converter iron 中文意思是什麼
converter iron
解釋
轉爐用生鐵-
The converter is tipped on to its side and the charge of molten iron is poured into the top.
轉爐向一邊傾斜，熔鐵從頂部倒進去。 -
Application of iron - bearing material for slag - making in converter practice
含鐵渣料在轉爐冶煉中的應用 -
Medium plate plant of chongqing iron & steel has reconstructed technically the original two stand rolling mills ( roughing mill and finishing mill ) and changed dc drive system into ac frequency converter drive system
重慶鋼鐵集團公司中板廠對兩臺主軋機（粗軋機和精軋機）驅動系統進行了技術改造，將原來的直流驅動系統全部改造成變頻調速驅動系統。 -
The results of experiments taken in handan iron & steel co. ltd show that adoption of lining protection by slag splashing can drastically extend furnace campaign, reduce consumption of refractory material and improve availability of converter, thus achieving remarkable economical benefits. it is worthy of being extensively applied
邯鋼的濺渣護爐試驗結果表明，採用該工藝能大幅度提高爐齡，降低耐火材料消耗，提高轉爐作業率，綜合經濟效益可觀，值得推廣應用。 -
In order to keep the normal bath temperature and slag forming condition, the charge of pig iron should not be exceeded 10 % on middle and small converter
中小型轉爐內生鐵塊的加入量不應超過10 % ，使轉爐吹煉過程中保持正常的熔池升溫和成渣狀況。 -
In chapter 2, the nonlinear feature of iron core of transformer in switching power supply was studied. according to the characteristics of switching power supply, the topology structure of resonant converter was selected. the characteristics of out put voltage and current vs. frequency for the three kinds of resonant converter were analyzed and compared
在第二章中，研究了高壓開關電源中高壓變壓器的非線性特性，選擇了諧振變換器作為高壓大功率開關電源的電路拓撲結構，並對三種形式的諧振變換器的電壓及電流頻率特性進行了分析比較。 -
Automation control system for converter of benxi iron and steel co
本鋼轉爐自動化控制系統 -
Excessive pig iron is usually charged in converter in order to increase steel output at middle and small steel plants
摘要中小轉爐鋼廠為了增加鋼產量，往轉爐內過量加入生鐵塊。 -
The thin slab continuous casting and continuous rolling technology that was adopted by zhugang is an important technological revolution after the development of oxygen converter and continuous casting in the world iron and steel making industry field. in comparison to the conventional hot strip and sheet rolling technology the new technology has advantages such as saving investment cost, increasing finish product yield, decreasing production cost and shorting production cycle in large scale
珠鋼選用的薄板坯連鑄連軋工藝是世界鋼鐵工業領域中，繼氧氣轉爐煉鋼、連續鑄鋼之後的重大技術革命，與傳統的熱軋板材生產工藝相比，它具有節約投資、提高成材率、降低生產成本、大幅度縮短生產周期等優勢 -
Finally, after calculating iron loss and copper loss with the magnetic field analysis, use it as a heat source, and conduct a non - stationary analysis independently with the three dimensional thermal analysis which concentrates on the effect of the heat transfer coefficient on the temperature rise. in this paper, a bipolar switched reluctance machine system model is also established with an h bridge converter as its power circuit topology
另外，本文還建立了雙極型sr電機系統模型，採用了h橋式功率主電路，詳細分析了其工作原理，並在磁場、損耗等方面與採用不對稱半橋變換器的傳統單極型sr電機系統進行了對比。 -
Tianjin iron steel company ltd., tianjin, china, decided to convert their two existing 300 tpd coal dust fired maerz lime shaft kilns to converter gas firing and placed the corresponding order with maerz
現有的麥爾茲窯是圓筒形的，其每個窯筒的燃燒區截面積為7 . 1 m2 。 -
The application of high power electronic converter technology in iron and steel industry
大功率電力電子變流技術在鋼鐵工業中的應用
分享友人