，分析了新型無線感應系統的信號傳輸特性，分析了新型無線感應系統的頻譜特性，把新型無線感應系統組成的通道和恆參通道、變參通道進行了比較，研究了新型無線感應系統在變流器供電中的應用。 -
Application of variable frequency constant pressure water supply equipment in lage - scale pumping station
變頻恆壓供水設備在大型泵站的應用 -
Energy consumption analysis on constant - pressure variable - frequency water supply and variable - pressure variable - frequency water supply
變頻調速恆壓與變壓供水的能耗分析 -
The mixed control chip sg3525a combined with hardware pi controller generates the high - frequency pwm pulse for the first inverter. the digital control block tms320lf2407a mainly provides current preset for constant - current source through the outer filter, pwm pulse for the second inverter and drive signal for the high - frequency pulse power supply
其中變極性電源的一次逆變pwm信號由pwm發生晶元sg3525a ，配以外部硬體電路pi調節器產生;一次逆變閉環控制迴路的電流給定（配以外部濾波） 、二次逆變pwm驅動以及高頻脈沖電源的控制則由tms320lf2407a數字控制器實現。
分享友人