coupling capacitance 中文意思是什麼
coupling capacitance
解釋
耦合電容- coupling : n. 聯結；交尾；【機械工程】管箍；聯結器；軸接；（火車的）車鉤，【電學】耦合。
- capacitance : n. 【電學】電容；電容器。
-
Experimental results show that the bistable of tuned substrate self - bias was determined by discharge gas pressure, discharge power and tuning circuit parameters etc. the bistable exists is because of there is capacitive coupling in icp system and sheath capacitance is nonlinear
實驗結果表明這種跳變回滯現象與等離子體的放電氣壓、射頻功率以及調諧外電路的參數等多種因素密切相聯系。而產生跳變回滯現象的原因是icp中存在容性耦合以及鞘層電容具有非線性特性。 -
The basic principles still apply : ground impedance must be as low as possible, high level and low level signals must be separated so that they do not interfere with each other, and capacitance and mutual inductance coupling must be avoided
前文提到的原理仍然適用：地線阻抗要盡量小，大功率信號和微弱信號要分開布置以避免串擾，一定要避免電容性耦合和電場耦合。 -
Traditional static crosstalk identification methods identify crosstalk targets only using coupling capacitance and noise amplitude information, which lead to the pessimistic results and induce a long time to ic design convergence
摘要傳統的靜態串擾噪聲識別演算法只驗證耦合電容和噪聲幅值信息，沒有考慮噪聲寬度對電路邏輯功能的影響，所以給出的結果過于保守，導致設計收斂的時間被延長。 -
The main job of this research is : ( 1 ) analyze the operation situation of power system during faults ; pay attention to the traveling wave on the three - phase transmission line ; study the equation of voltage on three - phase transmission line with impedance capacitance coupling between phases ; contact the voltage on any point with the fault voltage, study the singularity of the voltage signal in fault point, and make it to be the base of the new fault detection method ; ( 2 ) apply the singularity detection theory based on wavelet analysis to the power system faults detection, give a complementary criterion to current fault detection criterion, study how to select the basic wavelet, how to filter noise, how to detect the singular point or fault point, and finally give a total solution. the simulations prove it to be a quick, correct and effective fault detection method
本文的主要工作有： （ 1 ）分析電力系統在發生故障時的運行狀態，尤其對三相傳輸線上的故障行波進行了分析和研究，推導了考慮相間耦合的三相傳輸線電壓方程，並將傳輸線上任一點的電壓與故障點電壓建立起聯系，得出了傳輸線上電壓信號在故障點處的奇異性，並以此作為構造新的故障檢測演算法的理論基礎； （ 2 ）將基於小波變換的信號奇異性檢測理論運用於電力系統故障檢測中，針對目前相關研究的不足，提出了電力系統故障檢測判據的補充判據，通過對基本小波的選擇、除噪措施、信號奇異點也即故障點的檢測方法所作的分析，給出了一個可行的解決方案；模擬研究表明：這是一個快速、準確、有效的故障檢測演算法。 -
An algorithm to resolve the coupling effect problem is proposed during the cross point assignment ( cpa ) stage. in the algorithm, the priority queue concept and the rip - up and reroute strategy are combined to control crosstalk noise caused by interconnect coupling capacitance. first, the nets are arranged into different priority queues according to their weighted sum of their length and criticality. then, the cpa problem for one queue of nets is translated into a linear assignment problem. after the assignment of one queue of nets, a post - cpa checking routine is performed to check and rip up the net pairs which violate the crosstalk noise constraint and then push them into the next queue to be reassigned. the algorithm is tested by a set of bench mark examples, and the experimental results are promising
