creep strain 中文意思是什麼
creep strain
解釋
蠕變變形-
The calculation modes of the coefficient of shrinkage and creep of the bulgy core concrete in steel tube are discussed. based on a few reasonable hypotheses and the stress - strain relation of concrete acquired by the " adjusting valid modulus depending on load time " method, a compact formula is reasoned out, which is applied to calculate the equivalent elastic modulus of the bulgy core concrete considering the affection of shrinkage and creep. so, the analysis of the affection on cfst arch bridge by shrinkage and creep can be progressed by pole - girder fem, further more, the analysis precision is quite high
本文還對核心膨脹混凝土特殊的收縮、徐變系數計算模式展開了探討，在合理的假設前提下，採用「齡期調整的有效模量法」得到的混凝土的本構關系，推導出鋼管內核心混凝土在考慮徐變影響后的等效彈性模量計算公式，並以此為基礎採用桿系有限元方法來對鋼管混凝土拱橋進行較高精度的收縮徐變分析。 -
This result has practical significance. in this paper ' s theoretical section, base on current shrinkage and creep calculational methods, analysis to the experiment project and tall building structure examples were made, and then the influence of shrinkage and creep to structure stress was put into discussion ; moreover, an fea program was compi led to calculate shrinkage and creep strain considering construction process, and through a tall building instance, the influence to tall frame structure stress was analyzed
本文的理論部分在現有收縮徐變計算方法的基礎上對本試驗工程和高層建築結構進行了算例分析，通過與彈性計算值的對比，討論了收縮徐變對結構內力的影響，以及計算收縮徐變時是否考慮鋼筋和施工過程對結果的影響；本文還編制了考慮施工過程收縮徐變的有限元程序，並進行了算例分析。 -
Creep analysis methods of high - rise buildings and large span buildings can only refer to creep coefficient method in bridge engineering or the method of degree of creep in hydraulic construction engineering under the present experiment conditions. in this paper, the incremental expressions of concrete creep and shrinkage strain when the initial computational age is not the same as the loading age are derived and corrected from the concept of concrete creep coefficient and the mean value theorem of integral and the principle of superposition. the differences of efficiency and accuracy of creep analysis between the finite element method with creep coefficient and the initial stress method with degree of creep are presented. this paper suggests that engineers should use the initial stress method with degree of creep to estimate the influences of creep on high - rise buildings and large span buildings on the basis of conceptual design
基於現有的試驗資料，高層及大跨度民用建築的徐變分析只能參照橋梁結構中的徐變系數方法或水工結構中的徐變度方法進行.從徐變系數的定義出發，利用積分中值定理和疊加原理，推導並修正了加載齡期與起算齡期不同時徐變收縮應變增量的表達式，對比了應用徐變系數分析徐變的有限元法和應用徐變度分析徐變的初應變法在效率和精度上的差別，並建議應從概念設計的角度出發，採用徐變度的初應變法來估算徐變對高層及大跨度民用建築的影響 -
Abstract : creep analysis methods of high - rise buildings and large span buildings can only refer to creep coefficient method in bridge engineering or the method of degree of creep in hydraulic construction engineering under the present experiment conditions. in this paper, the incremental expressions of concrete creep and shrinkage strain when the initial computational age is not the same as the loading age are derived and corrected from the concept of concrete creep coefficient and the mean value theorem of integral and the principle of superposition. the differences of efficiency and accuracy of creep analysis between the finite element method with creep coefficient and the initial stress method with degree of creep are presented. this paper suggests that engineers should use the initial stress method with degree of creep to estimate the influences of creep on high - rise buildings and large span buildings on the basis of conceptual design
文摘:基於現有的試驗資料，高層及大跨度民用建築的徐變分析只能參照橋梁結構中的徐變系數方法或水工結構中的徐變度方法進行.從徐變系數的定義出發，利用積分中值定理和疊加原理，推導並修正了加載齡期與起算齡期不同時徐變收縮應變增量的表達式，對比了應用徐變系數分析徐變的有限元法和應用徐變度分析徐變的初應變法在效率和精度上的差別，並建議應從概念設計的角度出發，採用徐變度的初應變法來估算徐變對高層及大跨度民用建築的影響 -
In redundancy structure, the structure ' s distortion and strain will change along with time because of creep. according to the characteristic of concrete ' s creep, the creep grows quickly in the concrete " earlier age. for the long of bridge ' s construction period, the concrete ' s age of different part are discrepantly
在超靜定結構中，結構的變形和內力都會因徐變而隨時間不斷變化，對于實際的工程結構，結構的整體總是分階段建造起來的，某些荷載（如自重）也是在結構建造過程中分階段作用在不斷生長的結構上的。 -
