cooling water valve 中文意思是什麼
cooling water valve
解釋
冷卻水閥-
This watts / flippen float valve product guide features high quality, reliable control assemblies and components that provide make up water for pressure washers, cooling towers, heat transfer units, cattle watering tanks, refrigeration units, and for many other applications where float valves are required
這種美國瓦茨/ flippen浮球閥的特點在於其優質、控制可靠的部件，為壓力清洗裝置，冷卻塔，熱傳送裝置，牲畜水塔，冷凍裝置，以及其他各種要求浮球閥的應用提供補給水。 -
The results showed that the range of target finishing temperature can be provided and kept on in an energy - saving manner with lower frequency of spray nozzle opening if opening reversely but closing forwardly the cooling valve for inter - stand spray during water cooling
對兩種截然不同的機架間噴水冷卻閥門開啟邏輯做了計算分析，結果表明，逆向開啟機架間噴水冷卻閥門，順向關閉閥門，能以較少的噴嘴開啟數達到終軋溫度目標范圍，並且可以節約能耗。 -
The results show that, when the compressor continuously runs, the stability of the test bed after using manual valve is better than that of using thermal valve, and it is little affected by the kinds of valves for adjusting cooling water ; and that, when the compressor intermittently runs, the operation stability would be obtained if pneumatic valve is used to adjust cooling water, especially at low speed
結果表明，壓縮機連續運行時，製冷劑採用手動閥調節后工況的穩定性明顯好於採用熱力膨脹閥時的情況，此時調節冷卻水量用的電動調節閥和氣動調節閥對工況穩定性影響相差無幾；間歇運行時，無論是熱力膨脹閥還是手動閥，即便壓縮機通電時間最長，仍達不到設定工況，特別是低速的斷續尤為明顯，而使用氣動閥就能很好地解決這一問題。 -
It specifies the process of the design, simulation and experiment of liquid cooling system. main contents of the thesis are as follows : description of the present usage of liquid cooling system, presentation of a new type of liquid cooling system and description of its work principles ; design of the liquid cooling system, which mainly deals with the design and collating calculating of serpentine condenser and heat exchangers adopted in this system. meanwhile, the model chosen calculating of compressor 、 thermal expansion valve 、 plate evaporator 、 water pump and the like equipment used in the system are also carried out
本文的主要內容如下:對液冷源使用現狀進行了描述，提出了一種新型液冷源系統並對其工作原理進行了闡述;對系統進行了設計，主要對系統中所採用的管帶式冷凝器和水側空/液換熱器進行了設計和校核計算，同時對系統中所用到的壓縮機、熱力膨脹閥、板式蒸發器、水泵等配套設備進行了選型計算;分別對製冷系統和冷卻液循環系統進行了數學建模。 -
Through theoretical analysis and real machine demonstration, the control measure of " ensuring stable status of the specific chiller by utilizing plc technology and by controlling the operating pressure of the water chiller of the cooling system through electric 3 - way regulating valve " was researched
摘要通過理論分析和實機驗證，研究了「利用plc控制技術通過電動三通調節閥控制製冷壓縮機的冷凝壓力，進而保證冷水機組的狀態穩定」的控制措施。 -
If, after pressing reset button, valve does not stay open allowing gas to flow to the burner, insufficient cooling of the water is the probable cause
如果按下重置按鈕后，閥門不能夠停留在開啟的位置讓燃氣流向燃燒頭，可能就是因為水溫降得還不夠低造成的。
分享友人