提出了一種在過點分配階段解決噪聲耦合效應問題的演算法.該演算法採用優先隊列同拆線重布策略相結合的方法，控制由互連線耦合電容引起的串擾噪聲.演算法中，首先按照線長和約束限制，將線網劃分到若干個優先隊列中.然後，將每個優先隊列的過點分配問題轉換為線性分配問題.在完成一個線網隊列的分配后，通過過點分配后處理過程檢查串擾約束滿足情況，對違反約束的線網對進行拆除，放入后續線網隊列進行重新分配.實驗數據表明，該演算法能夠取得好的效果 -
Abstract : an algorithm to resolve the coupling effect problem is proposed during the cross point assignment ( cpa ) stage. in the algorithm, the priority queue concept and the rip - up and reroute strategy are combined to control crosstalk noise caused by interconnect coupling capacitance. first, the nets are arranged into different priority queues according to their weighted sum of their length and criticality. then, the cpa problem for one queue of nets is translated into a linear assignment problem. after the assignment of one queue of nets, a post - cpa checking routine is performed to check and rip up the net pairs which violate the crosstalk noise constraint and then push them into the next queue to be reassigned. the algorithm is tested by a set of bench mark examples, and the experimental results are promising
文摘:提出了一種在過點分配階段解決噪聲耦合效應問題的演算法.該演算法採用優先隊列同拆線重布策略相結合的方法，控制由互連線耦合電容引起的串擾噪聲.演算法中，首先按照線長和約束限制，將線網劃分到若干個優先隊列中.然後，將每個優先隊列的過點分配問題轉換為線性分配問題.在完成一個線網隊列的分配后，通過過點分配后處理過程檢查串擾約束滿足情況，對違反約束的線網對進行拆除，放入后續線網隊列進行重新分配.實驗數據表明，該演算法能夠取得好的效果 -
Design the good - working signal processing circuit of the sensor, including the signal collecting circuit of three output polars the coupling circuit using capacitance and resistance the alternating amplify processing circuit and the stabilization voltage supply circuit
設計了性能良好的信號處理電路（包括銻化銦磁阻三端輸出型信號採集電路、阻容耦合型交流濾波放大電路和穩壓電源電路三個部分） 。 -
Also, we select the signal collecting circuit of three output polars, the coupling circuit using capacitance and resistance, the alternating amplify processing circuit, the positive feedback retardation comparsion, the driving circuit of output current and the stabilization voltage supply circuit
選擇了insb磁阻三端輸出型信號採集電路，阻容耦合型交流放大電路，正反饋遲滯型電壓比較器和大電流推挽驅動電路及穩壓電源電路。 -
A few kinds of signal separate measures, double caner frequency automatc switch function and relay function are taken into account on the design of wfplc - ml iniddle - voltage distribution line carrier modem. coupling equipment is designed with the filter and capacitance fitted togethel in this papef, it is also advanced an scheme about caner signal spanning the distribution line break. the equipment system has been finished and put into use, which has better result. the feasibly and necessity of the studying of this problem are posed
Wfplc3510中壓配電載波系統利用10kv的架空線或電纜，將主控斷發出的命令信息轉換為載波信號通過三相耦合器耦合到電力傳輸線上，在被控端利用單相耦合器耦合到載波信號后轉換為介面信號發送給被控單元，被控單元亦可將返回數據通過單相耦合發送載波信號到主控端，實現信息的雙向傳遞。 -
In the course of our static crosstalk noise identification, the noise width along with coupling capacitance and noise amplitude are used to identify static crosstalk noise targets, which overcomes the conservative defect of previous methods
文章在傳統演算法的基礎上增加了噪聲寬度這一識別指標，克服了以往演算法結果過于保守的缺點。 -
Discussion the design of the process flow and device structure of comb capacitance mode micro shear stress sensor in details, selecting suitable thin film material. finite element analysis the structure and fluid coupling of comb capacitance device was performed by ansys software
然後利用有限元分析軟體ansys對梳齒電容式微型剪應力傳感器的質量塊模型進行結構和流體耦合分析，得到梳齒質量塊結構的應力分佈和位移分佈雲圖。
分享友人