Based on the creep experimental curve, the creep deformation law of silty soft clay of the first marine layer and its constitutive relationship among stress - strain - time is studied in this paper
本文在蠕變試驗曲線的基礎上，研究了天津市第一海相層淤泥質粉質粘土的蠕變變形規律，得出應力、應變、時間三者之間的本構關系。 -
Available empirical results indicate that the creep of reinforcement strongly influences the overall behavior of rs structures, which is demonstrated by excessive deformations. different creep tests are discussed and the test methods to obtain the two kinds of creep curves are compared in this thesis. the methods of how to determine the reduction factor according to long - term strength of creep or allowable strain during the services life are presented
文中介紹和研究了不同的蠕變試驗手段，比較了獲得兩種蠕變曲線的試驗方法，並給出了兩種蠕變曲線一定范圍外推的數據處理方法;給出怎樣根據設計使用年限的長期蠕變強度或容許應變來確定蠕變折減系數的方法，並用計算實例來說明。 -
The presence of small amount of liquid at grain boundaries tends to form thin viscous layer which surrounds the finer grains. intergranular fracture may occur at the grain boundaries between two fine grains not covered by viscous phases. the high ductility achieved at low strain rates is generally attributed to dislocation glide - creep accommodation mechanisms
原始晶界上產生少量液相，形成薄的固液共存粘性層並包圍細化的晶粒，沿晶斷裂主要發生在無粘性層的細晶粒間；而在較低應變速率下，三叉晶界位錯攀援?蠕變協調機制鬆弛晶界滑移產生的應力集中，晶界上產生較多液相，有利於晶界滑移進行。 -
Standard test method for elevated temperature tensile creep strain, creep strain rate, and creep time - to - failure for advanced monolithic ceramics
高級單片陶瓷的高溫抗拉蠕變應變，蠕變應變率及蠕變斷裂時間的標準試驗方法 -
3. the two stages of primary creep and steady - state creep of 3d c / sic correspond to the gradual saturation of matrix crack and the opening of these cracks respectively. the transverse crack is the main contributor to the macroscopic creep strain of 3d c / sic, and its opening is controlled by the creep temperature
（ 3 ） 3dc sic復合材料的減速蠕變階段和穩態蠕變階段分別對應著基體裂紋趨于飽和和逐漸張開這兩個過程；橫向基體裂紋是3dc sic復合材料宏觀蠕變應變的主要貢獻者，溫度是影響橫向裂紋張開速度的一個重要因素。 -
Test results show that : ( 1 ) the amount of creep deformation during monotonic primary loading depends on strain rate before creep, creep stress level, and creep time ; ( 2 ) during monotonic primary loading, the stiffness increasing magnificently shortly after creep ; ( 3 ) the direction of creep will change from positive creep ; to neutral creep and negative creep during unloading, while during reloading, it will change from negative, to neutral and positive creep
試驗結果表明： （ 1 ）在初始加載過程中，經過一定時間蠕變后黏土的強度有很大的提高； （ 2 ）在卸載過程中，隨應力值下降黏土的蠕變表現出由正蠕變、中性蠕變到負蠕變的逐漸轉化； （ 3 ）在重復加載過程中，隨應力值增加黏土的蠕變表現出由負蠕變、中性蠕變到正蠕變的逐漸轉化。 -
It ' s the first time clearly and systematically to present the concepts of restraint influence coefficient of steel to strain increment, to curvature increment and to deflection increment due to creep which are different each other. theoretical formulae are established, and approximate formulae are also obtained while considering the characteristics of common - used concrete and ambient condition of real bridges in china. so, an approximate restraint influence coefficient method to analyze the effect due to creep and shrinkage in pc bridges is put forward, and the equations to estimate second - force due to creep considering influence of steel in system - transferred continuous pc bridges is also established
本文首次清晰而系統地提出了鋼筋對徐變的不同效應（徐變應變、徐變曲率、徐變上拱）約束影響系數的概念，建立了相應的計算式；結合我國普遍採用的混凝土的徐變特性和橋梁的構造特點及工作中南大學博士學位論文摘要環境特徵，給出了具有較高計算精度的實用計算式;在此基礎上，建立了橋梁徐變效應近似分析的鋼筋約束影響系數法，並推導出了考慮鋼筋影響的超靜定梁徐變次內力的近似計算式，可方便地應用於橋梁研究和設計中。 -
Using biomechanics methods, through the study of the influence of different injection and maintain period on the expansion efficacy and shrinkage rate of skin, a rapid expansion method with relatively big expansion area is proposed ; biomechanics analysis in vivo is been made on the expanded skin ; comparing the biomechanics property in vitro of the rapid expansion and conventional expansion with different maintaining times, the parameters such as strength, stress - strain relationship, stress relaxation and creep which reflect the characteristic of the expanded skin have been obtained ; making the research of the expanded skin ' s biomechanics changes at different stage after grafting, the long - term and short term diversified regular has been obtained ; making experimental study and discussing the changes in the microcirculation and vessel structure of exceedingly expanded shin, the relationship between survival length of flap and the changes has been gotten
本課題旨在用生物力學的方法通過動物實驗來研究不同注水擴張期和維持擴張期對皮膚擴張量和皮膚回縮的影響，探討有效獲取較大的擴張皮膚面積的快速擴張方法；對擴張皮膚進行在體生物力學特性分析；比較了快速擴張和常規擴張在不同維持期的皮膚離體生物力學特性，得到離體生物力學各參數，如強度、應力?應變、應力鬆弛、蠕變等；為全面了解擴張皮膚在移植后的近期和遠期的變化規律，做了擴張皮膚移植后不同階段的生物力學變化的實驗研究；探討了不同擴張量時皮膚的微循環變化和血管結構變化與皮瓣存活的關系。 -
Considering the characteristics of internal force and structures of simply supported pc bridges, a novel automatically step - up method ( asum ), taking into account the influence of steel arrangement, steel ratio, stress losses of tendons and time - dependent concrete modulus, to analyze creep and shrinkage effects is presented. this method accepts all kinds of expressions of creep and shrinkage, and it is easy to calculate total stress, strain of concrete and steel and deflection of bridge at any time, the expected prediction accuracy will be obtained by further dividing the time - step within duration
首先，針對預應力混凝土簡支梁橋的受力特徵和構造特點，提出了徐變效應分析的全量形式自動遞進法，可考慮截面上鋼筋位置、配筋率、預應力鋼筋鬆弛、混凝土彈性模量隨時間變化等影響，且計算式可適用於任何形式的收縮、徐變特性表達式；建立的公式可方便地求解任意時刻混凝土、鋼筋的應力與應變和跨中梁體的豎向變形，計算精度可方便地通過計算時段的細分來控制，直至給出滿意的結果。 -
From an examination of the tensile behavior of cz ly12 alloys under different temperature and strain rate, two kinds of deformation and intergranular fracture behaviors were observed that were opposite to the characteristic strain rate range in fine - grained superplasticity. the mechanisms are described as follows. the high ductility achieved at high strain rate is generally attributed to the dominant role of gbs accommodating mechanisms, which is considered as dislocation creep within grains controlled by subgrains
研究選用自然時效淬火態的ly12鋁合金，進行了一系列不同溫度和應變速率下的單軸拉伸試驗， 480下，觀察到與傳統細晶超塑性特徵區間相反的行為：較高應變速率下，動態再結晶使晶粒細化，促進了晶界滑移，亞晶界控制的晶內位錯蠕變是晶界滑移的主要協調機制。 -
Nonlinear least square method programs which are used to curve fitting were programmed in matlab language. creep data of 600 < wp = 5 > were curved and analysized based on strain hardness theory and function method
運用matalab語言編制非線性最小二乘法擬合程序，用應變硬化理論和函數法擬合600的蠕變數據，並進行分析。 -
To the problems in long - term monitoring of concrete stress, the numerical simulation for concrete creep effect of the main girder segment of wenhui bridge was made ; accordingly a method that can approximately separate the creep strain was put forward
針對目前混凝土應力長期監測中存在的問題，對文暉大橋主梁節段進行了徐變效應的數值模擬分析，並提出了近似的徐變應變分離方法。 -
After the evaluation of the three parameters in the proposed creep model, which is based on the large numbers of experimental measurements of concrete creep, the influential regularities of concrete filled steel tube columns under long - term loading are investigated. by dispersing time, the method of tangent modulus is adopted to study the relation of creep strain and load time. in the end, this paper took cft specimens with representative geometry and sectional dimensions as examples and adopted the proposed method as an approach to investigate the influencing regularities of many factors, which include the ratio of long - term load to strength, the slenderness ratio, the eccentricity ratio, and the intensity grade of concrete, on cft structures
在對鋼管混凝土構件長期荷載效應的分析中，本文基於三維粘彈性理論，採用三參數粘彈性模型，提出了核心混凝土徐變的三維有限元分析理論，在總結過去大量關于混凝土徐變試驗實測結果的基礎上擬合了模型中的三個參數，並成功將其應用於鋼管混凝土徐變的三維分析計算中，得到徐變與持荷時間的關系，以典型截面形式的圓鋼管混凝土軸壓、偏壓構件為例，對軸壓比、長細比、含鋼率、偏心率以及核心混凝土等級分別進行了大量的參數分析和實驗對比研究，結果表明二者符合較好。 -
4. the recurrence formula of the creep strain is the key of fem calculation of creep stress. in this paper the exponential function is used to figure the creep strain, and the recurrence formula of 3d creep strain at any periond of time is derivated
徐變變形遞推計算公式是溫度徐變應力有限元計算實現的關鍵所在，本文用指數函數式表示徐變度，在此基礎上，對三維空間問題徐變變形進行了研究，推導了任一時段徐變增量的遞推計算公式。 -
The study on high - temperature low - cycle fatigue life and fatigue crack propagation life under multi - axial stress state shows that the fatigue life and fatigue crack propagation life can be characterized by the equivalent plastic strain range p, the equivalent creep strain range c and the equivalent strain range, and do n ' t exit notch dependency, non - notch - dependency equations being given in the paper
） _ c和當量應變范圍（ ? ）進行多維應力狀態高溫低周疲勞總壽命及裂紋擴展壽命評價是可行的，且不存在缺口依存性。並給出無缺口依存性的疲勞總壽命評價方程。
分享友人